Question about 1986 Volkswagen GTI

1 Answer

Need to know the placement of the altenator belt for a ford range

I just replaced my altenator in my Ford Ranger but having trouble with the placement of the belt. Is there a diagram for it, or can you just tell me how it's placed?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,959 Answers

CLick on the link below, insert the year and make of the truck and click on the belt you're replacing and you'll get a diagram. Best of luck!
Greg
http://www.mvreader.com/multiview/dayco/index.php?bgInterchange=1&l=n

Posted on May 14, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What could cause an altenator not to get power


Alternators give charge not get a charge. Check that you have connected up the wires to the alternator correctly. Check drive belt for tension and condition. If it still will not charge have a qualified auto electrician check it over.

Nov 12, 2013 | 1987 Ford Ranger

1 Answer

1998 ford ranger with 2.5 4 cylinder engine timing belt broke need to replace it need to know correct placement of timing marks on camshaft


If the belt broke then the head will have to come off because the valves will be bent. Talk to the re-conditioner shop and they will explain where the marks are and how to do the job.

Sep 22, 2013 | Cars & Trucks

1 Answer

I have a 1993 ford ranger xlt and i need to change the altenator


Go to Autozone website and key in info about vehicle. Make sure you know whether it is 2.3, 3.0, or 4.0 motor. Picture of part will show you where mounting bolts are located as well as location of "hot" wire connection and pigtail. Remember to disconnect the battery before you do anything to the electrical system. Website also has a how to on replacing this part. Good luck!

Jan 12, 2013 | 1987 Ford Ranger

1 Answer

HOW DO I TAKE TENSION OFF OF BELT TO REPLACE ALTENATOR ON 2003 4.0 FORD RANGER


when you unbolt the alternator it will slide and loosen the tension. Good Luck Tim

Mar 25, 2011 | Ford Ranger Cars & Trucks

1 Answer

When i accelerate the battery light comes on the dash and the needle goes to high side in moy 02 ford ranger 4.0 i changed the battery, altenator, and belt what could it be?


This sounds like a voltage regulator problem, the voltage regulator is built into the altenator, check your connections to the altenator specfically the ones that plug in, make sure they are secure. The plug in connections provide signal for how much output is needed from the altenator, the regulator provides the output. Check the battery voltage with a voltmeter, turn on everything electrical, rev up engine and see if voltage goes over 14.5 volts, it should be steady. Hope this helps, let me know.

Aug 04, 2010 | 1991 Ford Ranger Supercab

1 Answer

I keep having problems with my waterpump on my 99 ford ranger. I've replaced it twice and Im still having trouble with it


if its over heating its probably the thermostat or if water pump keeps going bad then there is too much tension on the belt.

Jan 15, 2010 | 1999 Ford Ranger SuperCab

1 Answer

The timing belt is broke, how can reemplace and


Take off the alternator belt, tensor, fan and cap of timing belt, review the mark of cranshaft pulley must be in 10grades BTC The grades are on the cap, then review the mark valves pulley and put the timing belt (Note disconect the battery in order to delete the failure) placement again all the parts and thats all.

Jan 12, 2010 | 1991 Ford Ranger Supercab

1 Answer

Dont know correct placement of spark plug wires


try here...
http://autorepair.about.com/library/firing_orders/bl-ford-firing-03.htm

Apr 22, 2009 | 2003 Ford Ranger Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76070 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...