Question about 2000 Chevrolet Express Cargo

1 Answer

I have a 2000 chevy express 1500. I turn the tail lights on all 4 lights go on, I step on the brakes the lower lights go off and the upper lights do not get any brighter If the tail light are off and I step on the brake the lower lights come on but at the lower brightness. The 3rd light works in all situations thanks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Chevrolet Master
  • 2,007 Answers

If you have an aftermarket trailer plug on there, disconnect it. The wires are probably bare or the plug in itself is corroded. If it's not that then you have bare wires shorting out somewhere back there.

Posted on May 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

95 Chevy pickup 1500 with a 4.3 if you turn the head lights on or step on the brakes it stalls. But you can turn on the dome lights and heater control and it's ok. I have gone through the tail light...


check alternator drive belt for condition and tension. check for alternator out put. Have a load test done on the battery. From your description when heavy current draw items ( head lights , brake lights ) there is insufficient current available to run the ecm and power the ignition system.

Jan 25, 2015 | Cars & Trucks

1 Answer

2000 chevy express van, no brake lights; left, right and above rear door. Tail lights good and signals all work.


probably a fuse. if the fuses are good check the brake light switch on the brake pedal.

Mar 10, 2014 | 1998 Chevrolet Express

2 Answers

Need torque specs for 2000 chevy malibu 3.1 cyl heads & intake


(step 1 ) the torque specs for the heads are---1998 through 2001 are 37 foot lbs. ( step 2) rotate an additional 90-degrees (1/4 turn). intake manifold bolts ( lower ) step 1-- 62 in-lbs, step 2--115 in-lbs. intake manifold bolts/studs ( upper ) 18 ft-lbs. this is for the 3.1 v-6, have a good day!

Aug 14, 2010 | 2000 Chevrolet Malibu

2 Answers

How to replace brake light in 2008 chevy express cargo van


You have to remove the upper applique to remove the tail lamp, it is the trim panel above the lamp. I think it is held in place by two nuts/bolts but not sure. You have to have the rear doors open to remove it

May 23, 2010 | 2008 Chevrolet Express

1 Answer

2000 chevy express 1500 van having starting issues


Start with fuel system. Listen for fuel pump humm at fuel tank No humm check wiring to pump for power. Then check for spark at plugs and wires. Remove wire from coil and hold near engine and see arch when you crank. No arch. Replace ignition Modular inside distributor cap or cap or rotor

Feb 04, 2010 | 2000 Chevrolet Express Cargo

2 Answers

Chevy express 1500 can 2500 coil springs fit or the leave spri


yes they will fit. be careful use all the suspension parts, life springs coils a-arms upper lowers its a all day projected get a coil spring compresser

Jan 29, 2010 | 2000 Chevrolet Express Cargo

1 Answer

Upper and lower ball joint replacement


to remove the axles, remove brake caliper and disc, remove hub assembly, the center hub/axle nut and...(there are i think 3-4 bolts on the back side of the spindle to remove the hub), you may have to force the hub off the spindle with a hammer or air hammer... once the hub is out the axle should slide out of the front differential allowing access to the ball joint nuts for removal...

Jun 12, 2009 | 2000 Dodge Ram 1500 Truck

1 Answer

Brake light problem


My van did the same thing it was the ground at the socket it had a good ground all the way to the socket but lost it right at the socket.

May 14, 2009 | 2000 Chevrolet Express Cargo

Not finding what you are looking for?
Cars & Trucks Logo

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...