Question about 2003 Ford Crown Victoria

3 Answers

Where is fuelpump on 2003 crown vic police intercepter

Where is the fuel pump on the 2003 crown vic. police intercepter, and how do you change it.

Posted by on

  • Anonymous Mar 23, 2014

    Back lights work but the brake lights don't for a 06 crown Vic police car

×

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Dear cdkkks,

Replacing a fuel pump in modern cars requires some preliminary electrical, fuel test analysis work. I have noted some professionals indicating you need to run car until gas lines, tank is empty; more than likely, if your fuel pump is defective, you cannot start the car, car is unoperative; you will attempt to start car, starter will turn the engine over rapidly without starting, let's assume you are in this condition.

First we need to test the fuses and fuel pump relay, basically the electrical opportunities on your vehicle, the relay panel is on the fender well, driver side, lift the relay control assembly from the fuse center and press the tab on the end, push down and this will release relays from the cover. This relay control panel includes the PCM power relay (left side in original position) Fuel pump relay (Center) this is the relay you are concerned with and the Air Conditioning relay on (Right). If you have friends, or associates who have electrical equipment to test the fuel pump relay, utilize their help, some automotive shops will provide this service. Checking the relay circuit with a jumper wire, any scrap piece of wire, 16-18 gauge will do; as you are looking directly down at the relay opening, you will note an opening at the 6:00 and 12:00 clock positions, 6:00 is the positive, 12:00 is the neutral, volt meter set for volts will confirm. Open the gas cap from the fuel tank filler pipe, insert the jumper wire and carefully listen for a whirring sound. If there is no sound and you have confirm electrical pump fuses, fuel pump relay is working properly (Voltage is pressure, battery voltage and slightly less voltage at the relay circuit when ignition key is turned on) then we have couple more checks to perform before we replace fuel pump. Let's check the fuel rail pressure on your Ford Crown Vic, obtain a fuel compression gauge with a Ford Schrader valve adapter, check to verify that no fuel pressure exists. If "NO" fuel pressure exists, and we have confirmed the voltage integrity of relay/fuel pump circuit, then we are ready to remove fuel pump. Use a simple gas siphoning kits from your local auto parts outlets to safely remove all remaining gas from gas tank, use appropriate gas tanks to store fuel; safety is the key here, gas and gas fumes are extremely dangerous; use appropriate chemical/gas gloves when siphoning/handling gas.

(A) Park your Crown Vic, perferably in a garage, concrete floor and make sure there is enough room around the back of the vehicle for you to work and move tools around.

(B) Raise the back of your car using a floor jack and support it safely on wheel/jack stands; remember, the driver side rear wheel must be removed in order to remove the fuel tank filler pipe, place your wheel stand (supplement with 2 by material for proper height on frame,slightly forward of rear wheel); safety is the key issue here and I cannot overly emphasize this issue, heavy wheel stands should be supporting the right rear wheel and frame, slightly forward of rear wheel, driver side).

(C) Disconnect the fuel tank filler pipe and the fuel pump connector located above the cross member underneath the vehicle, you must remove the (3) screws on the topside (fuel tank fiiler pipe) and approximately (4) screws on the bottom side, and the (1) screw adapter plate where the fuel tank filler pipe is inserted into the gas tank, top of wheel opening, underneath the vehicle. After these connections are removed, push the fuel tank filler pipe further into the fuel tank, allowing you additional room to lower the filler pipe from it's current position, downward; once you have sufficient clearance, twist, turn left, slightly back and forth movements and carefully pull outward, removing the filler pipe from gas tank. Do not damage the rubber groment in gas tank as you remove the filler pipe. As a note, when you reinstall the filler pipe, insert small amount of vasoline on filler pipe end that is inserted into the gas tank to facilitate the installation process.

(D) Support the fuel tank with a jack and remove the nuts from the holding strap using a wrench or ratchet and socket. Move the strap away and slightly lower the fuel tank in order to disconnect the vapor tube from the tee connector on the right and the vapor line from the canister tube. Discard the fuel tank mounting studs and replace with new fuel tank mounting studs on the reinstallation process.

(E) Unplug the pressure transducer electrical connector located on the top rear corner of the fuel tank.

(F) Clean area around the mounting fuel pump mounting flange. Remove/disconnect the fuel lines attached to fuel pump mounting flange then remove the fuel pump mounting flange mounting bolts in a crisscross pattern.

(G) Lift the fuel pump assembly off the tank. Replace the new fuel pump in the assembly and install the assembly in the tank. Install the flange screws and torque to approximately 89 inch lbs using a crisscross pattern. If no torque wrench is available, tighten to a snug fit and stop.

