Question about 2002 Volvo S60

Open Question

Right turn signal turns on high beams - 2002 Volvo S60

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Pyrhyc
  • 2028 Answers

SOURCE: turn signals and high beams

First check around all the lights (front, rear, headlight, turn signal, parking, fog, etc..) for loose, broken, or bare wires, and/or loose , broken, or bad connectors. Any of these could cause the lighting to short. If everything is in good working order, then the problem will most likely lie with switch inside the column (the lever).

Posted on Jul 15, 2008

Ad
egan890
  • 1 Answer

SOURCE: 91 740 high beam will not stay on

Thanks to all who helped on this issue, the problem was solved after I replace the Orange roung relay. under the ush trey, it controls the light out unit.

Posted on Dec 31, 2008

  • 3 Answers

SOURCE: no high beams, blinkers or information display

you might have a wire disconnected or is loose also check your fuses you might have a blown fuse

Posted on Nov 10, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 chev sub head lights wont turn on


Do you know anything about automotive electronics ? Electronic control modules .
Headlamp ON/OFF control is determined by the body control module (BCM) by a signal on the headlamp switch on input circuit when the headlamp switch is in the HEAD position. When the headlamp switch is in the AUTO position, the BCM determines headlamps ON/OFF by the voltage from the ambient light sensor.
If the headlight switch is left in the ON position, the inadvertent power control feature will turn OFF the headlights approximately 10 minutes after the ignition switch is turned to the OFF position. If the driver places the headlight switch in the ON position after the ignition switch has been turned OFF, or if the ignition switch is in the ACCY position, the headlights will remain ON until turned OFF or the battery runs dead.
The high beam indicator is illuminated when the instrument cluster receives a GMLAN serial data message from the BCM that the high beams are illuminated.
High Beams
The high beam headlamps receive voltage from the headlamp high relay located in the underhood fuse block. The BCM controls the relay on the headlamp high beam relay control circuit. High beam control is determined by a signal on the headlamp dimmer switch signal circuit from the multifunction switch. When the headlamp dimmer switch signal circuit is grounded, the BCM grounds the headlamp high beam relay control circuit, illuminating the high beam headlamps. The right and left high beam circuits are independent and are fused independently in the underhood fuse block.
Low Beams - Standard
The low beam headlamps receive voltage from the headlamp low beam relay located in the underhood fuse block. The BCM controls the relay on the headlamp low beam relay control circuit. Low beam control is determined by a signal on the headlamp dimmer switch signal circuit from the multifunction switch. When the headlamp dimmer switch signal circuit is open, the BCM grounds the headlamp low beam relay control circuit, illuminating the low beam headlamps. The right and left low beam circuits are independent are fused independently in the underhood fuse block.

Hooking up a factory scan tool an checking DTC'S - diagnostic trouble codes would be the very first step in trouble shooting this problem .
DTC B257A 00: Headlamp Switch Input Signal Mismatch
DTC 2575 00: Headlamp Control Circuit

Jun 30, 2017 | Cars & Trucks

1 Answer

Right low beam headlight does not come on but my right turn signal will stay even tho i diddnt turn it on. If I cut on my high beams the rurn signal cuts off. Whats wrong? Helo


It could be the lamp control module !
Headlamps
Battery positive voltage (B+) is applied at all times to the lamp control module (LCM) through the underhood fuse block HDLP fuse.
When you place the headlamp switch in the HEAD position, the headlamps input to the LCM is grounded. The LCM then applies battery positive voltage (B+) through the underhood fuse block HDLOBML fuse and HDLOBMR fuse, which feed the left low beam headlamp and the right low beam headlamp respectively. When you activate the headlamp dimmer switch by pulling on the multifunction lever until the switch clicks, the high beam input circuit to the LCM in grounded . The LCM then removes battery positive voltage (B+) from the low beam headlamps and supplies battery positive voltage (B+) through the underhood fuse block HDHIBML fuse and HDHIBMR fuse, which feed the left high beam headlamp and the right high beam headlamp respectively.
Check this fuse in the left under hood fuse box first. HDLOBMR Fuse 18 10 Amp. RH Low Beam Headlamp . If the fuse is good check for B+ voltage with the low beams on . Use a test light or volt meter . If you look on top of fuse there are two metal tabs ,check there for B+ voltage , If no B+ voltage the LCM - lamp control module isn't supplying any .
Lamp Control Module (LCM)
Under the left side of the IP, to the right of the steering column
Turn Signal Flasher
Under the left side of the IP, to the right of the steering column
Lighting Systems Component Views in Lighting Systems
Lighting Systems Connector End Views in Lighting Systems
Turn Signal/Hazard Switch
In the left front of the passenger compartment, in the steering column

