Signal light and Windshield-Washer Pump

If the windshield wipers on your 2002 Corvette won't shut off, it could indicate a problem with the wiper control switch or a malfunction in the wiper motor circuit. Here are some troubleshooting steps you can try:

1. Check the wiper control switch: Ensure that the wiper control switch is in the "Off" position. Sometimes, the switch can get stuck or malfunction, causing the wipers to stay on. Try moving the switch back and forth a few times to see if that resolves the issue.
2. Inspect the wiper motor relay: The wiper motor relay controls the power supply to the wiper motor. If the relay gets stuck or fails, it can cause the wipers to stay on. Locate the wiper motor relay in the fuse box or relay panel and try replacing it with a known working relay of the same type to see if that resolves the issue.
3. Check the wiper motor circuit: The wiper motor circuit may have a short or an electrical problem that is keeping the wipers engaged. Inspect the wiring harness connected to the wiper motor for any signs of damage or loose connections. Use a multimeter to check for continuity and proper voltage in the circuit. If you are not familiar with automotive electrical systems, it is advisable to consult a professional technician or a qualified electrician.
4. Disconnect the battery: As a temporary solution, you can disconnect the negative terminal of the car battery to stop the wipers from running. This will disable other electrical components as well, so it's recommended as a temporary measure until the issue can be properly diagnosed and repaired.

Question edited for clarity. Part of duplicate question added.
Duplicate question deleted.
Question moved to model category.

This says Pulse Board or the Switch

https://www.google.com/search?q=2004+Pontiac+Montana+front+wipers+won%27t+turn+off

This says it does have a relay... but

https://www.google.com/search?q=2004+Pontiac+Montana+wiper+relay

Nothing shows where it is located.

https://www.google.com/search?q=2004+Pontiac+Montana+wiper+relay+location

Relay here

https://www.autozone.com/electrical-and-lighting/wiper-motor-relay

It may not be releasing, you can test if you can find it!

https://www.autozone.com/electrical-and-lighting/wiper-motor-relay

..

Replacing parts just to replace them wont fix a bad wire or part. Better to use a voltmeter and ohn meter to check if your getting power to the wires. You may have a bad connection or bad switch on the column for the pumps. Without checking the circuits it will behard to tell what it is thats wrong. Find a wiring diagram and trace the wires and components.

Wiper/Washer System Components
The Wiper/Washer System consists of the following electrical components:
• Accessory relay
• Heated washer nozzles w/XA7
• WASH NOZ 10A fuse
• Windshield washer fluid level switch
• Windshield washer pump motor
• Windshield wiper motor
• Windshield wiper motor module
• Windshield wiper/washer switch
• Wiper/washer switch 10A fuse
• Wiper motor 30A fuse

Wiper/Washer System Operation
The windshield wiper motor module is part of the windshield wiper motor cover and controls wiper motor operation. The accessory voltage supply circuit to the windshield wiper motor assembly is used to operate the wiper motor in all modes. The windshield wiper motor is a 2 speed motor and is operated at low speed in all modes except HIGH. The accessory voltage supply circuit to the windshield wiper/washer switch is used to supply the windshield wiper switch signal circuits. The windshield wiper switch signal circuit voltage levels to the wiper motor module determine the wiper motor operating mode.
When the wiper/washer switch is in the LOW position voltage is supplied through a 24K ohm resistor within the switch to the windshield wiper switch signal 2 circuit, and accessory voltage is supplied to the windshield wiper switch signal 1 circuit. The reduced voltage from the wiper switch signal 2 circuit and accessory voltage from the wiper switch signal 1 circuit causes the wiper motor module to close the wiper motor accessory voltage supply circuit to the wiper motor low speed terminal.

Do you know how to test automotive electrical circuit's using a DVOM - digital volt ohmmeter ? Do you know what a wiring diagram is an how to read one ? Free wiring diagrams here http://www.bbbind.com/free-tsb Enter vehicle info. year , make , model an engine size. Under system click on body & accessories ,then under subsystem click on wiper/ washer's . Click the search button then the blue link.

Windshield Wiper/Washer System Components
The windshield wiper/washer system consists of the following components:
• Windshield wiper/washer switch
• Windshield wiper motor
• Windshield washer pump
• Windshield washer relay
• Outside moisture sensor
• FRT WIPER 25A fuse
• W/S WASH 15A fuse
Windshield Wiper/Washer System Operation
Accessory voltage and ground is supplied to the windshield wiper motor and provides the power for operating the wiper motor and logic power to the wiper motor module. The WASH, MIST, LOW, and DELAY modes are controlled by the windshield wiper/washer switch through a series of internal resistors. The windshield wiper switch supply voltage circuit is a 12-volt reference from the wiper motor module to the wiper/washer switch, and the switch position determines the point on the resistor assembly where the reference voltage is applied. The windshield wiper switch signal 1 circuit supplies the voltage from the resistor assembly to the wiper motor module and the signal voltage determines the operating mode. High speed operation is controlled by the windshield wiper/washer switch through the windshield wiper switch high signal circuit. The windshield wiper switch high signal circuit is supplied 12 volts by the wiper motor module and when the wiper/washer switch is turned to the HIGH position the windshield wiper switch high signal circuit is grounded through the switch ground circuit. The windshield washer pump is controlled through the windshield wash relay. The windshield wash relay coil and switch is supplied battery positive voltage, and during WASH mode the wiper motor module grounds the washer relay control circuit energizing the relay. When the relay is energized battery positive voltage to the switch side of the relay is supplied to the washer pump control circuit.

