Question about 1992 Chevrolet Lumina

1 Answer

Fluid leaking from intake bypass connection need exploded view of the intake manifold the plastic connector from water by pass is broken i dont know what it is called to re order

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 186 Answers

You may be talking about the heater pipe quick connector located on the lower intake mainfold.Very common to break off on early 3.1 liter engines.Also very difficult to get out with intake on car.most of the time they have to be cut out in pieces with intake removed from engine.hope this helps

Posted on May 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to see a coolant system hose that leaks does the intake have to be removed


Yes there are cooling system hoses under the intake, here are instructions to remove the intake.

Instructions
  1. Remove the Intake Manifold
    • 1Drain the cooling system and relieve the pressure in the fuel system. Disconnect the negative battery cable, the air intake duct, the IAC valve connectors, the throttle position sensor and switch connectors, and the EGR solenoid valve.
    • 2Pull the EVAP canister vacuum and purge hoses, the vacuum hoses from the EVAP, the brake cylinder, pressure regulator and EGR tube. Tag and disconnect the spark plug wires. Remove the distributor cap.
    • 3. Take out the three left bank injector connectors, the thermal transmitter, the ground harness, breather pipe and the upper manifold. Disconnect the fuel feed and return lines and plug them with golf tees to prevent fuel spillage.
    • 4Locate the right injector harness connectors and disconnect them as well as the fuel rail and injectors. Remove the coolant temperature switch harness connector and the water hose from the thermostat.
    • 5Loose the bolts on the lower manifold in sequence. Remove the bolts and left the intake manifold from the engine. Remove the gasket and discard it.
    • 6Clean the mating surfaces by scraping the old gasket material and carbon deposits. Clean the surfaces with solvent and inspect them for damage.
    Install the Intake Manifold
    • 7Put a new gasket in place and install the lower intake manifold to the engine. Tighten the bolts in sequence as follows: first pass-35 inch pounds; second pass-78 inch pounds and third pass 70 to 84 inch pounds.
    • 8Connect the ECT sensor connector, the fuel supply manifold and the right bank injector connectors. Connect the fuel lines and then install the upper intake manifold. Put the breather pipe in position.
    • 9Install the intake manifold ground cable, the thermal transmitter, the left bank injector connectors and the distributor. Reconnect the spark plug wires.
    • 10Continue reconnecting all the components, reversing the order in which they were removed. Connect the negative battery cable to the terminal. Refill the cooling system with the appropriate coolant.
    • 11Start the engine. Check for fuel or vacuum leaks.

Jul 02, 2012 | 1997 Mercury Villager

1 Answer

I need written instructions for installing an EGR Valve on a 96 Ford Exploer Eddie Bauer V6 4.0 engine. Trying to pass emission inspection.


zjlimited_986.jpg

Fig. 4: Exploded view of the EGR system and related components for the 4.0L engine (click over pic for zoom)

REMOVAL & INSTALLATION

PFE/DPFE Sensor
This component is found on all engines, and is also referred to as the backpressure transducer.
  1. Disconnect the negative battery cable.
  2. Detach and label the wiring harness connector from the PFE/DPFE sensor.
  3. Disconnect all of the hoses from the sensor.
  4. Remove the mounting nuts, then separate the sensor from the mounting bracket.
  5. If necessary, remove the EVR solenoid and the PFE/DPFE mounting bracket from the upper intake manifold.
To install:
  1. If removed, install the EVR solenoid and mounting bracket onto the upper intake manifold.
  2. If applicable, install the EGR tube heat shield.
  3. Position the PFE/DPFE sensor on the mounting bracket, then install and tighten the mounting nuts until snug.
  4. Attach all necessary hoses and wiring to the sensor.
  5. Connect the negative battery cable.

