Question about 1994 Chevrolet Corsica

1 Answer

Putting windshield in 94 corsica

I am installing a windshield in my corsica and I want to know if I put caulk on the frame or the glass? How thick of a line of caulk do I use?

Posted by on

  • Wendy Campos
    Wendy Campos May 17, 2009

    I have a drivers side air bag but no passenger. We took cracked window out and are ready to install the new one. We need to know where to put the caulk, window or frame and how much to use. Why does it matter about the airbags?

  • David Neuberger May 11, 2010

    Does this car have air bags?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 232 Answers

No caulk,you need to get a new windsheild seal,unless you already have ,it has all the adhesive needed.

Posted on May 17, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Install new glass in rear passenger doors


I'm not familiar with that particular car but I'll tell you what I know about rear door glass. On most cars you have to remove the door trim and handles, then strip the window rubbers / flock trim from the door/window frame. There will be various screws hold the guides and winder or motor in place. Remove the quarter light frame if it has one. The door glass guide rails and then enter the glass through the top of the door, tilting it accordingly. When you have the glass inside the door assy, get an assistant to take the weight of the glass while you reassemble the glass guides etc in the reverse order. Be patient because its a fiddly job rather than difficult.

Jul 03, 2015 | 2005 Dodge Stratus Sedan

1 Answer

How do i remove a rear window


hard top or convertible.?
I guess at hard.
Not side rear. or doors., but rear rear. as in rear view.

rear window. glass out? why not say why so can see JOB ? at hand.
eg: my rear view glass is broken.?

is covered in the FSM, (like all cars made)
the factory service manual. or alldata.com (clone) log in read.

ok ill past the FSM words here.
Stationary Windows Stationary glass is removed and installed using the same procedure as the windshield. Refer to Windshield Glass Removal and Installation. (first hit ,btw)
https://www.youtube.com/watch?v=5dp2VVvPlXc
ever seen a front windshield changed out, sure.
same
best solution is......
Call the same company to come out and point to rear .?

they sell a special tool to get out a window.
it has 2 , "T" handles and rod saw. to cut out the glue/caulk.
the glue comes out more easy on a hot day.
its not really glass, it's an occupant containing device, today.
the best caulk is.
3M 08693 Auto Glass Urethane Windshield Adhesive Cartridge
how is my guess.... on car, and glass and reasons.

Dec 04, 2014 | 1992 Suzuki Swift

1 Answer

To buy auto glass rubber sealant


where?
the front windshield? uses special caulk that is rated for
occupant containment strength. (laws regulate it type)
rubber what rubber?
the sealant is surely not rubber.
if you Google using plain text. you get .200,000 hits.
1st one below.... ask any glass shop (auto) for they favorite.
(easy to use)

http://www.amazon.com/3M-08693-Urethane-Windshield-Cartridge/dp/B000RW1XCK

that was my useless guess.... not knowing WHAT glass....

Jul 28, 2013 | 2001 Jeep Wrangler

2 Answers

The rear window to my van came off and shattered during a windstorm... i bought a window off of craigslist.. and can't install it. I dont need it to work,i just need it to go back on.. my bf is taking...


is it a fixed glass or a moveable glass.

Fixed glass is placed against a bead of urethane sealer, like caulking.

Window, Liftgate, Stationary Removal
ssw~us~en~file=ani_caut.gif~gen~ref.gif WARNING: SAFETY GLASSES AND GLOVES MUST BE WORN.
ssw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use only urethane for after-seal to service air and water leaks in urethane seal. Failure to do this may result in additional leaks.
ssw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Allow all glass parts installed with urethane ample time to cure. If ample time is not allowed, glass may come loose and/or leak.
  1. Remove window wiper pivot arm (17526) .
  1. Remove all window glass stops.
  1. Using Rotunda Glass Adhesive Cutter 118-00050 or Rotunda Deluxe Glass Adhesive Cutter 163-00001 or equivalent, follow manufacturer's instructions and cut seal and dam around entire outer edge of windshield glass (03100) .
  1. Remove glass from vehicle.
  1. Trim urethane left on flange with a utility knife or razor blade until surface is smooth and free of cuts. It is not necessary to remove all urethane from the flange if it is cured. However, at no point should existing urethane material exceed 2.54mm (0.10 inch). NOTE: If urethane has not cured completely, remove all uncured urethane using care not to smear urethane on component parts.
    Check flange sealing area for damaged sheet metal or foreign objects which may have caused, or may cause, glass breakage. Service sheet metal if necessary.
Installation
  1. If existing urethane on metal flange has become contaminated, cut away contaminated urethane with a utility knife or razor blade.
  1. If painted sheet metal has been exposed anywhere along the flange, apply Urethane Metal Primer WSB-M2G234-C or equivalent over the painted surface using a clean brush. NOTE: A minimum of 30 minutes is required for primer surface to dry.
  1. Place the windshield glass on a low, stable work surface, inside up. NOTE: Wipe off immediately after application because it flash-dries.
  1. Using a lint-free cloth, wipe outer 25mm (1 inch) of inside glass periphery with Urethane Glass Wipe WSB-M5B280-C2 or equivalent.
  1. Position mouldings on glass. ssw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Allow all glass parts installed with urethane ample time to cure. If ample time is not allowed, glass may come loose and/or leak.
  1. Thoroughly shake and stir Urethane Glass Primer WSB-M2G314-B or equivalent to ensure uniform pigment mixing.
  1. Using a clean brush, apply primer around entire periphery of glass on inside surface as shown. (Allow at least five minutes drying time.)
  1. Properly align glass to body.
    1. Make sure lower windshield glass stops are in place at bottom of windshield glass opening.
    1. Place windshield glass into opening. Center it top and bottom, side to side, with about equal clearance around opening.
    1. Using masking tape or crayon, make alignment marks at points on both the windshield glass and the window opening.
  1. Remove windshield glass from vehicle and place back on work table.
  1. Apply an even bead of Urethane Adhesive WSB-M2G316-B on top of existing urethane around entire window opening using an air pressure cartridge gun. Air line pressure should be around 276 kPa (40 psi). The bead should be large enough to seal the windshield glass but not cause expulsion into vehicle.
  1. Install windshield glass onto vehicle, taking care to align marks on glass to those on body. This must be done within 10 minutes of applying urethane.


