Question about 1999 Chevrolet Malibu

1 Answer

How do u bleed the brakes or better yet where is the bleeder valve on 99 malibu

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Chevrolet Master
  • 2,007 Answers

On the back of your caliper. Loosen it, stick a hose on it, have the other end of the hose submerged in a pop bottle half full of brake fluid. Pump the brake until there are no more bubbles. Hold the brake down, remove the hose, tighten the bleeder screw before you take your foot off the brake. (or your buddy's foot)

Posted on May 16, 2009

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
ourhowse
  • 2007 Answers

SOURCE: changing brakes

You use a c-clamp to compress the piston. Don't remove the hose or you'll let air in.

Posted on May 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My bleeding screw for the front brakes are both broke Wat should I do I have drums in the back on a 03 Malibu how can I bleed them


You use the bleeder on the rear drums to bleed those lines but you cannot do it to front brakes until you replace the bleeders up there.

Jun 15, 2017 | Cars & Trucks

1 Answer

How to bleed clutch 2007 compass


GRAVITY BLEEDING CLUTCH HYDRAULIC CIRCUIT

1. Verify fluid level in brake master cylinder. Top off with DOT 3 brake fluid as necessary. Leave cap off.

2. Raise vehicle on hoist.

3. Remove bleed port protective cap and install suitable size and length of clear hose (4) to monitor and divert fluid into suitable container.

4. Open up the bleed circuit by turning the thumb screw (3) counter clockwise this will start the air purge and fluid fill process.

5. Lower vehicle, but only enough to gain access to and fill the brake master cylinder. NOTE: Do not allow clutch master cylinder to run dry while fluid exits bleed port.

6. Top off brake master cylinder fluid level while air is purged and fluid drains from bleed port. Continue this until no air bubbles are seen and a solid column of fluid exists.

7. Close hydraulic bleed circuit, remove drain hose and replace dust cap on bleed port.

8. From driver's seat, actuate clutch pedal 60-100 times.

9. Apply parking brake. Start engine and verify clutch operation and pedal feel. If pedal feels fine and clutch operates as designed, stop here. If pedal still feels spongy or clutch does not fully disengage, excessive air is still trapped within the system, most likely at the master cylinder.

10. Top off brake master cylinder fluid level with DOT 3 brake fluid as necessary.

POWER BLEEDING CLUTCH HYDRAULIC CIRCUIT

1. Remove reservoir cap and connect bleeder cap to reservoir. NOTE: Use Bleeder Cap/Modified reservoir cap adapter Snap-on #901-059 or equivalent.

2. Connect service filling machine to bleeder cap. NOTE: Use Service Filling Machine/Brake power bleeder Brake power bleeder or equivalent.

3. Service filling machine should be pressurized to at least 2.5 bar (36 PSI).

4. Remove dust cap from bleeder valve and connect the transparent bleeder hose to bleeder valve.

5. Place the other end of hose in the bleeder container to capture the used fluid. The end of the hose MUST be submerged in the DOT 3 brake fluid.

NOTE: Use Bleeder Container To capture hydraulic fluid and Transparent Bleeder Hose To route fluid to container.

6. Turn on the service filling machine.

7. Crack open the bleeder valve (3).

8. Allow fluid to flow out of bleed port until no more air bubbles can be seen in the transparent bleeder hose.

9. Once fluid is free of air bubbles; make 15 quick actuations between clutch pedal stop positions.

10. Close the bleeder valve and disconnect the service filling machine.

11. To remove remaining air, actuate pedal 10 times slowly between pedal stop positions.

12. Check clutch pedal to see if vehicle is properly bled.

13. If vehicle is not properly bled, repeat procedure.

14. Remove bleeder cap from reservoir and replace reservoir cap.

15. Disconnect transparent bleeder hose from bleeder valve and replace dust cap.

Oct 15, 2013 | 2007 Jeep Compass Limited

1 Answer

How do you bleed the brake system on 2003 suzki grand yitara 4x4 with abs brakes


The hydraulic brake system must be bled any time one of the brake lines is disconnected or air enters the system. There are two ways to bleed the system; pressure bleeding or manual bleeding. Both procedures will be given here, although pressure bleeding requires the use of some fairly expensive equipment (a pressure tank) and is seldom used. Both methods are equally effective.The correct bleeding sequence is: left front, right front, left rear, and right rear. On master cylinders equipped with a bleeder valve, bleed the master cylinder last.
PRESSURE BLEEDING
  1. Clean the top of the master cylinder, remove the cover, and attach the pressure bleeding adapter.
  2. The spring-loaded plunger on the front of the proportioning valve must be depressed while bleeding. Wire or tape can be wrapped around the valve to hold the plunger in.
  3. Check the pressure bleeder reservoir for correct pressure 20-29 psi (137-206 kPa) and fluid level, then open the release valve.
  4. Fasten a bleeder hose to the wheel cylinder or caliper bleeder nipple and submerge the free end of the hose in a transparent receptacle. The receptacle should contain enough brake fluid to cover the open end of the hose.
  5. Open the wheel cylinder or caliper bleeder nipple and allow the fluid to flow until all bubbles disappear and an uncontaminated flow exists.
  6. Close the nipple, remove the bleeder hose and repeat the procedure on the other wheel cylinders according to the sequence.


