Question about 1999 Ford Super Duty F 550

1 Answer

My 1995 f350 doesn't spool up till about 2000 rpm's it has a 7.3 in it

Posted by on

  • its420_us May 11, 2010

    Your turbo is working just fine, what is the problem?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

My 1996 f-250 7.3 doesnt either, but it never has.

Posted on Sep 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine cranks for 8-10 seconds before it starts when engine is warm


you must RUN the SCANNER/computer for better diagnostic and fix it. YOu can have some faulty like: PCM+BCM+ignition coil, sensor, etc. see the diagram attached.
God bless you225004b9-8d42-483d-a0e8-ee6550772ecc.jpg8c2fbe48-c384-4953-ac1d-abce3867e5a4.jpg

Jul 27, 2013 | 2000 Chevrolet Astro

1 Answer

How to I remove pump on the 1995 ford f350 5.3


Remove and tag or label all hoses, so you know where they go back on.
Pull tank out from under truck, and take a wooden dowel or punch (careful of sparks) and tap the lock ring around till it can be removed. Now you can pull the pump unit from the tank.. At least, this is how you did it on older vehicles. If yours has a little different procedure, get advice, or figure it out. Good luck.

Dec 06, 2012 | 1995 Ford F350

1 Answer

2000 jetta ac dont blow cold at idle but does fine driving


There is absolutley nothing wrong with your Jetta! The compressor doesn't kick on till the engine is at 2000 rpm. It is the design not the car! I just finished my 509 certification a couple months back and noticed the same problem. Only to find out there is no problem so don't waist a whole bunch of money to fix something thats not broken its the deisgn.

Jun 21, 2012 | Jaguar XJ8 Cars & Trucks

1 Answer

2004 f350 when speeding up, lose all power to truck (radio, gauges, etc)


sound like faulty alternator voltage regulator. check alternator out put at battery with engine idling should be 13.5 - 14.5 volts at 2000 rpm if not lower you have faulty voltage regulator.also check alternator drive belt and check alternator for loose wires.besure turn off radio before disconnecting negative battery cable to keep from locking out radio losing code.

Nov 27, 2011 | 2004 Ford F350

1 Answer

My 1995 F350 Powerstroke "Shutters"


VIBRATION - DRIVELINE RESONANCE/VIBRATIONBETWEEN 1400 AND 2000 RPM WITH CONVERTER
Clutch ENGAGED DURING MEDIUM TO HEAVY
THROTTLE CONDITIONS - VEHICLES WITH 7.3L DI
TURBO ENGINE AND TRANSMISSION BUILT PRIOR
TO 11/13/95 (5L13)
^ TRANSMISSION - E40D - DRIVELINERESONANCE/VIBRATION BETWEEN 1400 AND 2000
RPM WITH CONVERTER
Clutch ENGAGED
DURING MEDIUM TO HEAVY THROTTLE
CONDITIONS - VEHICLES WITH 7.3L DI TURBO
ENGINE AND TRANSMISSION BUILT PRIOR TO
11/13/95 (5L13)

FORD:
1995-1996 E-350, F-250 CREW CAB, F-350 CREW CAB
Article 96-26-21 is being republished in its entirety as part of a consolidated 7.3L diagnostic aid booklet.
ISSUE
Some vehicles with transmissions built prior to 11/13/95 (5L13) may exhibit a driveline resonance/vibration between 1400 and 2000 RPM with the torque convertor engaged. This may be caused by the torque converter.
ACTION
Prior to torque converter replacement, refer to the following Service Procedure for details to verify conditions.
SERVICE PROCEDURE
1. Verify the resonance/vibration does not occur in neutral and is most noticeable between 1400 and 2000 RPM with the converter clutch engaged during medium to heavy throttle conditions. Also watch for the vibration to diminish at engine speeds lower than 1400 and higher than 2000 RPM. If the concern meets all of these conditions and the transmission has a built date prior to 11/13/95 (5L13), replace the torque converter. Refer to the appropriate Service Manual for removal and installation procedures.
2. If the vibration concerns do not meet the conditions, check for non-factory installed items that could affect driveline and verify proper installation. Also refer to the appropriate Service Manual, Section 05-00 for diagnosis and testing.
107118085

Aug 22, 2011 | 1995 Ford F250

1 Answer

What's the firing order for 1995 460 engine


For the 1995 Ford F350 V8: 460 cubic inch = 7.5L Engine:

Firing Order:
1-5-4-2-6-3-7-8

Cylinders:
....(back)....
|..4........8..|
|..3........7..|
|..2........6..|
|..1........5..|
.....(front)

Distributor:
....(back)
....[X]..5
...4.............1
2........O........8
...6.............7
..........3...[X] - clip
......(front)

Let me know if this helped, or if there is additional information or questions. Feel Free to contact me at FixYa.com!

Apr 27, 2010 | 1995 Ford F350

1 Answer

2004 F350 diesel no heat in cab when at idel driving or over 1000 RPM is fine


Sounds like the thermostat is not closing completly if
at all. When you're driving or running it up to 2000 rpm. the engine is working and gets warmer, at idle
no work no heat. replace the thermostat and I think
that will warm things up. Hope this helps.
Good luck.

Feb 03, 2010 | 2004 Ford F350

1 Answer

1995 ford bronco 5.8l surges while going uphill


check vacume lines, knock sensor, and air intake sensor

Feb 18, 2009 | 1995 Ford F350

1 Answer

1995 Ford F350 5spd. distributor cap wiring diagram/layout!!!


1) #1-4 pass side front to rear #5-8 drivers side front to rear
2) 1-3-7-2-6-5-4-8
3)#1 is usually marked on cap wires go ccw
4) TDC #1 cyl you must remove the shorting plug before timing
it is located by the dist plug or the ignition module small gray plug

Jul 17, 2008 | 1995 Ford F350

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...