EGR Vacuum Regulator (EVR) Solenoid
The EVR solenoid is mounted either on the same bracket as the PFE/DPFE sensor, attached to the upper intake manifold, or near the EGR valve on its own bracket.
  1. Disconnect the negative battery cable.
  2. Label and detach the wiring harness connector from the EVR solenoid.
  3. Detach the main emission vacuum control connector from the solenoid.
  4. Remove the retaining nuts, then separate the solenoid from the mounting bracket.
To install:
  1. Position the solenoid on its mounting bracket and install the retaining nuts.
  2. Attach the main emission vacuum control connector and the wiring harness connector to the EVR solenoid.
  3. Connect the negative battery cable.

EGR Valve
See Figures 6 and 7
  1. Disconnect the negative battery cable.
  2. If necessary, remove the air inlet tube from the throttle body and air cleaner housing.
  3. Label and detach all vacuum hoses from the EGR valve.
  4. Label and detach any electrical wiring harness connectors from the EGR valve.
  5. Disconnect the EGR valve-to-exhaust manifold tube from the EGR valve.
  6. Remove the EGR valve mounting fasteners, then separate the valve from the upper intake manifold.
  7. Remove and discard the old EGR valve gasket, and clean the gasket mating surfaces on the valve and the intake manifold.
zjlimited_987.jpg

Fig. 6: Cutaway view of a base entry type EGR valve

zjlimited_988.jpg

Fig. 7: Cutaway view of a side entry type EGR valve

To install:

  1. Install the EGR valve, along with a new gasket, on the upper intake manifold, then install and tighten the mounting bolts to 4-22 ft. lbs. (20-30 Nm) on 3.8L engines, or to 106-49 inch lbs. (1-18 Nm) on 5.0L engines.
  2. Connect the EGR valve-to-exhaust manifold tube to the valve, then tighten the tube nut to 30 ft. lbs. (41 Nm).
  3. Connect all wiring or hoses to the EGR valve.
  4. Install the air inlet tube.
  5. Connect the negative battery cable.


Hope this helps, good luck (remember to rate this comments).

Apr 06, 2011 | Ford Explorer Cars & Trucks

1 Answer

Where is the starter located on a 2001 toyota tundra


Starter Motor REMOVAL & INSTALLATION 3.4L Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Starter electrical connectors
    • Starter
    To install:
  3. Install or connect the following:
    • Starter. Tighten the fasteners to 29 ft. lbs. (39 Nm).
    • Electrical connections
    • Negative battery cable Fig. 1: Exploded view of a common starter - 3.4L engine 86822088.gif
4.7L Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain the cooling system.
  3. Relieve the fuel system pressure.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Engine appearance cover
    • Air intake tube
    • Intake manifold
    • Starter motor mounting bolts
    • Starter wiring connectors
    • Starter motor
    To install:
  5. Install or connect the following:
    • Starter motor
    • Starter wiring connectors. Tighten the cable nut to 86 inch lbs. (10 Nm).
    • Starter motor mounting bolts. Tighten the bolts to 29 ft. lbs. (39 Nm).
    • Intake manifold
    • Air intake tube
    • Engine appearance cover
    • Negative battery cable
  6. Fill the cooling system.
  7. Start the engine and check for leaks.
prev.gif next.gif

Sep 18, 2010 | 2001 Toyota Tundra

2 Answers

Need to replace the intake manifold


3.8L Engine (most common) Upper Intake Manifold To Remove:
  1. Drain the cooling system.
  2. Remove or disconnect the following:
    • Negative battery cable.
    • Fuel injector sight shield.
    • Air cleaner intake duct.
    • Right spark plug wires from the ignition control module and reposition.
  3. Relieve the fuel pressure.
  4. Remove or disconnect the following:
    • Fuel rail assembly.
    • Brake booster hose from the vacuum source manifold in the upper intake manifold.
    • Exhaust Gas Recirculation Valve (EGR) wiring harness heat shield nut, bolt and the EGR heat shield.
    • Throttle body support bracket upper bolt.
  5. Disconnect the electrical connectors from the following:
    • EVAP purge solenoid
    • Throttle Position (T/P) sensor
    • Idle Air Control (IAC) valve
    • Manifold Absolute Pressure (MAP) sensor
    • Mass Air Flow (MAF) sensor
    • EVAP purge solenoid vacuum line from the throttle body.
    • Accelerator and the cruise control cables with the bracket from the throttle body.
  6. Remove or disconnect the following:
    • Upper intake manifold bolts and stud.
    • Clean the upper intake manifold bolt threads.
  7. Remove or disconnect the following:
    • Upper intake manifold by lifting the back of the intake and sliding the manifold forward from the throttle body support bracket.
    • Upper-to-lower intake manifold carrier gasket from the upper intake manifold.
  8. If the upper intake manifold is being replaced, remove the following:
    • Throttle body assembly.
    • Manifold Absolute Pressure (MAP) sensor.
    • Positive Crankcase Ventilation (PCV) valve.
    • Vacuum source manifold.
Upper intake manifold bolt torque sequence (3.8L engine) gm-03-38-530.gif

