Question about 1988 Mazda B2600 Cab Plus

1 Answer

Hand brake adjustment on 1994 b2600 4x4 its loose and does not work at all

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 62 Answers

First thing to do is to take a look at the rear brakes and make sure there in good working order and adjusted properly.
then there is an adjustment in the cable ware the 2 cables from the rear brakes meet the cable coming from the cab

Posted on May 16, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Changed rear brakes on 2004 kia spectra put new caliper on passenger side and pads on both sides now driver rear looked up and passenger side wont do anything

You may need to adjust the cable for your hand brake. The driver's side is too tight and the passenger side is too loose. Best thing to do is drop the hand brake (e-brake) down, loosen the adjuster on the drum, then lift the hand brake until you hear 5 clicks. Then adjust the handbrake cable on both sides until the disk just stops.

Dec 09, 2013 | Cadillac DeVille Cars & Trucks

1 Answer

I tired to get my car inspected today put the told me they could not because of the emerency brake but could u tell me what it could me

Your rear brakes are probably in need of adjustment. Try to pull the hand brake around twenty times to adjust the rear brakes.If this does not work then you will need to check your star wheel adjustment screw. It could be frozen and need to be sprayed with something like sea foam or something else. The rear brakes should be fine if your inspector did not alert you that they are worn out

Aug 24, 2011 | 1994 Toyota Camry

1 Answer

Having trouble replacing rear brake pads on a 1994 Lincoln Conntinental. Purchased a special tool to conpress the wheel cylinder. Left hand threads? Tried right handed and no luck. Please help!

The tool only turns in the parking brake adjuster
You still have to push the piston in.

Open the bleeder valve
You have to flush the system on ALL
vehicles every 2 years anyway.

May 21, 2011 | 1994 Lincoln Continental

1 Answer

Hand brake not working moves up and down and does not assist with brake holding

You may have the brakes out of adjustment or a broken ebrake cable, the first thing is to go under the truck and have someone apply the e-brake and see if both rear cables are pulling. im not sure if you have drum or disc in the rear of this jeep but they both use cables, if the cables are working then you will need to remove the wheels and check the brakes, the brakes may be worn or out of adjustment.hope this helps.

Mar 10, 2011 | 1994 Jeep Cherokee

1 Answer

My brake lights in my 1994 Buick Regal Gran Sport stopped working

Brake light switch. Should be against brake pedal arm under dash. May be loose or need adjusting.

Mar 27, 2010 | 1994 Buick Regal Gran Sport

2 Answers


I recommend you get a Haynes repair manual on your vehicle as there are several adjustments you may need to look at. If this is the first time you have had this problem and have less than 50,000 miles on the brake pads then it is most likely the cable and there are a couple of places to adjust in most cases. If you have 50,000 or more miles on those read pads you may need to replace the rear brake pads. The manual will help you in doing this repair correctly.

Nov 20, 2009 | 2004 Toyota Matrix

3 Answers

Need Fuse Diagrams, Brake light stays on

they are printed inside fuse panels and check brake light switch follow brake pedal under dash

Oct 25, 2009 | 1994 Nissan Sentra 4-Door

1 Answer

How do I adjust the hand brake?

The adjustment is under the brake handle inside the center console.

BUT.....most of the time the emergency brake is loose is because the brakes are worn down or the automatic adjusters aren't working.

So before you go to all of the trouble of adjusting the emergency brake you may want to check the wear on the rear brake pads.

Jul 07, 2009 | 1986 Suzuki Samurai

1 Answer

Bmw 320 hand brake not functioning properly

either the hand brake needs to be adjusted or the rear brake shoes , which are inside the rear discs are worn not allowing the hand brake to work

Mar 22, 2009 | 1997 BMW 5 Series

1 Answer

1994 lincoln continental executive series

have you replace the caliper? if you did then when you stop loose the bleder of the caliper and if pressure come out tie the bleeder again and haved your mechanic remove the brake master cylinder and see if there is any adjustment for the push rod or shaft behinf the master cilinder and loose the adjustment to make it short but if there is no adjustment then leave the master little loose and if this take care of it you might have a wrong master installed or just need to adjust the rod behind master good luck

Jun 02, 2008 | 1994 Lincoln Continental

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

351 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts


Level 3 Expert

79186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides