Question about 2006 Datsun Pulsar

Open Question

Carburator assembly Datsun 1400 ditacy carburator have a metal wait where must this part fit.float levil is ok but the carburator keep on flating

Posted by on

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can i find a picture of an assembled carburator for n nissan 1400 bakkie?


If you mean a carburettor then check with nissan = they will happily email you pictures from their extensive archive, i had a similar issue when looking for assembled engine for my Terrano

Nov 11, 2014 | Cars & Trucks

1 Answer

Car do not want to start petrol not going to the carburator


The carb has to be serviced. Could be clogged filter to the carb reservoir or the float system needle is stuck closed. The reservoir has a float similar to a toilet cistern.

Jan 30, 2014 | 2004 Citroen Xsara Picasso

1 Answer

CARBURATOR OF NISSAN 1400 BAKKIE


the ball bearing will be a non return valve for the accelerator pump. When the pump is moved to suck in fuel from the bowl it lifts of the seat and when the pump is pressed down the force of the fuel closes it off and the fuel is squirted in to the manifold.

Jan 19, 2014 | Nissan Cars & Trucks

1 Answer

What is it when I am going up hill and step on the gas the truck starts cutting out?


Inside your carburator is a mini gas tank (float bowl) that keeps a specific amount of gas in reserve to accommodate changes. It isn't getting enough gas. The most likely culprit would be the fuel filter, so get it changed first. If that doesn't make the problem go away then the fuel pump is likely getting weak and not pushing enough gas into the carb. You can get it tested before you change it to make sure. If it tests good or you change it and still have the problem you will have to get the carburator taken off and rebuilt. Over time there will be a certain amount of crud acumulate in the float bowl that is interfering with gas delivery or it's also possible the float has become "waterlogged" and is not keeping gas at the proper level. Rebuilding carburators is not a job for rookies. It may cost more up front to have it done by a shop, but it will save you a lot of grief in the end.Hope this helps.

Oct 29, 2011 | 1985 Nissan Pickup

1 Answer

Carburator is overflowing out air vents


Check if the float still floats...
When replacing the top cover, look out that no needle pushes the float down.
I don't know if a clip should be there. In case off, you'll se a trace of it.

Nov 01, 2009 | 1983 Buick Riviera

1 Answer

Truck starts, but has a hard time staying running. smells like gas under hood and smokes. could my carburetor be bad?


I wouldn't say that the carburator is bad, but it may have some defective components in it, like a sticking float or leaking gasket. Can you see any fuel leaking in or around the carb? You can purchase a carburator rebuild kit at most autoparts stores. You must have the right number for the carb. There is usually a metal tag attached under one of the bolts that hold the carb to the throttle body that will have the number on it and sometimes it is stamped on the carburator body. Before you dig into the carburator, however, check for more mundane causes, like a faulty or fouled spark plug. Hope this helped and best wishes.

Jul 31, 2009 | 1982 Ford F 150

1 Answer

Were is the float chamber on i honda civic


The float chamber is in the underside of the carburator if this is a carburated car.
If the float is in fact shutting off the fuel to the carburator the engine should still run on the fuel in the float bowl. Unless it is a very long sharp turn. Have you tried standing still and just turning the wheel hard to the right and see id the engine cuts out ? If it does you may have an exposed wire that touches somewhere when steering is all the way over to one side.
Hope this helps
Sam

May 13, 2009 | 1986 Honda Civic

2 Answers

New carburator and it runs worse


Check your fuel pump,it sounds as if you have excessive fuel pressure.

May 05, 2009 | 1984 Ford F 250

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Datsun Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Datsun Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...