Question about 1984 Chevrolet Corvette

1 Answer

How to remove ignition switch . need diagram. or to get to the release

How to remove ingintion switch, how do you release the ignition switch.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 47 Answers

You need to put the key in the ing and turn the key backwords and pull out at the same time usally that will drop it out there might be a pin hole in it if so put a pin in there to release the lock on it

Posted on May 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Key will not remove from ingintion switch


Try pushing the gear shift further forward in park with your hand and see if the key releases.

If this fails it may be the switch itself just under the centre console which surrounds your gear shift. Carefully but firmly pull up the centre console up and you will see a little 'plunger' switch the engages when the gear shift is at its furthest travel forward in park.

Mar 04, 2011 | 2001 Mercedes-Benz CLK-Class

1 Answer

How do I reset "Maint


First open your ingintion and make sure dash reads odometer, then close ignition press and hold trip-odometer buttom open ignition odometer read out will show --------------- flashing lines wait until they dissapear and odometer reading is back 69487 or else then release buttom reset is done.

Jan 13, 2011 | 2002 Toyota Camry

1 Answer

My anti theft alarm goes off and makes it to where I can't start my car how do i bypass this


You can't do it; the Theft System it's integrated to the vehicle control computer ECU/PCM; you need install one INTERFACE to make this work.

Review this Wiring Diagram and this comment: when installing a 791 TRANSPONDER BYPASS System on this vehicle it will be necessary to remove the BOTTOM STEERING COLUMN Cover and IGNITION SWITCH TUMBLER to gan access to the Factory Transponder System around the Ignition Switch. To do so will require that you first look at the bottom of the STEERING COLUMN COVER to identify the screw holes from the IGNITION SWITCH TUMBLER RELEASE PIN HOLE, that is required to remove the Ignition Switch Tumbler, the IGNITION SWITCH RELEASE PIN HOLE is the SMALLEST Hole in the plastic cover in this picture. NOTE *** to remove the IGNITION SWITCH TUMBLER, a TORX #15 Bit on a Screw Driver will work just fine. Incert it up into this hole and press, at the same time, turning the IGNITION SWITCH ON and the Tumbler will pull out at the same time. This Must be done to remove the IGNITION SWITCH TUMBLER so that the BOTTOM Steering Column Cover can be removed to gain access to the TRANSPONDER SYSTEM built around the IGNITION SWITCH.

Also, its possible that you need other details from the Taurus's Owners Manual.

Hope helps.

Jun 01, 2010 | 1996 Ford Taurus

1 Answer

Building a derby car and need to know how to wire starter and ingintion


The ignition switch can be just an SPST toggle switch that connects power from the battery side of the starter solenoid to the battery side of the ignition resistor. The starter switch is just a normally-open single-pole push-button. The starter solenoid usually has two small terminals and two large terminals. Wire one small terminal to the battery side of the solenoid and the other small terminal to the starter switch. The other side of the starter switch goes to a good grounding point. This allows the starter to be operated at any time whether the ignition is on or not. Remove a battery terminal to prevent kids from starting the car or turning the ignition on and running the battery down. Hope this helps!

May 16, 2010 | Ford LTD Cars & Trucks

1 Answer

How do you remove the ignition switch from a 1991 ford ranger? there is no hole to a release keeper button. diagram please


u must remove the sterering wheel and then the ignition key cylinder lock pin to pull the switch out

Mar 29, 2010 | 1991 Ford Ranger Supercab

2 Answers

Ignition switch 1992 Lebaron


Hello! Disconnect +battery cable...Remove tilt lever...Remove 3 Torx column cover attaching screws...Then the upper and lower column column covers...Using a Torx with a security tip (also called tamper proof tip) #440-tx20H... Remove 3 ignition switch mounting screws...Carefully pull switch away from column...Release 2 connector locks on 7 terminal wiring connector...Then disconnect from ignition switch...Release connection lock on 4 terminal connector...Then disconnect from ignition switch.

Guru..................saailer

Jan 12, 2010 | 1992 Chrysler Lebaron

1 Answer

2005 chevy cobalt key stuck in ingintion, can not get the key out car will not start seems like battery is dead


Place the transmission shifter in neutral and try starting the car. If the car starts that's a good thing. The bad thing, there is a lock pin in the shifter that activates the micro switch to release the ignition key when it's turned to the off position. It's a simple fix, take the center console a part so you can get to the pin to realign it to the micro switch. When you have it apart you'll see what i mean. Once you have it aligned, the key's will release from the ignition switch. Good luck and hope this helps, and take note: make sure you have a set of tools to take the console a part if this happens again when your out of town.

Jun 05, 2009 | 2005 Chevrolet Cobalt

3 Answers

I have a 2006 colbalt and i can't get the key out of the ingintion


THE MOST COMMON PROBLEM IS IN THE SHIFTER ASSEMBLY. IT HAS A PLASTIC PART IN THE SHIFT LEVER THAT BREAKS NOT ALLOWING THE BTSI SOLENOID TO WORK PROPERLY THUS NOT ALLOWING THE IGNITION CYLINDER TO ROTATE TO RELEASE THE KEY.

Apr 27, 2009 | 2007 Chevrolet Cobalt Coupe

1 Answer

Bonneville ignition cylinder replacement


get new cylinder look at it and see the spring loaded tab you need to push in. Now pull the steering wheel column lock plate (gm tool required unless you have super thumbs) pull out key buzzer switch , roll key over to unlock wheel, press the same area on the lock cylinder to release it

Sep 13, 2008 | 1995 Pontiac Bonneville

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

261 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...