Question about 2004 Chrysler Town & Country

1 Answer

No instructions on how to remove rear wiper blade on 2004 Town & Country touring. The wiper arm only raises about three inches from window, and there is no indication of a normal wiper removal at that angle, is there?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 85 Answers

There is a plastic cap where the arm connects to a post. pop this cap off with your finger nail or small screw driver. this cap hides a nut. remove the nut (10mm socket needed?) and pull the arm off to replace the blade

Posted on Jun 17, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to take off the rear windsheild wiper on a 94 grand cherokee


You will need a 13-inch wiper blade for the rear window. 1 - When removing the wiper blade lift the wiper arm away from the window. ----- 2 - With one hand holding the wiper arm press the small tab on the underside of the wiper blade where it meets the wiper arm. ----- 3 - Slide the wiper blade off of the arm by pulling the center toward the bottom of the arm.----- 4 - Lightly lay the wiper arm on the window.----- 5 - Prepare your new wiper blade by taking the curved part of the plastic clip and line it up with the curve of your wiper arm. ----- 6 - Lift the wiper arm and press it through the center of the wiper blade up and over the plastic clip. 7 - Pull the wiper blade up until it clicks. Place the arm back on the window.

Jan 11, 2012 | 1994 Jeep Grand Cherokee

1 Answer

I have a 2007 Town and County. The rear wiper is not touching window by about 1/4 inch. I can press it back down but it will not stay once you turn on the wiper. How can I fix this problem?


If it is not touching the glass the arm is bent. Raise the arm away from the glass. Grasp the arm near where it is mounted to the body and near the wiper blade with the other hand. Slightly bend the arm toward the glass. Only bend the arm a very slight amount and check to see if there is enough pressure for the wiper blade to work correctly. Repeat this until the wiper blade cleans the glass properly. DO NOT over bend the wiper arm as too much pressure will cause the blade to wear out very quickly.

Dec 22, 2010 | 2006 Chrysler Town & Country

1 Answer

The wiper blades are overlapping on Chrysler Town & Country, 2002. What is the problem?


Remove the wiper arm or arms,and reinstall where
they are supposed to be.
Who put them on wrong.

Dec 01, 2010 | 2002 Chrysler Town & Country

1 Answer

Need to change the rear window wiper blade on a 2003 tOWN & cOUNTRY CHRYSLER VAN


Take it to your local Auto Zone-we change them for you if you are buying the blades from us. You MIGHT find someone to do it for you even if you did not buy them at AZ.

Mar 10, 2010 | 2003 Chrysler Town & Country

3 Answers

How easy is it to replace the front wiper motor on a 2004 ford escape ? Where is it located ?



Front Wiper Motor
Removal & Installation

NOTE A new wiper motor assembly comes with the linkage arm installed.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the windshield wiper mounting arm and pivot shaft
    WARNING Do not remove the wiper motor linkage arm from the wiper motor assembly. If the arm is removed, the wiper arms may not park in the correct location.
    NOTE Use a suitable tool to separate the wiper linkage arm from the wiper mounting arm and pivot shaft assembly.
  3. Remove the 3 bolts and the wiper motor.

    7f7866e.gif

    Fig. Wiper motor and linkage

To install:
  1. Install wiper motor and bolts.
  2. Tighten wiper motor bolts to 10 ft. lbs. (13 Nm).
  3. Install windshield wiper mounting arm and pivot shaft.
  4. Check wiper operation.

Rear Wiper Motor
- Removal & Installation
  1. Remove the rear pivot arm.
  2. Remove the rear wiper motor shaft nut cover
  3. Remove the rear wiper motor shaft nut.
  4. Open the lift gate window.
  5. Remove the rear wiper motor cover trim panel.
  6. Disconnect the electrical connector.
  7. Remove the 2 rear window wiper motor nuts
  8. Remove the rear window wiper motor.

    79be491.jpg
    Fig. Rear wiper motor view-2008 model shown, other years similar

To install:
  1. Install rear wiper motor and tighten mounting nuts to 62 inch lbs. (7 Nm).
  2. Reconnect the electrical connector.
  3. Install wiper motor cover trim panel.
  4. Install rear wiper pivot arm tighten nut to 53 inch lbs. (6 Nm).
  5. Install shaft nut cover.
  6. Check wiper operation.

Good luck (remember rated this post).

