2007 Honda Pilot Logo

Related Topics:

A
Anonymous Posted on Dec 24, 2013

2007 honda pilot check engine light on

Oxygen sensor

5 Related Answers

David Catrett

  • 12 Answers
  • Posted on Dec 03, 2008

SOURCE: check engine light for 1995 honda accord lx wont turn off

First off, Hondas do not run MAF. If the car seems like it is driving better than before the light came on, it could be that the code just hasnt cleared yet. My 95 accord did the same after a fix, I just had to drive it to run the drive cycles.

Ad

Anonymous

  • 141 Answers
  • Posted on Jan 15, 2009

SOURCE: changing oxygen sensor for a 2000 honda civic lx

both are located in the exhaust system. You have to get the car off the ground and follw pipes. You cant miss the O2 sensors.

sheiden9

sheiden9

  • 87 Answers
  • Posted on Apr 05, 2009

SOURCE: 1998 honda accord obd code P0171 and P0170.

Hi,welcome to fix ya.
p0171 is for a lean fuel condition .A variety of things can cause this code the most common one is a bad o2 sensor but a plugged injector,fuel filter or dirty egr system can cause this as well.

Anonymous

  • 1 Answer
  • Posted on Apr 23, 2009

SOURCE: steps to reset 2007 honda pilot oil gauge

From page 232 in the 2007 Honda Pilot Owners Manual.

1. Turn the ignition ON.
2. Press the Select/Reset knob until the engine oil life indicator is displayed.
3. Press the Select/Reset knob for more than 10 seconds. The engine oil life and maintenance item code(s) will blink.
4. Press the Select/Reset knob for another 5 seconds. The maintenance item code(s) will disappear, and the engine oil life will reset to "100".

Anonymous

  • 3600 Answers
  • Posted on Aug 14, 2009

SOURCE: oxygen sensor replacement

you need to rent an 02 sensor socket and use a ratchet and the socket to remove it, there are two on the exhaust pipe one before the cat, you can see it on the exhaust pipe and one after. normally the 1at one goes out. cost $75.00 please rate if helpful.

Testimonial: "it was very helpful! thanks"

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

2013 honda pilot fwd check engine vtm light

wow no engine told at all.nor VIN, double wow
cylinder bank shut downs are a feature to save fuel and is complex
read why here/.
part of VVT and guess what bingo that, may be failing.

https://www.obd-codes.com/p3400
0helpful
2answers

How do i reset my manint req's light after an oil change on a 2003 Honda pilot

Reset oil service light Honda Pilot. From years: 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012.
How do you reset oil service light Honda Pilot. From years: 2003, 2004, 2005.
  1. Turn off the engine. Press and hold the SELECT/RESET button in the instrument panel and turn the ignition switch to run (one position before starting).
  2. Hold the button for at least 10 seconds, until the indicator resets.
  3. Turn the ignition off and then start the engine to verify the indicator has been reset.
How to reset oil service light Honda Pilot. From years: 2006, 2007, 2008, 2009, 2010, 2011, 2012.
Resetting the Engine Oil Life Display if maintenance service is done by someone other than your dealer, reset the maintenance minder as
follows:
  1. Turn the ignition switch to the ON (II) position.
  2. Press the select/reset knob repeatedly until the engine oil life is displayed.
  3. Press the select/reset knob for about 10 seconds. The engine oil life and the maintenance item code(s) will blink.
  4. Press the select/reset knob for another 5 seconds. The maintenance item code(s) will disappear, and the engine oil life will reset to 100.
All information is taken from the Honda Pilot owners manual.
0helpful
1answer

2007 Honda Pilot VSA Stays on with the Triangle

A hazard warning could just mean an oxy sensor...I would inspect the vehicle ft. to back ...check brakes and all ...make sure all vacumn hoses and plugs /wires /and brakes are good.Then disconnect the negative battery cable to reset the system....If it comes back on it is probably just an O2 sensor going bad....meaning oxygen sensor...this is an air fuel mixture sensor which is common to go bad on all cars and trucks......No big deal....Hope this helps ....Metalpoet
2helpful
1answer

My 2007 honda pilot while running the vsa light come on and then the engine light come on and the lose power

My 2007 Honda pilot did the same thing. I took the above advice regarding the oil condition (mine was obviously poor, although I change it every 3 mos) and had it changed immediately. The engine light, VSA light, and the triangle with ! all cleared and the vehicle began to run properly again. No problems since. Thank you to Shawn Bruns!!
1helpful
4answers

PO172 system too rich bank 1 for my Honda pilot 2007 comes up how do i rectify this fault?

Hi,
You need to have the fuel pressure checked, if this is ok you then need to check the valve clearances and once this is done then have the DTC rechecked.
If the P0172 code comes back then you need to check injector pulse timing and then replace the faulty injector.
Let me know if you need more information.
Thanks
0helpful
1answer

My 2003 pilot the emision light keeps coming on.

first and formost you absolutely must have a Honda o.e.m gas cap installed!!!!! second when installing cap make sure you tighten three full turns past snug(3 ratchet sounds)third depending on milage this car should still be under 8yr80kmile emmisions warranty so double check,repairs will be under hondas wing if it is.
0helpful
1answer

2007 Honda Pilot engine light on and starting a problem at times.

You must make a diagnostic through out the ecu,it can be probably the crankshaft sensor.
1helpful
1answer

Check engine light

P0041 Downstream Oxygen Sensors Swapped From Bank To Bank
How does a P0041 code trigger the check engine light? This code will trigger the light to come on under the following condition:

The Heated Oxygen Sensor Monitor, a strategy built into the computer, determines if the Heated Oxygen Sensor (HO2S) signal response for a change in fuel trim corresponds to the correct engine bank. If a response from the Oxygen Sensor being tested is not indicated, a trouble code will be set and the MIL (Malfunction Indicator Lamp) will illuminate.
Possible Causes:
Crossed Heated Oxygen Sensor harness connectors
Wiring swapped from one Oxygen Sensor connector to the other
Wiring changed at the computer connection or in the related harness
Not finding what you are looking for?

396 views

Ask a Question

Usually answered in minutes!

Top Honda Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

john h

Level 3 Expert

29494 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...