Question about 2003 Pontiac Aztek

1 Answer

Replacing side view mirror and can't get door skin off

I have a '03 aztek. i have removed the 3 torx bolts and done all i can figure without breaking anything

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 253 Answers

Useing a small screwdriver, gently pry the window switch up, and un plug it.Remove the 3 screws, then with a door panel tool start at the bottom front and pry gently out on the panel, work your way around the door. Lift up on the panel when you have all the clips loose, unplug the mirror connector. In the door right behind the mirror will be a foam pad, remove it then the 3 nuts. The mirror should come right off then. Good Luck

Posted on May 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Remove replace 05 aztek drivers side mirror assembly


I believe you have to remove the door panel to access the retaining screws. If you google aztek door panel removal there are several links that pop up to aid you in removing the panel.

Jul 30, 2016 | Cars & Trucks

4 Answers

Replace the review mirror


You need to remove the plastic plate that cover the mirror joint from the inside and undo the three bolts.

Oct 30, 2008 | 2006 Chrysler Town & Country

1 Answer

How to replace rear view mirror


Instructions
1


Disconnect your negative battery cable, if your Ford Focus has power side mirrors. If it has manual side mirrors, disconnecting the battery is unnecessary.

2


Pry off the wing mirror's inside sail panel (shaped like a triangle). Insert a trim panel tool between the door skin and the plastic panel to pry it off.





3


Carefully pull the sail panel away, minding the wiring if the mirror is power-operated. Unplug the electrical harness and set the panel aside.

4


Open the door and hold the outside part of the wing mirror steady. Remove the mounting bolt with a socket wrench, and then remove the mirror screw with a Phillips screwdriver (the mirror bolt and screw is visible with the panel removed).

5


Pull the wing mirror assembly from its mount (from the outside). Insert the replacement mirror assembly in place; tighten the bolt and the screw.

6


Attach the wiring connection to the replacement mirror. Position the sail panel in place and push it against the door to snap it back on.

Apr 18, 2012 | 2005 Ford Focus ZX3

1 Answer

I need instructions for replacing a passenger side view mirror on a 1997 Isuzu Rodeo


Side Mirrors - Power Mirror
Removal & Installation
  1. Disconnect the negative battery cable.
  2. Remove the door mirror cover (3).
  3. Remove the three bolts and disconnect the connector (2), then remove the mirror assembly (1).
  4. Installation is the reverse of the removal procedure.

    0047d6d.jpg
    Fig. View of the power mirror (1), connector (2) and cover (3)

Hope this helps.

Sep 07, 2010 | 1997 Isuzu Rodeo

1 Answer

Remove/replacing side view mirror on a jeep grand cherokee


    Remove the Old Mirror
  1. Step 1 Disconnect the negative battery cable before you take off the grand Cherokee front door trim panel. Remove all screws and clips.
  2. Step 2 Detachthe window trim cover screw, and control lever screw beforedisconnecting the entire mirror trim cover. Remove the rubber coverinside the mirror cover, and disconnect the electrical wire.
  3. Step 3 Remove three nuts from the power mirror using a Torx® star-shaped screwdriver.
  4. Step 4 Pull out the outside rear view mirror. Guide the power wire through the hole in the door.
  5. Install the New Mirror
  6. Step 1 Replace the old mirror. Put the new power mirror in place. Push the new wiring through the hole in the door.
  7. Step 2 Install and tighten the three retaining screws you took off when removing the old mirror.
  8. Step 3 Connect the power mirror wiring to the connection located on the door panel. Replace the rubber cover and interior mirror cover.
  9. Step 4 Put the front door trim panel back in place by securing all clips and tightening all screws.
  10. Step 5 Connect the Subaru Outback's battery cable to restore the power.

i will recommend i site where you will get all the information you need to remove and replace your side mirror
http://www.wjjeeps.com/mirrors.htm

Sep 10, 2009 | 2004 Jeep Grand Cherokee

1 Answer

How do I get access into the inner side of the passenger door of a 1999 suburban 1500, in order to change out the side view mirror? If that is too difficult, can I just exchange the black plastic cowling...


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Disconnect the wires / cables connecting the mirror to the controller and then you can remove the bolts holding the mirror onto the door and it'll just pop out...I've never tried to take apart the mirror itself because the clips holding the backing in the housing seem to break easily

Aug 21, 2009 | 1999 Chevrolet Suburban

2 Answers

Need to replace Mirror Assembly, 03 suburban


Your going to have to remove the inside door panel to get to the three bolts that hold the out side mirror assembly. Once you have the door panel off you'll see the three bolts that hold the mirror assembly, just un-bolt and un-clip the wire harness to the electric/heated mirror. To install the new mirror assembly, just do everything in reveres. Go to Auto Zone and by extra door panel clips, there is a good chance of breaking some of the retainer clips and Auto Zone will have the step by step instructions to replacing the mirror assembly and the removal to the door panel. Good luck and keep me posted. Be glad to help.

Jun 22, 2009 | 2001 Chevrolet Suburban

1 Answer

How to replace side mirror on 1996 GMC Sierra?


See Figure 2
0900c1528008f812.jpgFig. 2: Outside mirror-below eyeline type
  1. Remove the mirror cover screw and lift the cover and pivot the mirror towards the window.
  2. Remove the mirror to door bolts and remove the mirror and seal from the door.
  3. To install, position the mirror and seal to the door and install the retaining bolts.
  4. Pivot the mirror away from the window, and lower the mirror cover.
  5. Installation is the reverse of removal.
  Hope this helps .. if not feel free to contact me

Nov 11, 2008 | 1999 GMC Sierra

1 Answer

Driver side mirror replacement


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Oct 06, 2008 | 2004 Pontiac Aztek

3 Answers

Replacing RH Side view mirror on a 2006 Toyota Sienna


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Jul 29, 2008 | 2006 Toyota Sienna

Not finding what you are looking for?
2003 Pontiac Aztek Logo

264 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...