Question about 1981 Chevrolet Corvette

1 Answer

I have an 81 vette and the power lock lock the door but will not unlock?

Posted by on

  • gennarelli May 14, 2009

    yes getting power to solenoid. having this issue with both doors.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 957 Answers

Are you getting power to the solenoid when you press lock/unlock? If you are, because of the age I would suggest looking at the door latch asm.'s. They are known to rust up and cause malfunctions.

Posted on May 14, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What fuse is it for rear hatch actuator 99envoy


One fuse powers all door lock actuators . The other door locks work ? if so it's not a fues problem .
The following locking functions are included on the vehicle:
• All the doors unlock -- All the doors will unlock, including the endgate/liftgate, when any power door unlock switch is detected. The passenger doors lock directly by pressing the lock switches. The driver door unlocks by the BCM using a driver door unlock relay.
• All the doors lock -- All the doors will lock, including the endgate/liftgate, when any power door lock switch is activated. All the lock actuators will activate directly from the power door lock switch (external to the BCM).
• The end/lift gate lock switch -- All the doors will lock or unlock from the end/lift gate lock switch

You probably have a bad lock actuator

Jun 14, 2017 | Cars & Trucks

1 Answer

Where are the fuses for the power dock locks on a 2006 montecarlo06ss


DR/LCK fuse 25 amp . located in the I/P block
Fuse Block - I/P
In the right front kick panel

Power Door Locks System Components
The power lock system consists of the following components:
• Body control module (BCM)
• Driver door lock cylinder switch
• Front passenger door lock cylinder switch
• Driver door lock switch
• Front passenger door lock switch
• Door lock actuators in each of the doors
• DR LK Fuse 20-amp
Door Lock System Controls
The Power Door Lock System is controlled by the body control module (BCM) and can be activated by any one of the following:
• A door lock switch lock or unlock actuation
• A door lock cylinder switch unlock actuation
• A keyless entry transmitter actuation
• An automatic door lock actuation (Personalization function)
• An automatic door unlock actuation (Personalization function)
Door Lock Operation
When the body control module (BCM) detects a transition of either of the door lock switches to the lock position, it switches the door lock actuator lock control circuit to voltage. Since the lock actuator unlock control circuits are at ground potential within the BCM, the door lock actuator motors transition to the lock position.
Driver Door Unlock Operation
When the body control module (BCM) detects a transition of either of the door lock switches to the unlock position, it switches the driver door lock actuator unlock control circuit to voltage. Since the door lock actuator lock control circuit is at ground potential within the BCM, the left front (LF) door lock actuator motor transitions to the Unlock position.
The driver door lock actuator unlock control circuit is a dedicated control circuit used only for the driver door lock actuator motor. This is done so that the driver door may be unlocked by itself using a keyless entry transmitter or an automatic door unlock function (if programmed).
Passenger Door Unlock Operation
When the body control module (BCM) detects a transition of either of the door lock switches to the unlock position, it switches the door lock actuator unlock control circuits to voltage. Since the door lock actuator lock control circuit is at ground potential within the BCM, the passenger door lock actuator motors transition to the unlock position.
The door lock actuator unlock control circuits are dedicated control circuits used only for the passenger door lock actuator motors. This is done so that the driver door may be unlocked separate from the passenger doors using a keyless entry transmitter or an automatic door unlock function (if programmed).

Mar 23, 2017 | 2006 Chevrolet Monte Carlo

1 Answer

Why does my 2004 Chevy Silverado lock and unlock while in drive? When turned off and no keys in ignition the drivers door will unlock on its own a short time later.


Gremlins ! HA HA HA sorry ! First off a little bit on how they work an what all is involved in making them work ! There are a few control modules in the mix , switches ,relays etc...
Door Lock System Components
The power door lock system consists of the following components:
?€¢
The driver door module (DDM)

?€¢
The passenger door module (PDM)

?€¢
The body control module (BCM)

?€¢
The driver information center (DIC)

?€¢
The rear door lock switch

?€¢
The door lock relay

?€¢
The door unlock relay

?€¢
The liftgate lock relay--utility vehicles with liftgate only

?€¢
The reversible door lock actuators in each of the doors and liftgate

?€¢
LOCKS 20A fuse (rear lock/unlock relay supply voltage)

?€¢
ECC 10A fuse (liftgate lock relay supply voltage)

Door Lock System Controls
The power door lock system can be controlled by any of the following:
?€¢
A power door lock or unlock switch activation

?€¢
A keyless entry transmission

?€¢
An automatic door lock function

?€¢
A delay lock function

?€¢
Door lock cylinder switch activation

?€¢
Lockout Prevention

?€¢
An airbag deployment

The front power door lock switches are integral components of the driver door module (DDM) and passenger door module (PDM). The switches are two position normally open rocker switches. When placed in either the lock or unlock positions, the switches provide a direct input to the DDM or PDM. The DDM or PDM monitors these inputs and sends a Class 2 message indicating a change in the switch's respective position. Modules which activate the power door lock motors receive the Class 2 message and activate the motor in the appropriate direction to lock or unlock the vehicle's doors and liftgate. The rear door lock switch provides a lock and unlock signal to the body control module (BCM). The BCM upon receipt of a lock or unlock signal will control the rear door lock relays and also send a Class 2 message to the DDM and PDM to perform the appropriate function.
The modules which activate the power lock motors are:
?€¢
The DDM (driver door lock actuator).

