Question about 1990 Chevrolet C1500

1 Answer

My break lights and turn signals on the rear end dont work. but the the lights on the rear do come on. just no rear brake lights or blinkers

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 59 Answers

You should replace your break light swtich and it is located behind the brake.

Posted on May 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

97 jeep wrangler 2.5


dont break the brakes..... TURNS & HAZ
many blinker, modules , internally flash with any load.
1: check all fuses first... (SOP)
2: then remove the blinker loads from the timer.

see it here
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

see WIRING, (end)
8w-51/52
chapter 8w, page 51-4 shows the switch. (complex it is)
note how brake and turns are shared, resources. (blub elements)
now 8w-52-6
see the flasher module.
see C305 pin 2, any load on that pin will cause it to flash.(inside)
that would be any switch in the combo switch stuck on.

Apr 07, 2014 | 1997 Jeep Tj

1 Answer

Blinkers dont work


Did you replace the flasher?

Jul 31, 2017 | 1994 Chevrolet Cavalier

1 Answer

1994 S10 rear break lights and blinkers do not work.


The headlight switch would have nothing to do with brake lights and turn signals. The turn signal switch would.

Sep 28, 2012 | 1994 Chevrolet S-10

1 Answer

Brakes Lights dont work on a 2006 Chevy Silverado


I've worked on these the first drove me crazy. its the turn signal switch every thing runs thru these. head lights, turn signal, brakes. except the third brake light. it runs directly from the brake switch. go figuare

Jun 22, 2010 | 2003 Chevrolet Tahoe

2 Answers

1998 S10 rear break lights and blinkers do not work.


If the fuses or brake light switch were bad your third brake light would not work same with the multi purpose switch. you either have a wiring problem like some broken wires or the actual light sockets are bad. it is common with gm trucks that the circuit board for the tail lights melts and does not make contact.

Nov 02, 2009 | 1998 Chevrolet S-10 Pickup

2 Answers

Signal lights dont work when breaking


No,this is not normal,this normal when the emergency flashers are on,but not the turn signals.Check the bulbs(all of them)in the rear tail light assembleys.If you can not tell which bulbs are bad,replace them all.Does this vehicle have a trailer light plug?If it does,it could be in it.After the bulb replacement(look at bulbs in your hand to see if filiments are burned)replace the turn signal flasher.To find it turn key on,and left or right turn signal on,and listen,and feel for it under dash around the steering column.

Aug 23, 2009 | 1988 Jeep Comanche

1 Answer

TURN SIGNAL, BRAKE & HAZARD LIGHTS


No Turn Signal Operation (blinker)The turn signal lights in your car are a basic electrical system that controls the front and rear blinker lights to alert the intended direction of the vehicle. We have listed some of the most common problems and repair troubleshooting tips below:
Troubleshooting Procedure
To start troubleshooting this problem:
  • Turn the key to the on position (do not start engine)
  • Inspect the system fuse located in the fuse panel and replace if needed. If you cannot find the location of the blinker fuse consult your owner's manual or an online repair manual
  • When a blinker flasher fails it can cause blinker lights to say on, not blink, or not go on at all. To test the blinker system flasher, remove the flasher unit and insert a jumper wire between the two terminals. If blinker stays on in both directions without blinking, replace the flasher. If you cannot find the location of the blinker flasher consult your owners manual or an online repair manual.
  • 1b7f814.jpg

Jul 09, 2009 | 1999 GMC Denali

2 Answers

Right rear brake light and blinker dont work


when you use the right turn signal, does it blink faster?. Could it be the bulb holder is damaged or rusty?

May 16, 2009 | 2001 Plymouth Neon

1 Answer

Right read blinker/break light dont work, turn signal blinks rapidly


It's the bulb. There are two filliments in the bulb. One is for when you turn your lights on and the other is for breaking and blinker flashing. When the break filliment goes bad it causes the blinker to flash very rapidly. 100% the bulb. Change it and all will be good again. P.S. if it were a fuse none of the break lights or blinkers would work.

Apr 20, 2009 | 2005 Ford Explorer

1 Answer

99 Rodeo Right turn signal makes brake lights blink


TURN SIGNALS WILL FEED BACK THROUGH THE TURN SIGNAL SWITCH.THEY ARE INDEPENDENT OUT SIDE ON THE CAR BUT NOT IN THE SIGNAL SWITCH.REPLACE THE SIGNAL SWITCH

Jan 02, 2009 | 1999 Isuzu Rodeo

Not finding what you are looking for?
1990 Chevrolet C1500 Logo

Related Topics:

179 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...