Feb 25, 2010 | 2004 Ford Escape

1 Answer

Rear windshield wiper blade doesn't hit rear window on 2006 Chrysler Town & Country Van


the pivot pin must be rusted to the point it does not want to move, try lubing it with wd40 or equivalent lube,at the bottom of the wiper arm just before the bolt that holds it to the car is the pivot point.that's where it has to be lubed.

Jan 18, 2010 | 2006 Dodge Grand Caravan

1 Answer

How do you get the wiper blade from the arm to


Push the tab up & the blade slides inward. Most auto stores will change the blades for FREE if bought there.

Jan 08, 2010 | 2003 Chrysler Town & Country

1 Answer

Front windshield wipers are crashing into each other


Yes you can adjust them yourself. First you need to check that the wiper arms are not bent. If not, remove the cap at the wiper arm base, under it u will find a nut, remove this nut. you should now be able to remove the wiper arm. (it is comon for caravan wiper arms to be corroded on. If the arm dosen't come off, you may need to heat up the wiper arm with a propane torch. be careful not to melt the plastic cowel under the arm. OR you can use a wiper puller or a battery puller. do not force it, you can break the arm, DO NOT PRY AGAINST THE COWEL OR WINDSHIELD.
Once both arms are off, turn your van on and turn the wipers on. watch the wiper posts, turn the wipers off and watch the wiper posts return and stop in the "parked" position. Turn the van off. Install the passanger wiper arm first, it is positioned closest to the bottom an inch or two above the black cowel. It should be parrallel to the cowel. next install the drivers side wiper arm. it is positioned about 4 inches above the passanger wiper. again running parrallel to the cowel and passanger wiper. tighten the lock nuts down (do not over tighten) wet down your windshield with glass cleaner or windshield washer fluid and test wipers. If they still hit you can lower the passanger one a little or raise the drivers one a little (careful you don't raise the drivers one too much or it will 'jump' off the windshield at the top of the wipe).
good luck, hope this helps.

Nov 23, 2009 | 2001 Chrysler Town & Country

1 Answer

How to replace the wiper insert at the back of


moz-screenshot.jpg
  1. REMOVE RR WIPER BLADE
    1. Raise the rear wiper blade to the position as shown in the illustration where the meshing of the claw disengages with a clicking sound. NOTE: Be careful not to break the claw.
    2. Pull straight the rear wiper blade to vehicle's left from the wiper arm. NOTE: Do not fold the rear wiper arm with the rear wiper blade removed from it.1722d05.gif

  1. REMOVE REAR WIPER RUBBER
    1. Place the rear wiper with the rear end of the rubber protruded from the blade stopper as shown in the illustration. NOTE: Do not pull out the wiper rubber forcibly, as the backing plates will become deformed or the blade claws will become damaged. HINT: The rubber can be easily pulled out by pushing the middle area of the blade.
f54b10a.gif
  1. INSTALL REAR WIPER RUBBER
    1. Install the 2 wiper rubber backing plates to the rear wiper rubber. NOTE: Be careful to observe and keep direction of curvature for correct replacement.
0dd144d.gif
b. Insert the rear wiper rubber from the claw of the middle of the rear wiper blade into the rear end position.
8f40009.gif
c. After passing the rear wiper rubber through the rear end side claw, protrude it from the rear end stopper and pass it through the front tip side claw.

Sep 12, 2009 | 2005 Toyota Matrix

1 Answer

My 2001 Town and Country's rear windshield wiper motor is kaput. How do I change it without destroying the rear tailgate paneling


Pretty straight forward.....here are the steps:

Please don't forget to rate--

Rear Window Wiper Motor Removal & Installation To Remove:
  1. Disconnect and isolate the negative battery cable.
  2. Remove the rear wiper arm.
  3. Open the liftgate.
  4. Perform the following to remove the liftgate trim panel.
    • If equipped, remove the lift motor link
    • Remove the upper frame molding
    • Remove assist handle screws
    • Disengage the hidden clips around perimeter of liftgate trim
    • Disconnect the electrical connectors.
  5. Disconnect the wire connector from the wiper motor.
  6. Remove the wiper motor mounting screws.
  7. Remove the wiper motor.
To Install:
  1. Position the wiper motor in the liftgate.
  2. Install the wiper motor mounting screws.
  3. Connect the wiring connector.
  4. Install the liftgate trim panel.
  5. Close the liftgate.

Jul 24, 2009 | 2001 Chrysler Town & Country

Not finding what you are looking for?
Cars & Trucks Logo

592 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...