Dec 20, 2010 | 1995 Ford Windstar

1 Answer

Replacing a windshield


Using a wood chisel or screwdriver, remove the rubber molding around the windshield. Then, from inside the car, put a firm/steady pressure on the glass. It should lift out. clean ALL of the black adhesive caulk from the metal frame and install new black caulk. Press in the new windshield - and reinstall the rubber molding.

Mar 11, 2010 | 2003 Ford Focus

2 Answers

Well a 99 lexus gs 400. car got broken into. they cut the little glass out in the back passenger side. how can i fix or wherer to get fixed


bro check with dealer or wreckers for the parts and most properly you have to go to windscreen man o some wreckers do fix it with some extra laborer cost

Aug 26, 2009 | 1992 Lexus Ls 400

1 Answer

Install rear window 2001 cabriolet convertible


Yes the glass does have a runner or rubber seal on it. If you have removed it from the frame and the frame is still strong enough to hold up for a while, then here is how you do it: place the rubber seal on the winow glass, have a piece of strong string (about 24 inches long), place the window on the frame for now (don't push it in yet, just park it on top of the frame, get in the trunk, get the string to pass between the frame and the rubber window seal, use the string to position the rubber seal while someone outside the car pushes firmly on the window (helping you pop it in, inch by inch). You have to work from one corner all the way around the frame until you get back to where you started from.It takes a while, it's frustrating and remember not to remove the string before you are completely done because you'll have to start over from scratch. Also, once done, for good measure, tape some painter's tape (low-level of stickiness) about a 1/4inch from the outside rubber window seal (all the way around) and fill the inside of the rubber seal with a thin layer of clear caulking (bathroom or exterior grade). then just smooth out the rubber seal while the caulking is still wet so as to remove any bumps or uneveness. Repeat once a year and you'll be sure that your Cabby won't leak water from the back window, and won't have a rusty back window frame that rots out eventually.
Hope that helps, Cheers!

Aug 05, 2009 | 1993 Volkswagen Cabriolet

1 Answer

Trying to install window tint on the upper portion of the front windshield, but am not able to tell how the rear view mirror comes off. Tried to find a set screw, but could not locate one.


You'll find it's bonded "glued" to the glass, if you try to pull it off it will probably crack the screen as it is laminated and each layer is only 2mm thick or so.
Your best solution would be cutting the tint to size and cutting around the mount putting the split above the mirror mount. As you would cut wall paper around a light switch in a cross then trim to size with a sharp blade.

Jun 03, 2009 | 2008 Mazda Mx 5 Miata

1 Answer

Replace driver side mirror


Go to local auto glass shop or auto supply store. Order a new mirror (not expensive). Ask also for the proper adhesive.

Put on some thick gloves (use pliers if needed) and remove the old glass.
Remove old adhesive from the mirror frame.
Apply adhesive to frame
Put new part in place and hold for a few seconds (read adhesive instructions).

That is it.

Please rate if this helps give your direction.

Jun 02, 2009 | 2002 Chrysler Town & Country

1 Answer

Cooling fan 94 corsica


Replacing the fan is a straight nut and bolt job.
The fan is going to be the expensive part.
I would suggest a local wrecking yard for the part.

Oct 18, 2008 | 1994 Chevrolet Corsica

Not finding what you are looking for?
1994 Chevrolet Corsica Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...