Question about 2002 Volvo S60

1 Answer

Where is thermostat can it be changed using axle stands

Volvo s60 2t where is the thermostat and can it be changed using alxe stands if needed

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 1 Answer

The thermostat is attached to the radiator. I don't know why you'd want axle stands.

Posted on May 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What do you have to take off to get the alxe out of a 1998 olds 88


Tire, Caliper and bracket, tie rod to spindle, lower strut bolts, remove brake caliper hose from bracket on strut, remove axle nut, Pull spindle away from strut, push axle out of hub, use pry bar and pop axle from Tranny. Make sure when you reinstall axle into tranny your careful not to rip tranny axle seal.Make sure it is fully seated also.

Nov 07, 2014 | Cars & Trucks

1 Answer

How to replace thermostat in 1999 volvo


Don't just change just the thermostat... change the sensor located in the thermostat housing (if your engine is overheating). The whole works is located inside the timing cover. Sockets: You'll need a 10mm for the timing cover and the 3 bolts on the thermostat cover, and an 8mm for the sensor harness bolts. Then you'll need a 3/4 open end wrench for the sensor.

Jun 22, 2014 | 1999 Volvo S80

1 Answer

How do i replace the leaf springs on my 1978 ford f100


Jack the vehicle up and place on jack stands. Remove the rear wheels. Remove the large u bolts holding the springs to the axle. support the axle with a jack. Do 1 side at a time. Now unbolt the springs at either end. Remove and install the new spring

May 18, 2014 | Ford Cars & Trucks

1 Answer

Jack points on 2004 Volvo S80 to change oil?


As always use extreme caution when lifting vehicle, but I have found that the easiest way to lift my car for oil change is to put jack under the cross member under engine.

Jan 20, 2010 | 2004 Volvo S60

2 Answers

Remove rear axles 99 montero sport


Go to this link for your info...you didn't mention 4WD...but this has a breadown and diagram for you.

Oct 08, 2009 | 1999 Mitsubishi Montero Sport

1 Answer

05 crown victoria police package rear axle removal


there are two main designs. One uses a bearing and flange at the backing plate area, release that and you can pull the axle and bearing.

the Other design is call a c lock axle. Inside the carrier, there are 4 spider gears. Two are splined to the alxes and two idle on an idler shaft. Remove this shaft, and then you can push the axle shaft inwards about an inch or so.

this will allow you to remove the c shaped retainer that is engauged with a groove at the inboard end of the axle.

So, now the bad news: often the c lock axle uses the axle shaft itself and the inside bearing race...which means if the bearing has failed, you need to replace the axle also.... Inspect carefully. Metal temper is the issue and once that is comprimised, you need to replace.

Doc

Sep 19, 2009 | 2005 Ford Crown Victoria

2 Answers

Dealership says axle needs to be replaced


Not unless you want to die in a head on smash with a truck.

If front suspension seizes then you will swerve to one side , you may hit the sidewalk or the truck , take your pick

Aug 24, 2009 | 2000 Volvo V40

1 Answer

Noise when driving starts from 30 mph.. when turn wheel to left on the interstate, the noise becomes louder. Change left axle the noice didn't go away... also leaks around the axles, and from power...


sounds like powersteering pump. put it in park and open hood. have someone stand in front of engine near powersteering pump and put hand on it to feel vibration. MAKE SURE CAR IS IN PARK. Rev engine to about 2200 Rpm's and see if I am correct. Thanks and Good luck

Mar 18, 2009 | 1999 Volvo S80

1 Answer

Tools needed to change brakes


Hi

Pair of rubber gloves, Jack, 2 axle stands, Socket set, Pliers, Screwdrivers, Brake cleaner, Kitchen roll, Lead lamp or torch.

Good Luck !

Remember to pump the brake pedal, before you drive off, otherwise you will be doing body repairs next !

Please give me a FixYa rating please.....I want to be a Guru !

John.

Feb 04, 2009 | 2004 Volvo S40

1 Answer

2005 Yukon Front Diff Axle seals


You don't have to remove the whole diff to change the seals, but you will have to seperate it where the shaft meets the carrier housing. There is a clip holding the passenger axle shaft in place that you have to remove to change the seal. The drivers side axle stub can be removed with a little force as there is a spring clip holding that side in.

Sep 01, 2008 | 2003 GMC Yukon

Not finding what you are looking for?
2002 Volvo S60 Logo

Related Topics:

222 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...