The is the symptom of a defective wiper switch.

The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper micro relay
• Wiper 2 relay
• Wiper diode
• Windshield wiper motor
• Windshield washer pump
• Windshield washer nozzles
• Windshield washer solvent container
• Windshield wiper arm and blade assemblies
• Windshield wiper transmission
• WIP/WASH 10A fuse
• WIPER 25A fuse

Wiper/Washer System Description
The body control module (BCM) controls wiper motor low speed operation. The washer pump and high speed operation are controlled directly by the wiper/washer switch. The windshield wiper/washer switch supplies voltage on the signal circuits to the BCM for windshield wiper/washer operation. When WASH, MIST, DELAY, LOW, or HIGH is detected, the BCM energizes the wiper micro relay by suppling voltage to the relay coil. This allows battery voltage from the WIPER fuse to flow through the relay switched input then through the contacts and out the relay switched output to the wiper 2 relay switch contacts. Since the wiper 2 relay switch contacts are normally closed to the low speed circuit of the windshield wiper motor, the motor will operate at low speed.

Low Speed Operation
When the wiper switch is in the Low position, voltage is supplied through an internal resistor to the signal circuit. The body control module (BCM) monitors the windshield wiper switch signal 1 circuit, and energizes the wiper micro relay which will operate the windshield wiper motor. The wiper motor will operate at low speed, since the wiper 2 relay is de-energized. Low speed can also be commanded with a scan tool, by commanding Wiper Relay Cmd. ON and OFF. Refer to Scan Tool Output Controls .
High Speed Operation
In the High position, the windshield wiper/washer switch supplies voltage to both the wiper micro relay and wiper 2 relay coils. This energizes both relays and allows battery voltage from the wiper micro relay switched output to the switched input of the wiper 2 relay through its contacts and out the switched output of the wiper 2 relay to the high speed circuit of the windshield wiper motor. The windshield wiper motor will operate at high speed. During high speed wiper motor operation the wiper switch signal circuit is at the low speed signal voltage, and the body control module (BCM) supplies redundant voltage to the wiper relay via the wiper diode.

This info is out of hummer factory service manual !

This is a complex wiper system . Here are all the components involved !
The Wiper/Washer System consists of the following components:
?€¢
Windshield wiper/washer switch

?€¢
Body control module (BCM)

?€¢
Wiper 1 relay

?€¢
Wiper 2 relay

?€¢
Wiper diode

?€¢
Windshield wiper motor

?€¢
Windshield washer pump

?€¢
Windshield washer nozzles

?€¢
Windshield washer solvent container

?€¢
Windshield wiper arm and blade assemblies

?€¢
Windshield wiper transmission

?€¢
WIPER/SW 10A fuse

?€¢
WIPER 25A fuse

Circuit/System Description
The body control module (BCM) controls the wiper motor based on input from the windshield wiper washer switch. The BCM monitors the wiper washer switch through three separate signal circuits and a ground circuit. The windshield wiper switch high signal circuit is used to determine high speed wiper operation, the windshield wiper switch low signal is used to determine low speed, intermittent, and mist operation through the use of a resistor ladder, and windshield washer switch signal circuit is used to determine washer operation. The windshield wiper motor park operation is controlled by the BCM. The BCM recieves an input from the park switch to determine wiper blade position. When the wiper blades are at the bottom of the windshield glass in park position the wiper park switch will open and the circuit will be pulled up to B+ by the BCM. The park signal will be pulled to ground by the wiper motor park switch while the wiper blades are not in the park position.
The BCM controls the windshield wiper motor through two output controls, controlling two relays which determine the desired wiper speed, high or low
Diagnostic Trouble Codes (DTCs)
The body control module (BCM) monitors the voltage on the windshield wiper switch signal 2 circuit for diagnostic purposes. If the circuit is shorted to voltage while the driver is commanded OFF, the BCM will store DTC B3715. If the circuit is shorted to ground while the driver is commanded ON, the BCM will store DTC B3715. Refer to DTC B3715.
It would be best to have a factory scan tool to diagnose this problem . it would make it easier anyway .
It

then one blown out. LOL
09 civic.
it in the glove box, ever read the fuse sections.?
there are 7 civics, which one? hummmmmmmmm
http://justgivemethedamnmanual.com/honda/honda-civic-sedan-owners-manuals/

page 275?
fuse 38 ,washer.... the schematic shows, fuse 10 too.
the FSM covers this best. as always, electrics...
alldata.com, its all there.

Depends on if you want a new windshield or one out of a salvage yard, what quality of tires you want, used or new headlight, and what quality of parts you want to use for the tune up and how complete of a tune up. Also depends on who does the work and where you take it. I would say you are looking at easily a minimum of 700-800 dollars.