To Install:
  1. If the manifold was replaced, install or connect the following:
    • Vacuum source manifold.
    • Positive Crankcase Ventilation (PCV) valve.
    • Manifold Absolute Pressure (MAP) sensor.
    • Throttle body assembly.
    • Upper-to-lower intake manifold carrier gasket to the upper intake manifold.
  2. Carefully place the upper intake manifold onto the lower intake manifold. Ensure that the alignment pins in the upper intake manifold align with the holes in the lower intake manifold. NOTE: Apply thread lock compound, to the bolt threads before assembly.
  3. Install or connect the following:
    • Upper intake manifold. Tighten the upper intake manifold bolts in sequence to 89 in lbs (10 Nm)
    • Accelerator and the cruise control cables with the bracket to the throttle body.
    • EVAP purge solenoid vacuum line to the throttle body.
  4. Connect the electrical connectors to the following:
    • Mass Air Flow (MAF) sensor
    • Manifold Absolute Pressure (MAP) sensor
    • Idle Air Control (IAC) valve
    • Throttle Position (T/P) sensor
    • EVAP purge solenoid
  5. Install or connect the following:
    • Throttle body upper support bracket bolt. Tighten the bolt to 89 in lbs (10 Nm)
    • EGR valve wiring harness heat shield, nut and the bolt. Tighten the nut and the bolt to 89 in lbs (10 Nm)
    • Brake booster hose to the vacuum source manifold.
    • Fuel rail assembly.
    • Right spark plug wires.
    • Air cleaner intake duct.
    • Fuel injector sight shield.
  6. Connect the negative battery cable.
  7. Fill the cooling system.
  8. Inspect for fluid or vacuum leaks.
Lower Intake Manifold (W/O Supercharger) To Remove:
  1. Remove or disconnect the following:
    • Upper intake manifold.
    • Generator brace.
    • Drive belt tensioner with the mounting bracket and the heater water bypass inlet pipe.
    • Exhaust gas recirculation EGR outlet pipe bolt from the lower intake manifold.
    • Radiator inlet hose from the water outlet housing.
    • ECT sensor electrical connector.
    • Right upper engine mount strut bracket.
    • Generator brace bracket bolts.
    • Generator brace bracket.
    • Lower intake manifold bolts.
    • Lower intake manifold.
    • Lower intake manifold seals.
    • Lower intake manifold gaskets.
  2. If replacing the lower intake manifold, Remove or disconnect:
    • Water outlet housing bolt and stud
    • Water outlet housing
    • Gasket and the thermostat.
    • ECT sensor.
  3. Inspect the flatness of inlet flanges.
  4. Clean the intake manifold mating surfaces.
  5. Clean the intake manifold bolts and bolt holes of adhesive compound.
To Install:
  1. If removed, install the ECT sensor.
    • Tighten the ECT sensor to 18 ft. lbs. (25 Nm)
  2. If removed, install the thermostat, the gasket, and the water outlet housing.
  3. If removed, install the water outlet housing bolt and the stud.
    • Tighten the bolt and stud to 20 ft. lbs. (27 Nm)
  4. Install or connect the following:
    • Lower intake manifold gaskets. NOTE: Apply sealer GM P/N 12346286 (Canadian P/N 10953472) or equivalent to the ends of the intake manifold seals.
    • Lower intake manifold seals.
    • Lower intake manifold.
    • Lower intake manifold bolts.
    NOTE: Apply thread lock compound GM P/N 12345382 (Canadian P/N 10953489) or equivalent to the two hidden bolts and ensure they are installed.
  5. Tighten the lower intake manifold bolts in sequence to 11 ft. lbs. (15 Nm) gmpc_v6_5.gif