?€¢
The PDM (passenger front door lock actuator).

?€¢
The BCM (both rear door lock actuators and cargo door/liftgate).
The DDM and PDM are directly connected to the respective door lock actuator through the door lock motor lock and unlock circuits. Once a door lock or unlock request has been received, the module will supply battery voltage to one side of the actuator and ground the other causing the doors to lock or unlock.
The rear passenger and cargo doors differ slightly in that they use lock and unlock relays. The relays supply and coil sides receive a constant voltage through the battery voltage supply circuit. The normally closed contacts are connected to ground and the control side is connected to the BCM. Once a door lock or unlock request has been received by the BCM, the BCM will ground the control side of the appropriate relay. This energizes the relay and allows voltage to be applied to either the door lock motor lock or unlock circuits. since the other side of the door lock actuator is connected to the normally closed contacts of the opposing relay to ground, the doors lock or unlock.
The first place to start is have a factory or equivalent scan tool hooked up , one that can read BCM DTC'S - diagnostic trouble codes ! This could lead to a fix faster ! Watch these three videos !
Door Locks Go Crazy 1

Sep 16, 2015 | Cars & Trucks

1 Answer

Door lock dont always work


What door lock doesn't always work ? One or all of them . This is a complex set up for these door locks ! The switch is an input to the BCM - body control module . There is logic involved in the microprocessor , there are relays built in to the BCM ! Could have a DTC - diagnostic trouble code stored in the BCM ! Could be a bad connection at the BCM or master window switch ! A bad ground !
The power door lock system consists of the following components:
?€¢
Body control module (BCM)


?€¢
DOOR LKS fuse


?€¢
Driver door lock actuator


?€¢
Driver door lock switch


?€¢
GMLAN serial data link


?€¢
Keyless entry transmitter


?€¢
Passenger door lock actuator


?€¢
Passenger door lock switch


?€¢
Remote control door lock receiver (RCDLR)


The DR LCK fuse supplies battery voltage to the body control module (BCM) for the power door lock system. The BCM supplies and monitors a reference voltage to the driver and passenger door lock switches through the door lock switch lock/unlock signal circuit. Each door lock switch receives ground at G300 which is also the ground for the door lock and unlock relays located in the BCM. When a door lock switch is placed in the lock position, the reference voltage is switched to ground and the BCM senses 0.0 volts on the door lock/unlock signal circuit. When a door lock switch is placed in the unlock position, the reference voltage is switched to ground through a 1.5k ohm resistor that is internal to each of the door lock switches and the BCM senses approximately 2.9 volts on the door lock/unlock signal circuit. The BCM interprets what position the activated door lock switch was placed in based on the voltage drop.
The BCM, upon receipt of a lock or unlock switch signal, will switch the appropriate door lock/unlock relay coil control circuit to ground causing the appropriate door lock/unlock relay to energize. With the relay energized, voltage is applied to the door lock actuator control circuit causing the door to either lock, or unlock depending on what command was received from the power door lock switch or remote control door lock receiver (RCDLR). When a power door lock/unlock relay is not energized, the switch contacts are normally grounded through the BCM which provides ground to the appropriate door lock actuator for the lock/unlock function being performed. The power door lock/unlock functions are performed by reversing the flow of voltage through the door lock actuator control circuits. The BCM has three internal drivers for the power door lock system. Driver door unlock, passenger door unlock and all door lock. This is done to isolate the driver door lock actuator so it can be unlocked separately from the passenger door. For additional information concerning keyless entry, refer to Keyless Entry System Description and Operation.
This is one you may want to take to dealer or some other ASE certified repair shop ! To do this right you need a Tech 2 scan tool !
Ignition ON, observe the scan tool Door Lock Switch parameter while using the driver and passenger door lock switches. The parameter should change from Idle to Lock and Unlock.
?‡'
If the value does not change, refer to Door Lock Switch Malfunction.

Command the doors to LOCK and UNLOCK with the scan tool, the door lock actuators should LOCK and UNLOCK when changing between the commanded states.
?‡'
If one or more doors do not LOCK or UNLOCK, refer to Door Lock Malfunction.

