Question about 1994 Dodge Intrepid

1 Answer

Where are the cam sensor and crank sensors located on my car?

I need a diagram showing where the cam sensor and crank sensors are located on a 1994 Dodge Intrepid 3.5l!?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 16 Answers

Crank Sensor: Passenger side of transmission just to right and above the differential cover. Has 3 wires:

Light Blue/Dark Blue stripe - Signal
Dark Red - 8v supply
Black/Light Blue stripe - Ground

If the car runs or cranks, you can test this sensor by first checking for power on RED wire with key ON. Should be 8-9.5 volts DC. Furthermore, connect a dwell meter to the signal wire by probing the back of the connector. Dwell reading should be 49-51%. If not, its likely bad.

If you remove the sensor, you MUST replace the paper spacer on the end of the sensor or you risk damaging the sensor or even the torque converter drive plate otherwise. Also make sure O-ring is in good shape and positioned properly.

Cam Sensor:
Facing Engine, it is on the driver side timing case housing, on top of the round part, just to the right of the fuel rail pipe where there is a capped fuel valve.

Has 3 wires:

Tan/Yellow stripe - Signal
Dark Red - 8v supply
Black/Light Blue stripe - Ground

Testing is same as for Crank Sensor.

Posted on May 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to know how many sensor. is on my transmission.. 2003 Pontiac Montana v 6 .. can you show me picture where transmission control solenoid goes?


There are 12 common sensors and 10 internal sensors. The most common that often fail (MAP), (TPS), (CAM), (IGN), (CRANK) MAP is your mass air flow which is located at the beginning of your air intake, TPS is the throttle body position sensor, the CAM is the cam shaft position sensor (transmission), IGN ignition position sensor and the CRANK sensor is located near the bottom driver side front

Oct 26, 2013 | 2003 Pontiac Montana

1 Answer

1999 tahoe crank/cam sensor?


the 5.3 and 6.0 are famous for bad crank sensor. never a problem with cam sensor. the crank sensor is located behind the starter. you need to remove starter to get to it. ther is one bolt holding it in. check the wires going to the sensor because they are so close to the exhaust the get brittle and brake. if the wire is good change sensor and your car will run fine

Mar 21, 2013 | 1999 Chevrolet Tahoe

1 Answer

Timind belt diagram


i would say your looking at a faulty cam shaft sensor..its located on front side of engine. this fixed the same problem i had..there are 2 sensors one being your cam shaft sensor (normal to go out) and the crank shaft sensor..these work inline with computer to determine correct timing.hope this helps

Dec 07, 2011 | 2000 Ford Escort

1 Answer

Where is located the cam position sensor on a 94 Toyota previa?


up to 1994 Previa's the cam sensors are located in the distributor, there is one for each cam. labeled G1 & G2 which are the center 2 of the 4 wires to the distributor, if you want to test them first.
Also, top wire is crank sensor, bottom is ground.

I believe you will have to replace the whole distributor.

Nov 13, 2011 | 1994 Toyota Previa

2 Answers

Where the cam and crank sensors on the 07 cobalt lt


Hello foster_renar,

If you have the 2.2 or the 2.4 engine the diagram below shows 7 as the cam sensir and 10 as the crank sensor.

netvan_184.png

I hop this helps.

Regards,

netvan

Aug 20, 2011 | 2007 Chevrolet Cobalt Coupe

1 Answer

Where is your cam position sensor located? and where is the crank shaft position sensor at?And could you send a diagrm or something to show?


the cam sensor is located on top of the engine in the front of the left side valve cover. the crank sensor is located on the right side of the engine block just above the starter.

Jul 17, 2011 | 2000 Chrysler Concorde

1 Answer

Truck quit running, is getting fuel, spark, timing is dead on, local shop said it may be crank pos sensor or cam pos sensor,where are they located/


Very possible. I would check the sensor with a meter. I would say it most likely the crank shaft sensor. Some are located behind the pulley area and some are located at the back of the engine where the transmission meets the engine. Good Luck

Mar 04, 2011 | 1994 Dodge Ram 2500

2 Answers

Jaguar xj 40 sovereign 1994 error code 17


I'm not a Jag expert, but error code 17 is:
P0017 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B)
Additional infomation on and cause and possible solutions are here:
http://www.obd-codes.com/p0016
Basically, it looks like you have timing issue. Could be the cam or crank sensor or the timing belt.
The P0017 code would imply that you have at least two cam sensors (V6 or V8). The computer thinks that the B sensor cam is out of time with the other cam and the crankshaft. Depending on the cost and location, you might try changing the cam sensor first. The cost to check or replace the timing belt is probably going to be painful.

Jun 12, 2010 | 1994 Jaguar XJ6

1 Answer

Trying to locate cam sensor


the cam sensor is located on the front of the engine below the power steering pump, if you look under the power steering pump, look from the front side you will see crank sensor, heres a diagram its not labeled but if you look were the ps pump would sit you can see the wire from the cam sensor, hope this helps.9d786bd.gif

Feb 28, 2010 | 2001 Oldsmobile Silhouette

Not finding what you are looking for?
1994 Dodge Intrepid Logo

371 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...