  6. Install or connect the following:
    • Generator brace bracket.
    • Generator brace bracket bolts. Tighten the bolts to 37 ft. lbs. (50 Nm)
    • Right upper engine mount strut bracket.
    • ECT sensor electrical connector.
    • Radiator inlet hose to the water outlet housing.
    • EGR outlet pipe to the lower intake manifold.
    • EGR outlet pipe bolt to the lower intake manifold. Tighten the bolt to 21 ft. lbs. (29 Nm)
    • Drive belt tensioner.
    • Generator brace.
    • Upper intake manifold.
  7. Inspect for leaks.
Lower Intake Manifold (W/ Supercharger) To Remove:
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the supercharger.
  4. Remove the thermostat housing.
  5. Remove the EGR pipe at the intake manifold.
  6. Disconnect the electrical connection at the temperature sensor.
  7. Remove the intake manifold and gaskets.
NOTE: The coolant bypass tube will release from the intake manifold when the manifold is removed.
To Install:
  1. Clean the gasket sealing surfaces.
  2. Install the intake manifold gaskets.
  3. Align the coolant bypass tube with the opening in the intake manifold and install the manifold. Tighten the bolts to 11 lb ft (15 Nm).
  4. Install the electrical connector to the temperature sensor.
  5. Install the EGR pipe to the intake manifold.
  6. Install the thermostat housing.
  7. Install the supercharger.
  8. Fill the cooling system.
  9. Connect the negative battery cable.

Aug 05, 2010 | 1997 Pontiac Grand Prix

2 Answers

Cylinderhead torque stc.


Cylinder Head Removal & Installation SOHC To Remove:
  1. Relieve fuel system pressure.
  2. Remove timing belt cover. Camshaft timing marks kia-03-20-7032.gif

  3. Turn crankshaft until timing mark on front housing and the arrow "2" on the camshaft pulley align.
  4. Loosen lock bolt on tensioner.
  5. Pry tensioner away from timing belt and tighten lock bolt to relieve tension on the timing belt.
  6. Remove timing belt from camshaft pulley.
  7. Disconnect battery negative cable.
  8. Remove 3 bolts that secure accelerator cable and air intake hose to cylinder head cover.
  9. Detach accelerator cable and place off to side.
  10. Remove the following;
    • Air hose
    • Air ISC air hose
    • Breather hose
    • Vacuum hose from air intake hose
  11. Disconnect mass air flow sensor electrical connector.
  12. Remove air intake hose.
  13. Remove PCV valve from cylinder head cover.
  14. Remove ISC air hose from idle speed actuator.
  15. Remove air hose from behind intake manifold.
  16. Remove 2 screws from high tension wire protectors.
  17. Detach wire loom from holder at rear of cylinder head cover.
  18. Detach vacuum tube at rear of cylinder head cover.
  19. Remove vacuum pipe. Cylinder Head Cover kia-03-20-7042.gif

  20. Remove 7 cylinder head cover bolts.
  21. Remove cylinder head cover and gasket.
  22. Disconnect 2 ignition coil electrical connectors.
  23. Disconnect 2 fuel injection electrical connectors at rear of cylinder head.
  24. Disconnect the following electrical connectors;
    • Oxygen sensor
    • Throttle position sensor
    • Idle speed actuator
    • Oil pressure switch
    • EGR vacuum solenoid valve at intake manifold
  25. Disconnect heater hose from elbow.
  26. Disconnect brake booster vacuum hose and cruise control vacuum hose from surge tank.
  27. Detach wire harness from rear of cylinder head.
  28. Disconnect purge control solenoid vacuum hose from intake manifold.
  29. Disconnect fuel hose from fuel connector assembly.
  30. Remove grounding bracket.
  31. Remove 4 bolts and intake manifold bracket.
  32. Remove starter.
  33. Detach water bypass hose from bypass pipe.
  34. Disconnect water hoses from oil cooler.
  35. Disconnect fuel hose from fuel pipe.
  36. Remove exhaust manifold heat shield.
  37. Remove exhaust flange nuts and front exhaust bracket bolt.
  38. Lower exhaust system. Cylinder head bolt loosening sequence kia-03-20-7050.gif