(H) Afterwards, raise the fuel tank enough to attach fuel lines and vapor lines indicated above, item D. After connecting all lines, raise tank with floor jack to its original position "carefully" and utilize the new mounting bolts, securing straps in their original position and torque bolts to approximatlely 25-30 lbs torque.

(I) Install the fuel tank filler pipe per the aforementiond process reversed.

(J) Review your connections and then carefully lower the vehicle, use a gas container, input 4-5 gallows of gas and start the engine and check for leaks.

Wishing you the very best,

drprice

Posted on May 20, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Can you replace a fuel pump from a 2000 Crown Victoria with out removing the gas tank

Posted on Nov 14, 2011

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 74 Answers

Should be in the fuel tank

Posted on May 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have p1747 code will that lite up the red light top right corner of my dash on a 2000 crown viv police intercepter


That is a transmission code...

P1747 (EPC Shift Solenoid). Not uncommon for police interceptors...

Here is a discussion of other possible causes:

http://towtalk.net/forum/topic/2000-Crown-Vic-Police-Interceptor-.htm

May 13, 2015 | Cars & Trucks

3 Answers

Crown vic 2005 no start replaced fuel pump


check your crankshaft position sensor. fuel+spark+compression+timing=ignition.

Mar 13, 2014 | Cars & Trucks

1 Answer

I have a 2003 police intercepter crown vic. the trans slipping when I take off.


have you checked the transmission fluid? car should be on level ground with car running.

Sep 07, 2012 | Cars & Trucks

1 Answer

2003 CROWN VIC HAS NO SPARK AND NO POWER TO FUEL PUMP CHECKED RELAYS AND FUSES CHANGED CRANK AND CAM SESOR LOOKED FOR BAD GROUND AND BROKEN WIRES AND HELP PLEASE


DID YOU CHECK THE FUEL PUMP SHUTOFF SAFETY SWITCH ON THE LH/DRIVERS SIDE IN THE TRUNK & MAKE SURE IT IS DOWN ,& EVEN IF IT IS SOMETIMES YOU CAN TAKE SOMETHING & PUSH IT UP & THEN PUSH IT BACK DOWN & IT WILL CRANK,& BELOW THAT SWITCH IN THE TRUNK IS A FUEL PUMP DRIVER MODULE ,IT MAY BE BAD,THOSE ARE A COUPLE OF THINGS THAT HAVE WORKED FOR ME ,& THATS PRETTY MUCH ALL I DO IS WORK ON FORDS, & LX CROWN VICS & P71 POLICE CROWN VICS WHERE I AM WORKING, HOPE THAT IT MIGHT HELP YOU FIX IT. SEAN

Nov 02, 2009 | 2003 Ford Crown Victoria

3 Answers

Does the crown vic police intercepter take as much oil as the regular crown vic? (when changing the oil and filter)


I ~think~ the 1999 is the same as the 2000 (mine is a 2000 P71)

The 2000 CVPI (Crown Vic Police Interceptor) owners manual recommends the following:

Engine Oil - Motorcraft SAE 5W-30 Super Premium Motor Oil 5.0 quarts

Transmission Fluid - Motorcraft Mercon V ATF 13.9 quarts (fluids Mercon & Mercon V are NOT INTERCHANGEABLE, DO NOT MIX)

Fuel Tank - 19.0 gallons

Break Fluid - DOT 3


Rear Axle Lubricant - Motorcraft 80W-90 Premium Rear Axle Lubricant 3.75 pints (add 4 oz of Additive Friction Modifier C8AZ-19B546-A or equilavent meeting Ford Spec. EST-M2C118-A for complete refill of Traction-Lok Rear Axles)

Engine Data - 4.6L V8 Engine
Cubic Inches - 281
Required Fuel - 87 Octane
Firing Order - 1-3-7-2-6-5-4-8
Spark Plug Gap - 1.3-1.4 mm (0.052-0.056 inch)
Ignition System - Coil On Plug
Compression Ratio - 10.0:1

I hope this helps!

Jun 27, 2009 | 1999 Ford Crown Victoria

1 Answer

Pulsing feel to right in steering wheel on hard left-hand turns.


What rims are on the car the steel police ones and what tires are on it could be hitting the stops on the frame and where the proper bolts put back in on the rack mounts and did you go with the heavy rack for the police car .Cause when I built them there was an issue with the proper bolts and there was a different rack for the cop cars the to the basic crown vic do to the suspension upgrade on it and the diffrent pump

Mar 12, 2009 | 2003 Ford Crown Victoria

Not finding what you are looking for?
2003 Ford Crown Victoria Logo

2,977 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...