Question about 2000 Jeep Grand Cherokee

1 Answer

How do I replace a front wheel bearing assembly on a 2000 jeep grand cherokee?

Posted by on

  • djeiii May 17, 2009

    Thanks for the help, it worked.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

Remove tire, brake caliper and rotor (before doing this use a solid breaker bar and a long steel pipe to remove center nut on axle) It is tight (about 170lbs) Once everything is off, put the nut on the axle backweards and make it even with end. give it a tap with a hammer to break it free from the bearing splines. There are three 12point bolts on the backside of the steering knuckle. back them out a bit and use a chisel between the bearing and knuckle to get it free. Use lots of wd40 or other solvent. If you need to, hammer a bit on three bolts.But not so much you can't get a wrench on them. as bearing becomes free, remove bolts and finish. Assemble in oposite order (but no hammering) when tightening axle nut use # I gave you and do not loosen to get cotter pin through hole...tighten further.

Posted on May 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front wheel s making humming noise


sounds like a wheel bearing assembly to me. i would have the clearance checked at a jeep dealer. if you can rock the wheel gently while moving forward and the sound fades and comes back, definitely a wheel bearing assembly.

Nov 14, 2013 | 2004 Jeep Grand Cherokee

1 Answer

Replace Front Wheel Hub Bearing 2002 Jeep Grand Cherokee 2 wheel drive


Removal
  1. Raise and support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the brake caliper, caliper anchor, rotor and ABS wheel speed sensor.
  4. Remove the cotter pin, nut retainer and axle hub nut.
  5. Remove the hub/bearing mounting bolts from the back of the steering knuckle. Remove hub/bearing from the steering knuckle and off the axle shaft.
Installation
  1. Install the hub/bearing to the knuckle.
  2. Install the hub/bearing-to-knuckle bolts and tighten to specification.
  3. Install the hub washer and nut. Tighten the hub nut to specification. Install the nut retainer and a new cotter pin.
  4. Install the brake rotor, caliper anchor, caliper and ABS wheel speed sensor.
  5. Install the wheel and tire assembly.
  6. Remove the support and lower the vehicle.

Apr 22, 2012 | 2002 Jeep Grand Cherokee

2 Answers

2006 Jeep Grand Cherokee grinding while steering


I'd bet your brake rotors are grooved and need to be resurfaced (or replaced if they are too thin). This also means you should replace the pads too.

Apr 03, 2010 | 2006 Jeep Grand Cherokee

1 Answer

2005 Grand Cherokee grinding


The Wheel Bearing(s) need to be replaced. They should be bolt-on assembly and are bolted from the back of the steering knuckle. It is easy to remove and replace. Buy your bearing assembly(ies) from an auto parts store versus the dealer to save you a lot of money.

Dec 23, 2009 | 2005 Jeep Grand Cherokee

2 Answers

Oscilating humming coming from left front wheel


SOUNDS LIKE YOU HAVE BAD LF WHEEL BEARING..JACK UP FRONT OF VEHICLE..BLOCK REAR WHEELS..PUT TRANSFER CASE IN NEUTRAL,SPIN EACH FRONT WHEEL BY HAND WITH OTHER HAND ON COIL SPRING..YOU SHOULD FEEL ROUGHNESS IN SPRING ON SIDE THAT HAS BAD BEARING..IT IS A HUB/BEARING ASSEMBLY

Jul 23, 2009 | 2002 Jeep Grand Cherokee

1 Answer

How do replace front axle bearings on a 92 jeep


You have to pull off the wheel, brake assembly, and rotor. If it is a 4x4, i suggest you take it to a mechanic. If it isn't, once you pull all that off you will see a little cap cover. take a small screwdriver and pop off the cap. There will be a clip. pull off the clip and pull out the axle bearing. Make sure you grease the axle bearings before you put the new one in. Then put it back together in the reverse of these instructions. Hope this helps.

Apr 30, 2009 | 1995 Jeep Grand Cherokee

1 Answer

RELACING WHEEL BEARINGS IN A 95 JEEP GRAND


Front wheel bearings can be done at home rear wheel bearings will require a hydraulic press and an axle puller. Either job can be difficult depending on amount of rust and availability of tools. The front wheel bearings are an assembly and once the jeep is up on jack stands, with the tires, brake calipers, and rotors removed, it is only a matter of removing the axle nut and 3 bolts (which can be difficult depending on rust) holding in the old bearing assembly

Feb 22, 2009 | 1995 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

232 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...