Question about 2007 Hummer H3X

1 Answer

How do you remove the front tow hook brackets on a 07 hummer h3

I removed the 2 bolts but something is still holding it .

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

Put the bolts back in and tap them with a hammer it will push the bracket out and then take the bolts out 

Posted on May 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

There's an annoying creaking sound coming from around my right rear wheel on my 2005 Accord. I think I've identified it as the trailer arm. Is that something I can replace myself?


they are usually fairly easy to replace, remove the large bolt that holds the arm to the knuckle, then remove the 2 bolts that hold the arm to the sub frame. Just grunt work really, not too hard.

May 23, 2011 | 2005 Honda Accord

1 Answer

I dont know how to remove my battery something s holding it down but i see no bolt. 2000 lincoln continental


On one of the side is a hold down its in either side if your battery youll need a extension , with a 13mm or 1/2, or its a 15mm nut with a hold down plate, just unscrew, and remove plate its about 3 inches long and 2 inches wide and out the battery comes

May 03, 2011 | 2000 Lincoln Continental

1 Answer

I need to replace a 2001 hyundai tiburon starter


Hi, Disconnect car battery.
Remove cover from air intake. Remove Filter.
Remove Filter intake housing (3 inner bolts) and large hose at the furthest screw collar. (This is important as you will need to reach the bolts to the starter by reaching from the top down via that location)
Remove the starter/ acceleration cable (1 bolt at the end of the cable, 2 bolts at the guide point screwed intot the engine block)
THE STARTER IS LOCTED AT THE BACK OF THE ENGINE WITH ONLY 2 BOLTS HOLDING IT IN PLACE
Remove the 2 bolts about half way with a socket wrench, remove the bolt sthe remining way with hand or open end wrench. (This is necessary especially on the lower bolt as there is liited work space.)
Take hold of the the starter using a partially blind reach and patially pull it out slightly turning it around so you can see the connectors.
Remove connectors........ Remove clip, the the bolt that holds the positive cable.
You can now fully remove the starter.
Take it 2 the local auto parts to have it tested. Have them test it 4 to 5 "bumps" as when mine was initially tested it worked fine but after 2 to 3 more attempts it froze and would operate.
To reinstall reverse procedure
Take care

Jul 30, 2010 | Hyundai Tiburon Cars & Trucks

1 Answer

How to install front brake rotors for 2004 odyssy?


1. remove 2 bolts holding caliper on (either 12 or 14 mm)
2 remove 2 bolts holding caliper bracket (which holds the brake pads) (17mm)
3. remove the 2 phillips head bolt holding the rotor on
4 remove rotor, if rusted may need to tap it off
5 reverse procedure, when reinstalling caliper, may need to press piston back into caliper to get it to fit over new rotor

Feb 20, 2010 | 2004 Honda Odyssey

2 Answers

How many bolts to remove starter on 2003 x type?


Standard configuration would be two mechanical bolts holding the starter on and a nut holding on the wire. What size? I dunno - 7/16 - 1/2 - 9/16 - 5/8 - 11 mm - 12 mm - 13 mm - 14 - mm something close to those.

