Question about 2004 Jeep Liberty

1 Answer

REPLACE TAIL LAMP BULB

Can you please help me and explane how to replace rt tail lamp bulb on a 2004 jeep liberty. Thank you so much for your help.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Jeep Master
  • 76,846 Answers

By opening the tailgate, you will see two star headed screws. you may need an extension and good lights to get to them. Carefully looses each one with firm pressure using the old standard, (righty tighty, left lucy). Again, be careful not to strip these screws because the can be hard to find.
Next, use a medium sized screwdriver and apply steady pressure between the body and the light case. (MY HUSBAND JUST PULLED THE LIGHT CASE OFF WITHOUT HAVING TO USE A SCREWDRIVER) There are two pins that hold the brake light in place and they need to pulled back carefully so as not to scratch the paint. The brake light is the compartment on the bottom (ACTUALLY IN MY JEEP IT WAS THE TOP CASE) , twist and pull. The unit will come out and then the bulb can be replaced. It should pop into place. Everything else will work in reverse when it comes to assembling the whole unit

Posted on May 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change license plate bulbs in 2004 buick lesabre custom


  1. Disconnect the tail/back up lamp harness connector from the from the body wiring harness.
  2. Remove the tail/back up lamp assembly from the rear compartment lid.
  3. While supporting the tail/back up lamp assembly, unplug the tail/back up lamp harness grommet from the rear compartment lid and remove the tail/back up lamp from the vehicle.
  4. Remove the license plate lamp bulb from the lamp housing.

Sep 22, 2014 | 2004 Buick LeSabre

1 Answer

Replace tail light 2005 jeep liberty


REPLACING THE BULB IS EASY. OPEN THE LIFT GATE, LOOK TO THE SIDE THAT YOU ARE REPLACING. RIGHT BESIDE THE TAIL LIGHT THE ARE TWO SCREWS. REMOVE THEM AND TAIL LIGHT SHOULD JUST PULL OUT. MAKE SURE TO UNPLUG IT AFTER IT IS LOOSE TO MAKE IT EASIER TO REPLACE THE BULB.

Feb 26, 2010 | 2005 Jeep Liberty

1 Answer

How do I remove and replace tail light assembly to replace the bulb?


you will need to remove the 1/4 panels plastic trim inside your Jeep to get to the inner nuts to the tail lamp.

Jan 16, 2010 | 2004 Jeep Grand Cherokee

1 Answer

How do you replace the tail light bulbs on a 2006 Pontiac Vibe


Tail Lamp: Service and Repair
TAIL LAMP REPLACEMENT
REMOVAL PROCEDURE
1. Open the rear compartment lid.
2. Remove the rear compartment trim panel (4).
3. Disconnect the tail lamp electrical connectors.
4. Remove the following components from the vehicle:
- The 3 nuts (3)
- The tail lamp (7)
5. Remove the following from the tail lamp:
- The stop lamp socket (2)
- The turn signal lamp socket (5)
6. Remove the following from the lamp sockets, if necessary:
- The stop lamp bulb (1)
- The turn signal lamp bulb (6)
INSTALLATION PROCEDURE
1. Install the following to the lamp sockets, if removed:
- The stop lamp bulb (1)
- The turn signal lamp bulb (6)
2. Install the following to the tail lamp:
- The stop lamp socket (2)
- The turn signal lamp socket (5)
3. Install the tail lamp (7) to the vehicle. Secure the tail lamp (7) with the 3 nuts (3).
NOTE: Refer to Fastener Notice in Service Precautions.
Tighten the tail lamp nuts to 10 N.m (89 lb in).
4. Connect the tail lamp electrical connectors.
5. Install the rear compartment trim panel (4) to the vehicle.
6. Close the rear compartment lid.

Oct 30, 2009 | 2003 Pontiac Vibe

1 Answer

2004 thunderbird tail lamp burned out. How do I


Look in the trunk pull the cover or lining away so you can get at the bolts to remove lamp housing if bulb socket isn't in site

Sep 26, 2009 | 2004 Ford Thunderbird

2 Answers

Computer flashes tail lamp failure and my tail lights and liciense plate light all work. what is the problem?


Hello and welcome to Fixya.com.
Check to see if you have twin tail lamp bulbs on rear i mean when i say this two tail lamp bulbs fitted to each side,check to see if one of the bulbs has blown if so replace it this will correct your computor.
Best regards.
George...

Jul 23, 2009 | 1996 Jeep Grand Cherokee

1 Answer

NEED TO REPLACE A TAIL LIGHT BULB IN A 2005 CHEVROLET IMPALA


and Repair Notes TAIL LAMP REPLACEMENT REMOVAL PROCEDURE Open the rear compartment. Remove wingnut and pull back the rear compartment trim panel from the tail lamp. Remove the wingnuts from the tail lamp. Remove the tail lamp from the rear body panel. Disconnect the electrical connector from the tail lamp. Remove the tail lamp socket, turning counterclockwise. Remove the bulb from the tail lamp socket. Remove the sidemarker lamp socket, turning counterclockwise. Remove the bulb from the sidemarker lamp socket. INSTALLATION PROCEDURE Install the bulb to the tail lamp socket. Install the bulb to the sidemarker lamp socket. Install the sidemarker lamp socket, turning clockwise. Install the tail lamp socket, turning clockwise. Connect the electrical connector to the tail lamp. Install the tail lamp to the rear body panel. Install the wingnuts to the tail lamp. Pull back the rear compartment trim panel to the tail lamp and install the wingnut. Close the rear compartment.

Jun 08, 2009 | 2005 Chevrolet Impala

1 Answer

Break kight burned out


Open the liftgat and you should see the screws on the side of the lamp. Unscrew then and pull the lamp away from the vehicle. There should be sockets in the tailamp that screw in and out about the size on a half dollar. Pull this out and pull the bulb out straight and replace by pushing in a new bulb. Follow these directions backwards to replace the lamp. Hope this helps.

Jan 12, 2009 | 2006 Jeep Commander

1 Answer

Hyandia Accent


not sure which top tail light you mean? do you wish to replace bulb or actual lamp on the rear screen? this is the high level brake light ! OR do you wish to replace bulb in one of the rear tail lamps offside/nearside ? which ever ? the h/level brake light bulb is accessable for bulb from the rear panel on hatch behind lamp bulb is 16 watt capless push in type

Nov 10, 2008 | 2003 Hyundai Accent

1 Answer

Replacing the tail light


Look inside behind the light and see if there is an access cover, if not you will have to remove the tail lamp to replace the bulb. If you open the rear hatch and look at the lamp you should see a couple of screws that hold the lamp to the car. Remove these and pull the light out.

Jul 09, 2008 | 2004 Mitsubishi Endeavor

Not finding what you are looking for?
2004 Jeep Liberty Logo

Related Topics:

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...