Aug 12, 2015 | 2009 Pontiac Solstice Convertible

2 Answers

What causes a malfunction in power locks?


The power door locks are controlled by the BCM -body control module ! The door lock switch is an input to the BCM .
The BCM, upon receipt of a door lock switch lock or unlock signal, will switch the appropriate door lock actuator control circuits to battery positive voltage. The opposing side of the door lock actuators are connected to ground internally within the BCM through the other door lock actuator control circuit and the doors will lock or unlock appropriately.
First thing to do would be check power an ground circuits at the BCM ! Do you have any other systems not working -power windows etc...
The DR/LCK fuse supplies battery positive voltage to the I/P fuse block for the door lock system. The body control module (BCM) supplies and monitors a reference voltage to the door lock switch through the door lock switch lock/unlock signal circuit. The door lock switch also receives a constant ground source. If a door lock switch is placed in the lock position or unlock position, the reference voltage is taken directly to ground and the BCM detects the voltage drop on the signal circuit.
Should have BCM checked for stored DTC'S - diagnostic trouble codes !
Ignition ON, observe the scan tool Driver Door Lock Sw, Psgr Door Lock Sw, Driver Door Unlock Sw and Psgr Door Unlock Sw parameters while using the driver and passenger door lock switches. The parameters should change between Active and Inactive.
?‡'
If the values does not change between the commanded states, refer to Door Lock Switch Malfunction.

Command the driver door and passenger door lock actuators to LOCK and UNLOCK with the scan tool, the doors should LOCK and UNLOCK when changing between commanded states.
?‡'
If a door lock actuator does not perform the LOCK and UNLOCK functions, refer to Door Lock Malfunction


DTC B3130 00: All Door Unlock Circuit

DTC B3135 00: All Door Lock Circuit

Aug 09, 2015 | 2010 Chevrolet Impala

2 Answers

Why won't the passenger door unlock?


Door Lock System Controls
The Power Door Lock System is controlled by the body control module (BCM) and can be activated by any one of the following:
?€¢
A door lock switch lock or unlock actuation

?€¢
A keyless entry transmitter actuation

?€¢
An automatic door lock or unlock actuation

?€¢
A last door closed locking (LDCL) actuation
If the driver door cylinder switch feature of the vehicle is functional, the locks may also be operated by a driver door cylinder switch lock or unlock activation.
Power Door Lock Switch Operation
Each door lock switch is wired to the body control module (BCM) through a separate door lock/unlock signal circuit. While these circuits are separated between the BCM and respective door lock switch, they are connected into a single circuit within the BCM. The BCM supplies voltage through the door lock/unlock signal circuits to each door lock switch. When either door lock switch is operated, this supply voltage is pulled to ground, providing the BCM with the required lock or unlock signal. In order for the BCM to distinguish between a lock and unlock signal, the lock switch contains two separate paths for this voltage to flow to the same body ground. When the switch is operated to the unlock position, the supply voltage flows to ground through a 1.5 K?© resistor. When the switch is operated to the lock position, the supply voltage flows to ground through a different part of the switch circuit, which has no resistor. The BCM then interprets the flow of voltage as a lock or unlock request and powers the door lock actuators to the appropriate lock or unlock position.
I'll post a youtube video on how to test the power door locks computer controlled , check it out ! Your problem could be a switch or the lock actuator , BCM , wiring etc.... you need to test it to see !
I'll
How to test computer controlled door locks

Mar 22, 2014 | 2008 Saturn Aura

1 Answer

Wires came loose on 81 vette elect door locks when i took panel off need to know what order to put them back them nothing in chiltons? drivers side


I'm going to guess that's it's just a two wire hook up. There's only two ways to hook it up. Try it one way and if the door locks when you press lock on the switch it's on there right, otherwise just reverse the wires.

Oct 04, 2009 | 1980 Chevrolet Corvette

1 Answer

Need wiring diagram for 80 vette power door locks


Here is a wiring diagram for the 1980 Corvette power door locks.

Link to: diagram

Hope this helps.

Mar 15, 2009 | 1980 Chevrolet Corvette

2 Answers

Sliding power doors will not open


Just had the same problem with my '05 van. I put the Master Switch in the off position. I pulled fuse #7 on the driver side sub panel, located just above the engine hood release. I then disconnected the neg. terminal on the battery. I manually opened the pass. side slider and closed it.

I reconnected the battery and replaced fuse #7. I put the master door switch in the on position. I activated the auto door switch, and it worked.

Jan 15, 2009 | 2007 Honda Odyssey

2 Answers

Drivers side door lock


is the lock mechanism siezed,or is the linkage disconected?

Jun 08, 2008 | 1999 Chevrolet K1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

152 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...