Apr 28, 2016 | 2000 Buick Park Avenue

1 Answer

HIGH BEAMS COMES ON WHEN USING TURN SIGNAL AND LOW BEAMS ARE ON


Hello, is sounds like your issues are coming from within your turn signal/high-low beam switch. Most of the time the wires get worn or break and start rubbing around on each other causing troubles within the electrical circuit. Other times the contact switches inside the turn signal/high beam switch/lever wear and loose contact over time. You may be able to see wires leading from switch into steering colum. Check for bad wires, if none you may have to replace switch which you can get from any junkyard for bout 5 bucks plus learn how to take it apart in a junk car no one is worried about getting destroyed. BE CAREFULL WITH AIRBAGS when you pull your steering wheel to fix switch. It is not a difficult job to do.

Jan 16, 2013 | 2005 Ford Escape

2 Answers

Dodge ram 3500 turn signal - headlight problem


WAY TO GO !!! another "great idea" from vehicle manufactures

Jun 07, 2012 | 2004 Dodge Ram 3500 Truck

1 Answer

When I use my turn signal switch to turn left or right, it makes my high beam lights turn on. However if I hold my switch a certain way and click it to turn left or right the high beams dont come on. Now...


My vote would be for the switch. I'm not sure but I think there are seprate relays for all the diffrent functions on the switch. Look online for a wiring diagram for the switch, I found one for my lincoln. Hope this helps. Peace

Aug 13, 2011 | Saturn L300 Cars & Trucks

1 Answer

2001 buick regal 4 door - headlight flicker on and off. If they go all the way out, you can get them back on by kicking under the dash right above the brake pedal. I removed the cover but cant locate the...


Have you tried wiggling the turn signal lever when the problem occurs? I have seen multiple cases where the wiring inside the headlight high beam/turn signal switch melts and causes the problem you are describing. If you can wiggle the high beam/turn signal switch and CAUSE the problem, you have a defective high beam/turn signal switch.

Aug 05, 2011 | 2001 Buick Regal

1 Answer

My light problem is i have low beam on right side no low on left side i turn highs on and right side goes out and high on left turns on then when back to lows beams and i pull turn signal to flash high...


If you have separate bulbs for the low and high beams(4 light system), if you pull the turn signal and hold it, all 4 lights will stay on until you release the turn signal. You need to replace the bright bulb on the right side and the low bulb on the left side. If your headlights only have one bulb on each side, then you will have to replace both of them to get everything to work.

Jan 04, 2011 | 2000 Ford Mustang

2 Answers

When I turn on my right turn signal, my high beams come on. Will replacing the switch fix this?


If you have a multi-function dimmer/turn signal switch: YES it will correct the problem.

Mar 07, 2010 | 2001 Pontiac Aztek

2 Answers

High beams come on when turn signal used.


it is the multi switch. I am replacing mine right now. i had to take the high beam bulbs out..

Oct 08, 2009 | 2002 Saturn L-Series

1 Answer

Turn Signal Lever 2004 Ford Focus LX


$35 sounds right for the lever. It definitely sounds like it's your lever acting up as the contact seems to be stuck

Oct 02, 2009 | 2004 Ford Focus

Not finding what you are looking for?
2002 Volvo S60 Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...