Question about 1993 Chevrolet S-10 Blazer

2 Answers

I just put in a rebuilt 1993 s10 motor and cant find the wire to set the timing. been behind glove box and under dash but no wires worked. what else can i do?

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,623 Answers

Ignition timing is electronically controlled on the 4.3 V6.
You will have to disconnect a connector on a little tan and black wire that is against the firewall just above the front passengers feet. (inside vehicle) Then you can time it to specs...
Good luck...i hope this helps.

Posted on May 15, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 335 Answers

To set the timing you will have to find a black connector that is running beside the wiring harness next to or near the distributor. It is a single wire connector and must be disconnected in order to set the timing properly. Hope this helps.

Posted on May 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the security box on 1993 gran cherokee located


Security Alarm Module is located in rigt side box of glove box (attached image) from Repair Manual (Wiring Section).

3_22_2012_12_31_19_pm.jpg

Hope helps.

Mar 22, 2012 | 1993 Jeep Grand Cherokee

1 Answer

I need to know the timing specs for a 1988 Chevy S10 Pickup 2.8


2.8L 10 BTDC .. this is with the 1 connector brown wire.. usually under the glove box, or under the hood behind the distributor.. disconnect that wire to set the timing..

Thanks for the vote.

Dec 22, 2010 | Chevrolet S 10 Cars & Trucks

1 Answer

Location of blower motor on 97 Cherokee classic


the blower motor is on passengers side behind glove box. you can take it out from under glove box dash. to make the job easier, you may have to remove some fuses or relays because the blower motor will not come out with fuse box in the way. remove wiring connector to fan. then take out 3 or 4 screws that hold it in, then wiggle it straight out. if replacing, use old fan cage to put on new fan motor shaft. have a good holiday !

Dec 19, 2010 | 1997 Jeep Cherokee Country

2 Answers

Where is the heater blower motor located?


the fan is located on the pasenger side behind the glove compartment in a black box which is also part of the hvac ducting system. you should see a set of wires going to it. happy holidays

Dec 28, 2009 | 1993 Buick Roadmaster

4 Answers

Need to know where the heater blower motor resistor switch is located in a 1998 GMC sierra V8


Unless they moved it and are still using the same part,I would say that this one is located behind the glove box sandwitched between the underside of the dash and the top of the airbox.The blower motor is mounted to the underside of the airbox.

Oct 17, 2009 | GMC Sierra 1500 Cars & Trucks

2 Answers

How to change front blower motor in a 2003 dodge caravan


Removal & Installation
CAUTION The Supplemental Inflatable Restraint (SIR) system must be disarmed before removing the blower motor assembly. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.

  1. Disconnect and isolate the negative battery cable, then wait 2 minutes before proceeding with the removal. This will effectively disable the air bag system preventing possible personal injury.
  2. Remove the glove box from the instrument panel
d6b70fa.gif
The blower motor is located behind the glovebox, behind the blower motor cover

  1. Remove the A/C-heater blower motor cover.
  2. Disconnect the blower motor wiring connector.
  3. Remove the blower motor wiring grommet and feed the wiring through the blower motor housing.
  4. Remove the blower motor mounting screws.
0e0729c.gif
Once the cover is removed, unplug the electrical connector and push it through the opening in the housing

1ed158c.gif
The blower motor is secured to the housing with three small screws

  1. Allow the blower motor assembly to drop downward to clear the instrument panel and remove from vehicle.
To install:
  1. Place the blower motor assembly into position on the A/C-heater unit and tighten the mounting screws.
  2. Route the blower motor wiring through the blower motor housing and seat the wiring grommet in the hole of the blower motor housing.
  3. Reconnect the blower motor electrical connector.
  4. Install the A/C-heater blower motor cover.
  5. Install the glove box into the instrument panel.
  6. Reconnect the negative battery cable. Check blower motor operation.

Oct 12, 2009 | 2003 Dodge Caravan

2 Answers

Blower motor not working


blower motor is located on the passenger side behind the glove box should be able to access it by removing the lower panel under the dash. fuse will probably be the on for the a/c blower.

Aug 24, 2009 | 1997 Ford Taurus

1 Answer

Finding the blower resistor 2002 Expedition


u must remove the hush panel under the glove box to see the part.

Jul 23, 2009 | 1999 Ford Expedition

5 Answers

Front blower fan not working. checked fuse and relay, not the problem. went out suddenly. what do i check next


the blower motor, is replaceable, and it is cheap, is a diy job, with a 10mm socket go underthe dash no the passenger footwell and behind the glove compartement is the fan blower replace with a new unit.

Jul 14, 2009 | 2001 Dodge Caravan

1 Answer

No power to injectors


are they plugged in?
check the fuse

Dec 13, 2008 | 1992 Chevrolet S-10

Not finding what you are looking for?
1993 Chevrolet S-10 Blazer Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...