Question about 2004 Dodge Neon

Open Question

'04 Dodge Neon HVAC system

How do I remove the HVAC system from my neon? I have removed the dash and all bolts I can see. Are there any bolts that i couldn't have seen?

Posted by on

  • 1 more comment 
  • kwal_91 May 17, 2009

    i disconnected everything but when i try pull it out it feels like theres something holding it in the middle of it

  • jg1523 May 11, 2010

    Is it at all loose? Did you get the drain tube off?

  • jg1523 May 11, 2010

    Did you remove the bolts that hold it in from the engine compartment? Did you disconnect the heater hoses and the a/c hoses ? Did you disconnect the drain tube?

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

farroutideas
  • 78 Answers

SOURCE: Water leaking from the Overflow tube out of the HVAC

Hi there;

Did you say coolant is coming from the HVAC? as in the heater box?
If so does it smell sweet in the cab & do the windows fog up when you turn on the defrost with it set on hot?
If you answered yes to these three questions, chances are very good you need to replace you heater core.
If the coolant is coming out of the overflow tank as soon as the engine is running & you find one or more of your spark plugs are white or very much diferent than the others you most likely have a head gasket leak.
With the info you have included I would have to point my finger at the heater core though.

Good luck, hope this helps, Let me kn ow if you need more input.
Farrout!

Posted on Mar 23, 2009

  • 50 Answers

SOURCE: 2000 Dodge/Chrysler neon Removing rear speakers

I don't know of any websites with pics or vids, but i can walk you through it. First, remove the trim panels between the rear door glass and rear windshield. They're just held in by little clips and should pull right off. Then grab the rear seat cushion at the front about midway to the middle on each side and yank it up sharply. Take the bolts out that hold the rear seat back in place, I think you have to lift it from the bottom to disengage clips at the top. Remove the rear seatbelt trim bezels. Slide the seatbelts through the slots and pull the shelf trim forward to remove it. The speakers are held in by 4 phillips head scews.

Posted on Apr 12, 2009

  • 412 Answers

SOURCE: removal of tensioner pulley in a 2003 Dodge Neon

the tensioner is part of the engine mount bracket..not serviced seperately as far as i know

Posted on May 23, 2009

pippall
  • 1486 Answers

SOURCE: 2001 dodge neon rear drum removal wheel cylinder

You need a pullers to get it off.But if your lucky putting a screwdriver between the drum and back-plate and pize it when your hitting with a hammer it may come off.good luck.

Posted on Jun 03, 2009

taran_2005
  • 10515 Answers

SOURCE: for what sensor is the code po340 on a dodge neon

Hi,
This indicates that a problem was detected in the camshaft position sensor circuit. Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM. Don't just replace the CPS (camshaft position sensor) and think that will definitely fix it.

With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:

  • Visually inspect all the wiring and connectors in the circuit
  • Check for continuity in the circuit wiring
  • Check the operation (voltage) of the camshaft position sensor
  • Replace the camshaft position sensor as required
  • Check the crankshaft position circuit as well
  • Replace circuit wiring and/or connectors as required
  • Diagnose/replace the PCM as required
Thanks.

Posted on Jun 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wont shift gears


Dodge Neon Questions - 04 neon will not go into high gear ...

www.cargurus.com > Questions > Dodge > Neon

CarGurusNov 3, 2012 - 04 neon will not go into high gear - 04 neon won't go into high gear. changed transmission fluid. (it tried to change after fluid was changed) gas cap ... ... Car: 2003 Dodge Neon SXT, automatic transmission. As of today, I have ...

Dodge Neon Questions - 2005 Dodge neon does not shift ...

www.cargurus.com > Questions > Dodge > Neon

CarGurusApr 6, 2014 - Your cars computer gathers info on speed in order to shift gears properly.... then you won't have a speedo and the ECM will not tell the TCM to shift gears in the trans. .... Car: 2003 Dodge Neon SXT, automatic transmission.

