Question about 1990 Mazda MX-5

1 Answer

To much slack on the cable when i lower window causing the cable to part with the motor

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 3,113 Answers

Get a new window regulator.

Posted on May 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Electric handbrake motor seized solid,how to replace motor on S type 2005 v6


Electronic Parking Brake EPB Jaguar Type 2004
The parking brake motor sits sideways just above the differential. The differential actually has to be lowered to get it out. I climbed under my S and lubed the cables up with silicon lube before the weather got bad.
When a new motor is fitted, set up the hand brake slack.

Dec 02, 2017 | Cars & Trucks

1 Answer

Nissan bluebird front window adjustments as the window gose up then down abit when you close it please how do i fix it


Not being familiar with a non US Nissan I can only guess that it is similar in how the window israised and lowered. The US version uses a single track in the center of the door which a nylon guide rides on. The window is raised and lowered via a cable driven by an electric motor which winds the cable in one direction or rhe other. Sometimes the guides get dry whic will cause the window to be a little slower going up and sometimes at an angle al little bit. Also the guides that the window slides in can get a little dry. If you use a silocon spyay, this may resolve your probleem. The center guide also can be moved a little to the front or back at the mounting points which may have eenough slack in them for you to rock the center guide at an angle tilting it to the front or back (from the top or bottom) this can also assist you, if there is enough slack in the mounting holes where the bolts go through. Good luck

May 01, 2014 | 2002 Nissan Bluebird

2 Answers

2005 cavalier regulator not functioning to lower front driver side window. window is in up position. cannot hear motor engaging to lower window when switch is depressed/activated. sounds activated to...


If the motor and regulator both work fine or sound like they are engaging when your try to raise the window,but you hear nothing when you try to lower the window then I think it is a pretty safe bet to say your switch is bad.

Sep 17, 2011 | 2005 Chevrolet Cavalier

1 Answer

Need to replace my started on a 1994 S10 Blazer. I have it loose from the motor but can't get it out. Any suggestions?


YOU HAVE TO REMOVE POSITIVE BATTERY CABLE AT THE BATTERY TO GIVE YOU ENOUGH SLACK TO LOWER STARTER.ALSO YOU HAVE A BRACE OR BRACKET HOLDING STARTER AT THE REAR IN PLACE MAKING HARD TO GET OUT.

Jun 07, 2010 | Chevrolet Blazer Cars & Trucks

1 Answer

Window goes up but wont come down cables are slack and the motor runs


there are little clips on the bottom of the window that are glued from the factory. sounds like your clips may have come loose

Mar 02, 2010 | 2000 Buick Century

1 Answer

Driver side power window stop working


it is a chrysler so my guess would be the window motor if that dont fix it then your wires riped out the harness so replace the wires and give them more slack this time cause chrysler dont give any room for error

Dec 11, 2009 | 1998 Chrysler Cirrus

1 Answer

Trying to figure out how to rewind the cable correctly on the right rear window regulator,I seem to have just one more time around the regulator cable pulley,but i cant figure out how to get it to track...


Those regulators are not designed to be repaired -- only replaced. The cable spool, pullys and cable are installed as complete components -- the slack is taken out of the cable during assemby at the manufacturer.

Jun 10, 2009 | Hyundai Motor 2004 Accent

1 Answer

1997 Nissan Altima Driver Power Window


Then power window regulator cable is snapped out its place ,you need to install new power window regulator for the door to fix this issue ...


Good luck...

Nov 06, 2008 | 1993 Nissan Altima

1 Answer

Passenger side window


get the complete panel other wise you just end up with window doing everything apart from work properly,put you motor in new panel and you be well happy..

Oct 03, 2008 | 2005 Volkswagen New Beetle Convertible

Not finding what you are looking for?
1990 Mazda MX-5 Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8572 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...