  39. Loosen cylinder head bolts in 3 steps in proper sequence.
  40. Remove cylinder head bolts and washers.
  41. Remove cylinder head, intake manifold and exhaust manifold as an assembly.
To Install:
  1. Install NEW cylinder head gasket.
  2. Install cylinder head, intake manifold and exhaust manifold as an assembly.
  3. Tighten cylinder head bolts in 3 steps in reverse sequence that was used during removal. Tighten bolts to 62 ft lb (84 Nm).
  4. Install front exhaust bracket bolt. Tighten bolt to 20 ft lb (27 Nm).
  5. Install NEW lower exhaust flange gasket and 3 nuts. Tighten nuts to 24 ft lb (31 Nm).
  6. Install exhaust manifold heat shield. Tighten nuts to 35 in lb (4 Nm).
  7. Connect fuel hose to pipe.
  8. Connect 2 hoses to oil cooler.
  9. Attach water bypass hose to bypass pipe.
  10. Install starter and bolts. Tighten bolts to 34 ft lb (46 Nm).
  11. Install intake manifolds bracket and 4 bolts. Tighten bolts to 32 ft lb (45 Nm).
  12. Install grounding bracket.
  13. Connect fuel hose to fuel connector assembly.
  14. Connect the following electrical connectors;
    • Oxygen sensor
    • Throttle position sensor
    • Idle speed actuator
    • Oil pressure switch
    • EGR vacuum solenoid valve at intake manifold
  15. Connect purge control solenoid vacuum hose to intake manifold.
  16. Attach wire harness from rear of cylinder head.
  17. Connect brake booster vacuum hose and cruise control vacuum hose to surge tank.
  18. Connect heater hose to elbow.
  19. Connect 2 fuel injection electrical connectors at rear of cylinder head.
  20. Connect 2 ignition coil electrical connectors.
  21. Install cylinder head cover.
  22. Install 7 cylinder head cover bolts. Tighten bolts to 60 in lb (7 Nm).
  23. Install vacuum pipe and 2 bolts at rear of cylinder head cover. Tighten bolts to 60 in lb (7 Nm).
  24. Connect vacuum tube to pipe.
  25. Connect loom holder to rear of cylinder head cover.
  26. Install 2 screws to high tension wire protectors.
  27. Install air hose to behind intake manifold.
  28. Install ISC air hose to idle speed actuator.
  29. Install PCV valve to cylinder head cover.
  30. Install air intake hose.
  31. Connect mass air flow sensor electrical connector.
  32. Install the following;
    • Air hose
    • Air ISC air hose
    • Breather hose
    • Vacuum hose from air intake hose
  33. Attach accelerator cable.
  34. Install 3 bolts that secure accelerator cable and air intake hose to cylinder head cover. Timing belt pulley timing marks kia-03-20-7035.gif

    NOTE: Timing belt pulley timing mark and timing mark must be aligned.
    Camshaft timing marks kia-03-20-7032.gif

    NOTE: The arrow at "2" on camshaft pulley must be aligned with timing mark on front housing.
  35. Install timing belt.
  36. Install timing belt cover.
  37. Pressurize fuel system.
  38. Start engine and check ignition timing.

Jul 11, 2010 | 1999 Kia Sportage

1 Answer

Need to replace intake manifold how do you do this


Bonneville, LeSabre, Park Avenue 2000-2005 Intake Manifold - Removal & Installation

3.8L Engine
VIN 1 Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Relieve the fuel system pressure.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    Negative battery cable Supercharger Thermostat housing Exhaust Gas Recirculation (EGR) tube at the intake manifold Engine Control Temperature (ECT) sensor Intake manifold
To install:
  1. Install or connect the following:
    Intake manifold with new gaskets. Torque the bolts, working from the center out, to 11 ft. lbs. (15 Nm). ECT sensor connector EGR tube to the intake manifold Thermostat housing Supercharger Negative battery cable
  2. Refill and bleed the cooling system.
  3. Run the engine and check for leaks and proper engine operation.

