Question about 2003 Nissan Murano

Open Question

Murano doesn't start

2007 Nissan Murano not starting. After using remote to unlock door....Key is placed in ignition and turn to start. Battery, Oil light come on and sounds as though a computer ticking. After leaving the car and "re-arming"... the Murano horn does not honk as it normally would. All other power in the SUV is working...radio and such. What could the problem be?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 46 Answers

SOURCE: alarm wont shut off and I can't start vehicle

use the key and unlock the trunk...if that doesnt work do the passenger door...that should reset the alarm...

Posted on Jan 15, 2009

Ad
  • 9 Answers

SOURCE: Change settings so horn does not honk when arming via remote

If this is even possible...which im not sure..you would be best goin to a dealer..and let them show you how to use your alarm remote..the BUMs show do it for nuffin..Good luck

Posted on Jun 16, 2009

SOURCE: replaced the control arm for windshield wipers and

your horn wiring goes through the steering column then one wire goes to the horn and the other to power source

Posted on Sep 01, 2009

subikid90
  • 180 Answers

SOURCE: My horn went out on my 06 Nissan Murano. I'm

The horn doesn't use a fuse, instead it used a relay which is the large square black box you see in your fuse box. There should be one for your horn, blower motor (the blower that pushes the heat out the vents in your car) and a few other things.

Easiest way to see if it has gone bad is to switch the horn and blower motor relay and then try and use the horn and blower motor. If the horn works and the blower motor doesn't then you have a bad relay. You can go to any auto parts store and they will have them in stock.

Subikid90

Posted on Mar 03, 2010

  • 1 Answer

SOURCE: ignition key will not turn, 2007 Nissan Murano

I am having same trouble with 2006 Murano. Ignition will not turn electronically. Manual key won't turn either.

Posted on Mar 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 Nissan Murano won't start. No lights, no sound, nothing. Remote key also wouldn't unlock the car. Had to use another key that just unlocks the car. Please advise if you can. Thanks


So there is no power at all to the car? Check the battery and clamps on the battery. Clean them if you have to. Make sure battery is charged.

May 10, 2017 | Nissan Cars & Trucks

1 Answer

2005 Murano doors won't lock/unlock with remote or door switch... Would think it was an actuator if it was one door but all 4 try to work but don't seem to be getting enough power... There is no other...


try this put key in ignition turn to number 2. then press the fob. when the door lock press again to unlock them should work of from there. remeber to replace the battery in the fob first.

Oct 16, 2013 | 2005 Nissan Murano SL

2 Answers

Had the battery changed in 2007 nissan murano and now the chimes don't ring and the drivers doesn't automatically move back when opening the drivers door. How do I reset these?:


Disconnecting the battery erases stored memory,after you connect the battery put the key in the ignition cylinder and turn the driver door switch on(open) and off (closed), on (open),the entry,exist function then becomes complete, and the return operation can be operated,

Dec 30, 2012 | 2003 Nissan Murano

1 Answer

Passenger door and liftgate do not open with remote control or door panel control both start at the same time nissan murano 2005 s model


Liftgate is connected to front RH's door actuator thru back door's "opener switch". Replacing the passenger's door lock actuator will solve the problem.

Jul 25, 2010 | 2007 Nissan Murano SE

1 Answer

Battery went dead in 2007 Chevy Silverado truck. Now, remote does not work. Replaced battery in remote and it still does not work.


Make sure you have one working ignition key and all remotes for the vehicle.

1) Close all vehicle doors.
2) Insert the key into the ignition.
3) Hold down the power UNLOCK button on the driver’s door panel-continue to hold down until instructed to release in step 9.
4) Perform steps 5 through 8 in fairly rapid succession.
5) Turn the ignition switch to the ON position (as far as you can go without starting the engine).
6) Turn the ignition switch to the OFF position.
7) Turn the ignition switch to the ON position.
8) Turn the ignition switch to the OFF position.
9) Release the power unlock button on the door panel. The vehicle will lock and unlock the doors automatically.
10) Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the door locks and unlocks. This step may take up to 30 seconds.
11) Repeat step 10 NOW for each additional transmitter (including any existing transmitters).
12) Turn the ignition switch OFF then to the ON position in order to exit the transmitter programming mode.

Feb 28, 2010 | 2007 Chevrolet Silverado 1500 2WD

2 Answers

2003 Nissan Murano Driver door won't lock or unlock with keyfob


The key fob is the remote. But the remote type that works like a key. The remotes that you just need to carry on you to start the car or truck. That is a Key Fob.

Thanks Jay!

Jul 30, 2009 | 2005 Nissan Murano

1 Answer

My 2005 Nissan Murano seems to be possessed. The


Replace the remote battery first, then the remote.

Jul 03, 2009 | 2005 Nissan Murano

1 Answer

Ignition key will not turn, 2007 Nissan Murano


I am having same trouble with 2006 Murano. Ignition will not turn electronically. Manual key won't turn either.

Apr 10, 2009 | 2007 Nissan Murano SE

2 Answers

Nissan Murano 2005 SL keyless entry remote programing, got a used remote, how can I program it?


Close all vehicle doors, LOCK doors using drivers side switch.

Insert key all the way into the ignition, (do not turn) remove key.

Repeat this step 5 times. (6 total)

Hazards should flash to indicate program mode.

Press any button on transmitter to be programmed, hazards should flash to indicate successfull program.

*For additional remotes, cycle drivers door lock UNLOCK, LOCK, press any button on remote, hazards should flash. Repeat step as necessary.

Ignition ON, (engine off) ignition OFF, UNLOCK using drivers side switch, test remotes.

Source

Aug 06, 2008 | 2005 Nissan Murano

3 Answers

Key fob not working


hello mate.. if it has stopped working you might want to check the battery first.. if you are sure that the battery is fine then consider reprogramming the fob to your car.. here are the steps to follow.. NISSAN

Remote Control Fob Procedures:

The Central Door locking is controlled by the Multi-Remote Control system which controls
the door locking, door super locking and emergency hazard reminders.

When the doors are locked and unlocked the unit flashes the hazard lights once for lock and twice for unlock.

A maximum of four remote controls are allowed to be programmed:

ALMERA
ALMERA TINO
PRIMERA
MAXIMA
MICRA
SERENA
VANETTE CARGO
TERANO II

Ensure all the doors have been unlocked, either by using a good transponder key or remote
control plip key.

Procedure:
1. Turn the ignition switch from Position 0 to ON 6 times within 10 seconds.
2. Next, turn ignition switch to OFF position. Leave key in ignition switch.
3. Wait 2 seconds then the system will enter programming mode and will flash the warning
lights twice.
4. Press and HOLD the unlock button on the Plip.
5. While pressing the unlock button, press the lock button 3 times.
6. Release the unlock button.
7. The warning lights will flash once to indicate successful programming.
8. Repeat procedure 4 to 7 for up to 4 plip key's.
9. When completed turn ignition ON, and the warning lights will flash 2 times.
10. Remove key, and check all plip key's for operation.
NOTE : The programming mode will stop when either the ignition is switch ON, 4 plip keys
have been programmed or no input signal either from the switch or plip keys has been received
for 120 seconds.


http://www.autokeysquad.com/nissan-fob-programming



i hope this can help you.. :)

Jul 28, 2008 | 2005 Nissan Sentra

Not finding what you are looking for?
2003 Nissan Murano Logo

Related Topics:

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...