Question about 1989 Jeep Cherokee

1 Answer

I'm looking for a way to put water into the radiator that has no cap to open.

I've been looking were to fill the radiator from. There appears to be no cap.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

Closed system? there should be an expansion tank on the fender with a screw on cap....Same rule as a radiator...don't open hot. Fill to the full mark when running.

Posted on May 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I put the water in the radiator?, where is the opening?


Should have a clear plastic tank on one side of the engine compartment with a cap. A hose runs from the top of the radiator to the tank.
The tank for the windshield washer has a snap on cap, the radiator reserve tank has a twist on cap.

Jan 31, 2013 | 1999 Chevrolet Cavalier

1 Answer

My car is leaking a lot of water


leaking onto the ground? or 'Dissapearing'?

If 'Dissapearing' it is probably a blown head gasket.
to check: remove the radiator cap while cold, fill the radiator to the top. start the engine. If bubbles of air come out of the radiator cap, the head gasket is blown.

If leaking on the ground, it is most likley a split hose/radiator/pump.
fill the water up, put the cap on, and let the car idle till warm, have the bonnet open, and look for the escaping coolent.

Sep 30, 2012 | 1995 Oldsmobile Cutlass Ciera

1 Answer

Where do I put water in for radiator ?


When engine is cool, take off radiator cap, and fill radiator. Then fill the coolant recovery container to halfway between the full cold mark and the full hot mark. Start engine (with radiator cap still off) and wait for the thermostat to open (upper radiator hose will get hot). Shut off engine, top up radiator, and put the radiator cap on. Fill the coolant recovery tank to the full hot mark.
You should mix the water and anti-freeze in a 50/50 mix before putting it in the car, you know. Cheers.

May 14, 2012 | 2001 Citroen Xsara Picasso

2 Answers

06 impala bleed air out of cooling system


Put heater on high heat to circulate water in those hoses and heater core. Then start the car after removing the radiator cap and filling with coolant to the top. When the radiator opens you will see the liquid level go down- add more coolant and keep adding till it stays full. Meanwhile fill the overflow to recommended level. When radiator level goes down no more, put radiator cap back on and let engine and coolant cool. If any more water is needed the vacuum created by the shrinking water will draw it in from the overflow.

Jan 11, 2012 | 2006 Chevrolet Impala

2 Answers

1990 subaru legacy- overheats, I"ve


Most likely you put the thesmostat in upsid down. Good luck

Aug 17, 2011 | 1990 Subaru Legacy

2 Answers

What is the correct way to fill the radiator of a chevrolet venture The low coolant light came on then started flashing but the radiator is full of water but has no anti freeze is this the problem


Hi there!
First.- with the engine off and cool, put a flush and drain radiator cleaner run the engine for 10 minutes, turn it off, let it cool down.
Once the engine is not too hot, open the lowest hose of radiator while you put water in the main mouth of radiator.
Once you see the water flushing clear, put the hose back and then fill it with special GM antifreeze, (the one is orange color) put all gallon into it and the rest of water, LOOK FOR THE ONE YOU CAN ADD WATER, THAT'S THE BEST FOR YOUR VAN... Good Luck!

Jun 30, 2011 | 2000 Chevrolet Venture

1 Answer

How to change water pump


remove radiator fanbelt then water pump you will need a diagram for this, the water pump has from 4 bolts or more depending on year. the main thing is to clean!!!!! the surface good. put gasket and rtv on new pump reverse task. remember to replace coolant. run with radiator cap off but don't drive. when the themostat opens fill. turn off put cap on fill resevoir

Aug 15, 2010 | Chevrolet TrailBlazer Cars & Trucks

2 Answers

How do i put water for the radiator?


Does your car have a cap or a sealed unit? You don't want a sealed unit. You want to be able to check your water.Push down and Twist the cap off when cold, not hot, fill it up with coolant, 50/50 mix, and fill up the expansion tank. It says coolant on it. The car will balance itself out. Check the water in your battery while you are at it. It dries out too. Then check the brake fluid, power steering fluid, and oil. That should keep you busy next Saturday. Hope this helps.

May 23, 2010 | 2002 Mercury Cougar

1 Answer

I have a 99 Chrysler 300M that had a slight radiator leak...I had put stop leak in it and it seemed to help for awhile. I know that radiator is aluminum & plastic...well yesterday something happened...


If there is other leak other than the one you have found, air may have entered the system. To ensure that it does not get in and that your are filling up the correct amount of water squeeze the radiator hose on top after each fill to squeeze out the air. You can also let the engine run while pouring water one at a time.

Jun 30, 2009 | 1999 Chrysler 300M

2 Answers

Volvo 1994 Radiator


hi my name is paul
these days most cars have a expansion tank under the bonnet or hood
this is were you fill it up with water it looks like a plastic bowl with a screw lid
DO NOT UNDER ANY CIRCUMSTANCES UNDO CAP WHEN ENGINE IS RUNNING OR IS STILL HOT *** DANGER OF SCALDING DO NOT OVERFILL CHECK OUT MAX LEVEL
car manufacturers use expansion tanks because as the water in your engine warms up it expands under high pressure and fills up the expansion tank with excess water when the engine cools down the water cools and it shrinks and goes back into the cooling system hope this information has been usefull
regard paul

Jul 11, 2008 | 1994 Volvo 940

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7711 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...