VIN K Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect the negative battery cable.
  3. Drain the cooling system.
  4. Relieve the fuel system pressure.
  5. Remove or disconnect the following:
    Fuel injector sight shield Air inlet duct Spark plug wires from the right side Manifold Absolute Pressure (MAP) sensor Vacuum lines from the intake manifold Fuel lines Fuel injector electrical connectors Fuel regulator vacuum line Fuel rail from the intake manifold Exhaust Gas Recirculation (EGR) heat shield Throttle cable bracket from the cylinder head mounting bracket and the throttle body cables Throttle body support bracket Upper intake plenum and gasket Thermostat housing Electrical connector from the Engine Coolant Temperature (ECT) sensor Drive belt tensioner assembly EGR valve outlet pipe Lower intake manifold

    a5adffa.jpg
    Fig. Exploded view of the intake manifold and related components-3.8L (VIN K) engine
To install:


140d431.jpg
Fig. Upper intake manifold torque sequence-3.8L (VIN K) engine


4950e4f.jpg
Fig. Lower intake manifold torque sequence-3.8L (VIN K) engine
  1. Install or connect the following:
    Intake manifold using new manifold gaskets. Torque the bolts in sequence to 11 ft. lbs. (15 Nm); then, re-torque to 11 ft. lbs. (15 Nm). EGR valve outlet pipe Drive belt tensioner assembly. Torque the tensioner bolts to 37 ft. lbs. (50 Nm). Electrical connector to the ECT sensor Thermostat housing Upper intake plenum. Torque the intake plenum bolts to 88 inch. lbs. (10 Nm). Throttle body support bracket Throttle cable bracket to the cylinder head mounting bracket and the cables to the throttle body lever EGR heat shield Fuel rail. Torque the fuel rail bolts to 88 inch. lbs. (10 Nm). Fuel lines Fuel regulator vacuum line Fuel injector electrical connectors Vacuum lines to the intake manifold MAP sensor Spark plug wires Fuel injector sight shield and air inlet duct Negative battery cable
  2. Refill and bleed the cooling system.
  3. Run the engine and check for leaks and proper engine operation.

Hope this help (remember rated this).

May 17, 2010 | 2001 Pontiac Bonneville

2 Answers

I have a 98 lincoln town car executive and I need to know how you change the thermostat


1. drain coolant
2. remove engine cover
3. remove the 2 bolts from water hose connection (upper rad hose connecting to)
4. remove o-ring and thermostat
5. repeat in reverse order

Feb 05, 2010 | 1998 Lincoln Continental

2 Answers

Water leak under the intake manifold,1995 toyota 4 runner


There is a heater core bypass pipe that runs from the block (under the manifold) to the bacl of theengine where you will see a flat rectangular "sheet metal" thing with a pipe coming out of it. The a rubber hose connects. You need to pull the top air plenums and intake to get to it. The p[ipe flange bolts to the block with silicone rtv as a sealant.

Nov 12, 2009 | 1995 Toyota 4Runner

2 Answers

I am trying to locate the starter of my 1998 LS 400 pls. help me.


The starter is located under the intake manifold on this engine.

20d8b81.gif

Jun 17, 2009 | 1998 Lexus Gs 400

1 Answer

Hose from water pump to intake manifold above and behind water pu


this is a water pump bypass hose connector to the manifold, take the broken piece to a parts store and show it to them, it should have the threads still broken off in the manifold so explain that. To remove the broken piece ask for a EZ OUT to fit the piece you took to the store.
It is common for these to become brittle and break off but it is a simple fix.

Feb 17, 2009 | 1993 Buick LeSabre

Not finding what you are looking for?
1992 Chevrolet Lumina Logo

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...