Question about 1988 Ford Ranger

1 Answer

My 93 ranger will not go into wheel drive when the button is mashed.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 62 Answers

Im assuming you mean 4 wheel drive?
check the fuses
there is a common problem with the transfer case shift motor going bad on this model

Posted on May 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a F350 4WD truck, but I do not know which button engages the 4x4. Please help


It is easily done..There aren't that many buttons..Apparently the indicator is worn off the button....Set parking brake,start truck and put it into neutral...mash each button one at a time slowly after you mash the 4 wheel drive button you will see an orange light in your dash gauge area near the bottom light up and tell you 4wheel drive has been engaged....

Feb 21, 2015 | 2005 Ford F 350 Super Duty

1 Answer

Ford ranger 93 rear wheel abs equipped ! My pedal was going 2 the floor so I changed booster and nothing then the master cyl and my pedal is hard but I have brakes! After I bled the rear wheels and the...


Don't worry about it until you drive the truck. Complete the brake bleeding then drive it. If it stays on then you are going to have to have the codes pulled

Mar 31, 2013 | Cars & Trucks

1 Answer

Wiper problem-93 Ford Ranger XLT,2 wheel drive,3.0 v-6.auto. Only have high speed,no more intermitent,no longer returns to start position-HELP


probably the motor but chaeck this first G3 CHECK CIRCUIT 58 FOR BATTERY VOLTAGE
  • Unplug wire harness connector.
  • Set wiper switch on low.
  • Check Circuit 58 for battery voltage key on.

    k17829a.gif

arrow.gifVoltage OK
CHECK for malfunctioning wiper motor. Perform low speed current draw test. SERVICE as required.
arrow.gifVoltage not OK
CHECK for:
  • Open connector.
  • Malfunctioning switch.
  • Malfunctioning governor.
  • Open wire Circuit 58 (W).

Jun 02, 2010 | 1993 Ford Ranger SuperCab

1 Answer

4wheel drive issues


There is a small servo motor on front axle, Check the connections, also check connections on switch. May need to check for voltage to servo motor they often burn out.

May 16, 2009 | 1988 Ford Ranger

1 Answer

I just purchased a 1994 ford ranger with 125,000 miles and runs great until last night when i had to engage the four wheel drive.It made a bad clunk and whining noise for some time and now i can hit the...


It sounds like the electric motor for the 4 wheel drive may not be engaging. It could also be the magnetic clutch for the 4 wheel drive may not be working. This sounds like an electrical problem.

Apr 27, 2009 | 1994 Ford Ranger Supercab

1 Answer

PUSH BUTTON FOUR WHEEL DRIVE FORD RANGER NOT WORKING


the transfer case is sticking from non use, change the lube in the case ( Ford ATF) and drive it for awhile it should be ok then.

Apr 07, 2009 | 1988 Ford Ranger

1 Answer

88 4x4 ranger won't go into 4x4


check to see if the drive shaft is turning if so the problem is with the hubs or differnal

Mar 02, 2009 | 1988 Ford Ranger

1 Answer

1999 ford ranger 4 wheel drive 5 speed won't start


i had a 93 ranger, same thing happend to me. Ended up it was the little switch on the cluch pedal. when they pushed the clutch in their foot kicked it off. Its just a clip on spring on the arm of the pedal.

Jan 03, 2009 | 1999 Ford Ranger SuperCab

1 Answer

1993 FORD RANGER 4 WHEEL DRIVE


there is an actuator on the back of the transfer case that likes to fail odds are this is where your problem is. check power and ground here and if you have both replace the actuator

Nov 22, 2008 | 1993 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...