Question about 2000 Mazda 626

2 Answers

I have mazda 2 with key fob problem it locks car but will not unlock???i have to use key please help!!!!

Posted by on

  • johnsimonmat May 15, 2009

    no it has a new battery and just has lock/unlock buttons it will lock the car but not unlock

  • John Gwilliam May 11, 2010

    does the key fob have a light in it that tells you its working???

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I had a similar problem with a second-hand Mazda2, was intermittent too so the seller kept telling me it was OK. Eventually turned out to be a loose connection with the fob, I bought another off eBay and billed the garage for it, found instructions for programming it online and it's worked ever since.

Posted on Jul 04, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 74 Answers

Ok so when you press the luck button on the fob does it make a clicking noise? if so does the unlock button sound the same? if pressing the two buttons sounds different then the key-fob switch is faulty. if they sound the same its more than likely the car is at fault if you can open the car manually with a key check all the fuses it could be as simple as that. regards John

Posted on May 15, 2009

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ryan_marcum
  • 3 Answers

SOURCE: can't lock mazda 626. tried fob and manual key. each time it switches to unlock ?

Did you try locking it to see if it could possibly have a reverse effect. Or if theres a short in the wireing harness

Posted on Nov 21, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Our 2001 Mazda MPV doors are not locking. Before, we were able to lock all doors just by locking manually locking from the inside on the driver side and using the remote keyless entry. Now, when we try...


The clicking you hear is the vehicle asking for the program sequence to reprogram the locking system. Apparently something threw it out of sequence, ( a battery change , jumpstart, voltage spike , etc). The programming sequence that mazda uses is really kinda crazy. I was able to locate the sequence to try. If it does not work have the dealership flash the pcm, (another word for reprogram the powertrain control module). Here is the sequence:
1) Get in MPV with ignition key, and all fobs for the vehicle.
2) Close all doors and remove ignition key if it is in ignition.
3) Open driver's door
Note: Steps 4 and 5 must be completed in under thirty seconds.
4) Repeat the following three times
a) Insert ignition key
b)Turn ignition switch to on and then to lock
c) Remove ignition key
5) Repeat the following three times
a) Close driver's door
b) Open driver's door
Locks should all lock and then unlock within a couple of seconds--you'll hear the clicking sound
6) Press any button two times within five seconds on fob being programmed.
Locks should again lock and unlock
7) Repeat step 6 for all other fobs being programmed. When done with last fob, wait a few seconds and then you should be done with the reprogramming. Each fob should now work for this vehicle.

Dec 05, 2014 | 2001 Mazda MPV

1 Answer

Seat Ibiza (2003) Remote central locking failed. Car only lock and unlock with key,it is a second-hand car so I dont have another key to try. Anyone help, Thx


check the battery in the fob, replace it. then get in the car put key in the ignition and turn to number 2 press fob door should lock then press fob again to unlock then take key out and test again should be fine again then.

Mar 19, 2014 | Seat Ibiza Cars & Trucks

1 Answer

2008 chevy equinox power locks not working


1) Your key fob could need a new battery.
2) Your fuses could need checking.

Jun 23, 2012 | 2008 Chevrolet Equinox

1 Answer

How can I reprogram my Jaguar X Type Key so I can unlock and lock my doors?


if your just programming the fob to the module and it has not been replaced and your just needing a manual reset,then follow the folowing procedure:

1 Insert key into ignition
2 Turn key to 'I"
3 Turn key "II" and back to 'I' quickly 4 times
4 Alarm system will chime once when key is back to 'I' for the
fourth time
5 Remove key from ignition
6 Press any button on each key fob and alarm system will chime
for each fob if it has been programmed correctly
7 Press unlock/lock/trunk etc to make sure everything works

Dec 12, 2011 | 2003 Jaguar X-Type

1 Answer

Can't lock mazda 626. tried fob and manual key. each time it switches to unlock ?


Did you try locking it to see if it could possibly have a reverse effect. Or if theres a short in the wireing harness

Nov 21, 2011 | 2000 Mazda 626

1 Answer

Bmw 325 on a y reg will turn over but will not fire fault code pointing immobilizer fault anti tamper fault any ideas easy cheap fix thanks


Hi Mark you could try to see if re-programming the key might do it, you could also disconnect the battery for 10 minutes and see if it resets that way...to re-program the key this is what you do, please follow by the book or it wont work, this however is just a trial to see if it will do the job, if reprogramming the key does not do it, then disconnect the battery for ten minutes and then try re-programming of the key...
1, unlock the car with the key ( not fob) get in and shut the door 2, switch ignition on and then off ( do not try to run it just on then off) 3, remove ignition key 4, press and hold unlock button 5, press lock button 3 times quickly all within ten seconds keeping the unlock button pressed 6, release unlock button 7 ( if you have this type of key fob) the led will flash slowly for 10 seconds 8,( if you have this type of key fob) the central locking system will lock and unlock rapidly to indicate correct programming 9 ( if you have this type of key fob) repeat procedure if the led flashes constantly, or the locking system does not unlock and lock rapidly please follow as directed..if you have any problems understanding what to do, please contact me on email address s.e.morris@live.co.uk hope this helps

Jan 13, 2011 | 2001 BMW 325

1 Answer

Neither key fob for our mazda 6 unlocks the car. A red light flashes on the fob, so I'm not sure it's the battery. Is there some way to reset the system so the fob works?


all you have to do to reset the coding is hold the lock button down for a minute or two till the locks click locked. then test it again by unlocking them. if the button light flashes rapidly then the batt is low, which will affect the distance for use. (do the re-code right next to the vehicle for best results.)

Dec 31, 2010 | Mazda MAZDA6 Cars & Trucks

1 Answer

Key fob will not lock or unlock vehicle. tried 2 different fobs.


unit in the motor playing up,this will be beyond the average DIY owner so its a dealer only job

Oct 30, 2009 | 2004 Mazda 6

4 Answers

Code to program my key fob


Here are the program instructions

1. Close the vehicle doors.
2. Turn OFF the ignition.
3. Remove the key from the ignition.
4. Press and hold the driver side door lock switch in the UNLOCK position.
5. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
6. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
7. Insert the ignition key into the ignition lock cylinder. (Do not turn the ignition key in the lock cylinder.) Leave the ignition key in the ignition lock cylinder.
8. Release the door lock switch. The vehicle will sound three beeps in order to verify the Program Mode has been activated.
9. Press the LOCK and UNLOCK buttons together on the keyless entry transmitter and hold until the vehicle beeps twice to verify that the transmitter has been successfully programmed (this take approximately 15 seconds).
10. Perform the previous step to program up to four transmitters (including your old ones).
11. Remove the ignition key in order to exit the Program Mode

Oct 25, 2008 | 1999 Oldsmobile Intrigue

3 Answers

Mercedes S320 central lock


if you hav a remote control key &yr car wont respond . change key batrrey &contact dealer if still dont work for software

Jul 13, 2008 | 1994 Mercedes-Benz S-Class

Not finding what you are looking for?
2000 Mazda 626 Logo

1,782 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...