Question about 1995 Ford Windstar

1 Answer

Need directions for replacing right axle shaft on 1995 windstar.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Jack up ur car properly plz bcuz u will have 2go underneath!! u take the tyre off, on da front orb u will c a nut i think its a size 30 -32 take it off. on the shock there is a to bolt take them off u will pull da orb up or on the side. get a big flat screw driver r a prybar put it at the end off da axle dats by the tranny dan just pry it off.

Posted on May 28, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace 2006 ford escape left front axle shaft


How to Replace a CV Axle on a Ford Escape / Mazda ...

? 9:41
https://www.youtube.com/watch?v=_JxagNLBlQ4
Aug 29, 2013 - Uploaded by klowny1969
Axle nut should be torqued to spec..in the ford escape its around 205-220 lbs ft How To Change An Axle On A Front Wheel Drive Car ! SUBSCRIBE ! ... How to Replace a Front Axle Half Shaft - Duration: 14:37. ... Alternator replacement 2005 2006 Ford Escape 3.0L DOHC All Wheel Drive - Duration: 13:15.

Front axle replacement Ford Escape 2003 Right front CV ...

? 8:46
https://www.youtube.com/watch?v=JQK8SPj6Qsk
Mar 29, 2014 - Uploaded by Fixing cars and stuff
Front axle replacement Ford Escape 2003 Right front CV axle install remove replace This Channel provides ...

Feb 03, 2016 | Ford Cars & Trucks

2 Answers

97 ford windstar leaking transmission fluid


Possible leaks are 1. Transmission belly Pan gasket 2. Front pump/torque converter seal. 3. Transmission fluid cooler lines 4. Axle seals at right and left half shafts.

Feb 13, 2012 | 1997 Ford Windstar

1 Answer

My 1995 Geo Prizm. I hear noise at the left side of the transmission where the drive axle enter the transmission not the usual clicking sound when the drive axle goes bad. The noise show up when I...


I would still suspect the drive axle because it could very well be the inner joint of the axle clicking and not making the accustomed noises related to a drive shaft noise.Thanks Megabuck

Aug 29, 2011 | 1995 Geo Prizm

1 Answer

Replace left front axle seal


First you'll have to remove the axle shaft, and here's detailed directions so use whatever info you need. First you'll need to jack up your vehicle place your jack just behind the front lower control arm mount. Take off your tire/wheel, remove the cotter pin and the axle nut retainer, remove the 2 caliper mounting bolts, move the caliper out of the way and support it so it doesn't just hang by the brake hose. Now, slide your rotor off, next you'll need to remove the axle nut and at 180ft lbs of torque you'll need a breaker bar or a heavy duty impact. The nut should be a 36mm if I remember correctly. Remove the bolts holding hub to steering knuckle, remove hub now you can tap it with a hammer to help loosen it from splines on axle shaft. take off the dust cover, pull the axle shaft out now, take out your bad oil seal, grease splines, then install new seal, carefully reinstall axle shaft to avoid damaging the seal, reverse steps and you're good to go. Good luck with your repair

Jan 29, 2011 | 1995 Jeep Grand Cherokee

1 Answer

I need to know if special tools are needed to replace the drivers side CV joint on my 2000 Ford Windstar.


I would buy a rebuilt axle half shaft from your parts store and replace. It is cheaper than CV, boot. grease, and seal And, you have new CV's on each end of axle half shaft, not 1.

Aug 04, 2010 | 2000 Ford Windstar

1 Answer

Steering noise when turning right


Sounds like 1 bad CV joint. Not sure which side. Look at the front axles, and if 1 or more of the boots are torn then that one is most likely the culprit. If you can grab the axles, feel for free plat. A decent shop will be able to pinpoint the bad CV joint and either grease it and replace the boot, or more likely, replace the complete axle on the bad side.

Jul 10, 2010 | 2001 Ford Windstar

2 Answers

CANT FIND WHERE THE SPEED SENSOR IS NO MY 1995 OLDSMOBILE AURORA


hi , their is two different speed sensors on your vehicle one is the input speed sensor which is inside the transmission and the transmission will have to be removed to replace it the other one s the output speed sensor is located directly above the passenger side trans-axle shaft. your input sensor is the sensor which tells the transmission when to shift and the output speed sensor tells the speedometer what it should display and both those parts are fairly cheap they are around 15-25 dollars but just remember if your input speed sensor is bad it is gonna cost you a minimum of 1000 dollars to have a mechanic fix as the transmission needs to be removed hope this is what you needed

Jun 06, 2010 | 1995 Oldsmobile Aurora

1 Answer

Cannot find the vss in my 95 windstar .What is the easiest way to change this15 dollar part i cannot find lol


According to the diagrams I can find it appears to be in the right side output shaft tube on the right hand side of the van. This is not an easy change, good luck with it.

Jun 09, 2009 | 1995 Ford Windstar

1 Answer

I am trying to find a diagram for belt for a 1995 Ford Windstar


i dont have a diagram but know how it goes on. from the passenger side of the van starting at the crank shaft. it goes from the crank shaft to the ac pump straight up to the power steering pump down to the ideler pully then back up to altinator then down aroun the water pump then over to the tensioner and back down to the crank saft

Mar 30, 2009 | 1995 Ford Windstar

1 Answer

83 cj7 rear axle


You could weld the keyway and file it back to size or replace axle. To upgrade, check with some of the big axle manufacturers like strange engineering etc. They could likely help or point you in the right direction. Anything you do will be $$ though.

Feb 22, 2009 | 1984 Jeep CJ7

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...