Neon wont shift out of first gear auto. - DodgeTalk : Dodge Car ...

www.dodgetalk.com > ... > Dodge Neon - General Talk
Jul 30, 2011 - I have a 2003 dodge neon se and it will run and drive. The transmissonwill not shift out of first gear. Where do I start? Compare to Toyota Tundra. Get Tundra on ... 2000 Stratus won't shift out of First Gear
Mar 14, 2007
Not shifting out of Second Gear???
Jan 15, 2007
46RE wont shift out of first at full throttle.
Nov 17, 2006
Transmission wont shift
Nov 3, 2005
More results from www.dodgetalk.com

Jan 06, 2016 | 2003 Dodge Neon

1 Answer

How to remove brake line from front caliper of 95 dodge neon


The brake hose is attached to the caliper with a banjo bolt. Use a socket/ratchet or wrench to loosen the bolt. Once the bolt is removed the hose can be removed fro the caliper.

Apr 02, 2013 | 1998 Dodge Neon

1 Answer

How do I install a headlight assembly for a 2005 dodge neon


HEADLAMP MODULE REMOVAL
  1. Release hood latch and open hood.
  2. From behind bumper fascia, remove bolt holding outboard end of module to fender.
  3. Loosen bolts holding inboard end of module to radiator closure panel.
  4. Remove bolt holding grille to headlamp module.
  5. Remove bolts holding top of module to upper crossmember Headlamp Module
  6. Disengage wire connector from headlamp and parking lamp sockets.
  7. Separate headlamp module from vehicle.
INSTALLATION Reverse the preceding operation.

Feb 18, 2011 | 2005 Dodge Neon

1 Answer

What has to be removed to take out and replace a starter on an 04 dodge neon?


Remove the intake manifold, the air intake duct, air filter housing, MAP sensor and 2 hoses.

Sep 06, 2010 | 2004 Dodge Neon

2 Answers

Where is the frost plug installed on a 2000 plymouth neon?


there are several.4-6 or more?? if the coolant is rusty, plan on doing all of them or sell the car. BIG $$$$...If you have not kept up with the coolant service,you will have much bigger problems later on. how many miles? at 90k miles replace the timing belt, tensioner and water pump, use factory chrysler parts only. if you dont and the belt breaks, or water pump siezes, the engine will be trashed.

Oct 02, 2009 | 2000 Dodge Neon

1 Answer

I am changing the alternator in a 1998 dodge neon, need diagram


No diagram...
The pivot bolt is the long bolt that holds the alternator to the frame.
If you loosen it, the alternator can "swing" with the pivot bolt as its .... well, pivot, or swing center.

The long bolt must be removed completely in order to remove the alternator.

Be sure to doisconnect the negative cable from your battery.

Hope this hleps w/o a diagram.

Sep 14, 2009 | 1998 Dodge Neon

1 Answer

Cam shaft sensor


it should be on the back of the head opposite the drive pulleys and belts. it should have four bolts holding it on. It looks square in shape.

Feb 10, 2009 | 2004 Dodge Neon

2 Answers

OIl drain plug removal 99 dodge neon DOHC


It appears that the threads are stripped on the bolt or pan. To remove the bolt, try having a helper put a couple of screwdrivers (flat) between the bolt and pan, and while you turn the drain bolt to loosen, have them apply pressure downward on the bolt. If you have a carpenters flat pry bar, that would probably work even better to apply downward pressure to help remove the bolt. Next, you'll have to go to a parts store to get a drain plug that is made to replace one w/ bad threads. Let me know how you do. countrcurt0

Sep 18, 2008 | 2006 Dodge Neon

1 Answer

1995 Dodge Neon


the daytime runnling light module is in the dash under cigarette lighter i got my module for 10 bucks at a junk yard

Aug 15, 2008 | 1998 Dodge Neon

1 Answer

Removing a starter


Yes, you'll have to remove the bracket.

Jun 29, 2008 | 2001 Dodge Neon

Not finding what you are looking for?
2004 Dodge Neon Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...