MANUAL BLEEDING(see Figures 1, 2 and 3)An alternative to the pressure method of bleeding requires two people to perform; one to depress the brake pedal and the other to open the bleeder nipples.
  1. Clean the top of the master cylinder, and then remove the cover and fill the reservoir with clean brake fluid.
  2. To prevent squirting fluid replace the cover.
  3. The spring-loaded plunger on the front of the proportioning valve must be depressed while bleeding. Wire or tape can be wrapped around the valve to hold the plunger in.
  4. Install a box end wrench on the left front bleeder screw.
  5. Attach a length of small diameter, clear vinyl tubing to the bleeder screw. Submerge the other end of the rubber tubing in a glass jar partially filled with clean brake fluid. Make sure the rubber tube fits on the bleeder screw snugly or you may be squirted with brake fluid when the bleeder screw is opened.
  6. Have your friend slowly depress the brake pedal. As this is done, open the bleeder screw half a turn and allow the fluid to run through the tube. Close the bleeder screw, then return the brake pedal to its fully released position.
  7. Repeat this procedure until no bubbles appear in the jar. Refill the master cylinder.
  8. Frequently check the master cylinder level during this procedure. If the reservoir runs dry, air will enter the system and the bleeding will have to be repeated.

Hope helps.

Sep 29, 2011 | 2000 Suzuki Grand Vitara

1 Answer

I just did a complete brake pad replacement on my 99 silverado and I cant get my brakes to bleed. I am using a vacuum bleeder, but cant draw any fluid from the right rear. Am I using the wrong sequence to...


What kind of vacuum bleeder? Is it an air powered type? I have found that with too much vacuum the brakes would not bleed properly. The air powered type had a valve where I could use a small amount of vacuum to work better. I preffer reverse pressure. It naturally pushes the air bubble up through the system and out the master (air rises to the highest point out which would be the master).

Try just opening the bleeder and letting it gravity bleed. One you get a good amount of fluid you can finish off with a vacuum bleed.

Sep 16, 2011 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

Driver side brake not bleeding properly after bleeding left side and changing rotors, calipers, and pads?


first of all make sure master cylinder is full of brake fluid.then you crank car leave foot off brake pedal. watch abs light on dash it should turn off in 10 seconds if not have car towed to garage or dealer. they have to use a scanner to scan the abs brakes if abs light turn off in 3 seconds. then starting bleeding from master bleed the lower brake line fitting at the proportional valve followed by the upper brake line fitting. keep eye on brake fluid in mastercylinder dont let run dry.next prime the abs hydralic modulator.connect the bleeder hose to the rear bleeder valve on the modulator.place the other end into a container partially filled with cleab brake fluid.make sure the end of the hose is submerged.open the bleeder valve slowly about 1/2 to 3/4 turn have an assistant depress the brake pedal and hold it in the depressed position. when the flow of fluid ceases close the bleeder valve.repeat process until no air bubbles are present in the fluid.then tighten the bleed valve securely. start bleeding brakes. your bleeding sequence is right rear - left front - left rear - right front.WARNING IF ALL FAILS YOUR BRAKES DONT FEEL SOLID AND FEEL VERY SPONGY.DONT DRIVE CAR. HAVE IT TOWED TO DEALERSHIP.THEY WILL HAVE TO PRESSURE BLEED YOUR BRAKE SYSTEM.

Nov 17, 2009 | 1999 Oldsmobile Alero

3 Answers

05 chevy classic malibu do brakes need to be bled completely to change pads or just enough to compress piston and where is location of bleeder valve


You do not have to bleed them at all. Remove the cap off the master cylinder and you can then compress the caliber to remove the old pads and install new ones. No need to belled unless you replace the master cylinder or a caliber.

Oct 30, 2009 | 2005 Chevrolet Malibu

2 Answers

1999 Chevy Tahoe- Soft Brake Pedal


Try having the dealer flush and bleed your system. It is very hard to bleed ABS systems yourself and have safe brakes that still work afterward. Bleeding non-ABS brakes yourself is easy not the same for ABS brakes. Valving, sensors and what-not require a tech and the correct equipment in my opinion. You do it wrong and you could ruin your ABS system. Do that and see if they firm up. I replaced my brake shoes/pads at the same time all new everything in back, drums/springs everything and new rotors up front. then I had the chevy dealer flush, refill and bleed system. Stiffer pedal and brakes work better. Keep in mind the brakes on 99 Tahoes are inaedequate, require new rotors often, heat up and fade/glaze pads regularly. I replace my pads long before they wear down because they glaze up and start fading early. I'll rough em up once maybe, next time, new ones. Every two brake jobs, new rotors for me. Just how it is. They will stiffen a bit and work better but they will never be awesome brakes. Just how it is on 99 and earlier Tahoes. Hope it helps. Very important to bleed correctly though. I'll bleed my 83 Toyota 4x4 myself but not the Tahoe.

Aug 06, 2009 | 1999 Chevrolet Tahoe

1 Answer

2006 malibu maxx brakes problem...


Yes air gets into the hole system. You need to bleed all 4 wheels.

Jul 02, 2009 | 2006 Chevrolet Malibu Maxx

1 Answer

Changing brakes


You use a c-clamp to compress the piston. Don't remove the hose or you'll let air in.

May 16, 2009 | 1999 Chevrolet Malibu

2 Answers

Where is the bleeder valve on the 99 chevy malibu caliper


they are always on the top back of caliper.on inside,

May 16, 2009 | 2005 Chevrolet Malibu

Not finding what you are looking for?
1999 Chevrolet Malibu Logo

Related Topics:

179 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...