Jan 17, 2010 | 2003 Jaguar X-Type

1 Answer

How to remove altenator for 1999 Plymouth Grand Voyager 3.3 litre


Before the step-by-step instructions I want to make sure this is the Alternator that needs to be replaced and not something else. This will save you money for an Alternator you don't need and save you time for replacing a good alternator.
Start the vehicle. With the engine running - disconnect the Negative Cable from the Battery. If the Engine dies - it is the Alternator. If it doesn't die - it is not the Alternator. I have had plenty of people who have replaced perfectly good Alternators only to find out it was something else.
Step-by-step:
1. Disconnect the Negative Cable from the Battery.
2. Using a 15mm closed end wrench/bar - Rotate the Belt Tensioner towards the front of the vehicle and remove the Surpentine Belt off the Alternator. You do not have to take it completely off the vehicle.
3. Remove the bolt holding the top of the Alternator Mounting Bracket to the Engine Air Intake.
4. Remove the bolts (plural) holding the outside of the Alternator Mounting Bracket to the Alternator Mounting Plate.
5. Remove the bolt holding the top of the Alternator to Alternator Mounting Bracket.
6. Remove the Alternator Mounting Plate.
7. Remove the the Altenator Mouting Bracket.
8. Rotate the Alternator towards the rear.
9. Discoonect the electrical connections (plural), including the nut holding the wire on.
10. Remove the lower Pivot bolt located at the bottom of the alternator.
11. Remove the alternator.
12. Installation is reverse of above.
Let me know if this helped, or if you have additional information or questions. Feel free to contact me at FixYa.com!

Jan 11, 2010 | 1999 Plymouth Voyager

1 Answer

How to remove the alternator


Before the step-by-step instructions I want to make sure this is the Alternator that needs to be replaced and not something else. This will save you money for an Alternator you don't need and save you time for replacing a good alternator.
Start the vehicle. With the engine running - disconnect the Negative Cable from the Battery. If the Engine dies - it is the Alternator. If it doesn't die - it is not the Alternator. I have had plenty of people who have replaced perfectly good Alternators only to find out it was something else.
Step-by-step:
1. Disconnect the Negative Cable from the Battery.
2. Using a 15mm closed end wrench/bar - Rotate the Belt Tensioner towards the front of the vehicle and remove the Surpentine Belt off the Alternator. You do not have to take it completely off the vehicle.
3. Remove the bolt holding the top of the Alternator Mounting Bracket to the Engine Intake.
4. Remove the bolts (plural) holding the outside of the Alternator Mounting Bracket to the Alternator Mounting Plate.
5. Remove the bolt holding the top of the Alternator to Alternator Mounting Bracket.
6. Remove the Alternator Mounting Plate.
7. Remove the the Altenator Mouting Bracket.
8. Rotate the Alternator towards the rear.
9. Discoonect the electrical connections (plural), including the nut holding the wire on.
10. Remove the lower Pivot bolt located at the bottom of the alternator.
11. Remove the alternator.
12. Installation is reverse of above.
Let me know if this helped, or if you have additional information or questions. Feel free to contact me at FixYa.com!

Dec 15, 2009 | 1999 Plymouth Voyager

1 Answer

Removing the spoiler with the 3rd brakelight in it on a 2005 equi


THERE MUST BE ANOTHER SMALL BOLT THERE MAY BE ONE YOU HAVE MISSED IT THE MIDDLE MOST PROB.. THERE IS SOME TIME 2 IN THE MIDDLE AREA

Apr 07, 2009 | 2005 Chevrolet Equinox

2 Answers

I need to change my starter on my Hyundai 1995 Accent I can't see where it is I would need a schema on how to remove a starter on Hyundai 1995 Accent. If you don't have a schema please explain the better...


your starter always going to be somewhere near the flywheel of your vehicle it might be on the bottom or something but just take a look where your batter cables go and alternator cables follow them and they may lead you to the starter

Mar 15, 2009 | Hyundai Motor 1995 Accent

1 Answer

I need to remove a crankshaft pulley


Remove the starter and use something to hold the flywheel in place. There is actually a special tool that bolts onto the starter bolt holes with teeth that will do this for you but if you use your imagination and possibly a helper you can get the bolt loose. In the past I have used a prybar (large screwdriver) with a person holding it in the teeth and then someone else removing bolt. Use something sturdy as it has a lot of torque holding it on.

Aug 13, 2008 | 2002 Chevrolet Impala

Not finding what you are looking for?
2007 Hummer H3X Logo

Related Topics:

403 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hummer Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Brandon Johnson
Brandon Johnson

Level 2 Expert

251 Answers

Are you a Hummer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...