Question about 2004 Nissan Armada
The driver side window does not work, the others do
Same problem, how did u remove the window motor
Posted on Apr 29, 2010
The power window motor has miost likely failed, pull the door panel nd replace the motor.
Posted on May 13, 2009
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
The solution to this issue was recently discovered during our most recent trip to the shop. We told them not to leave the window down when they changed the battery... BUT DID THEY LISTEN...NOOOO.
So quite by accident I was finally able to correct and then test fail the system and test and fix again...
Here you go.;
1. disconnect the battery and connect both the positive and negative cables together(after disconnected))
2. disconnect the window and lock controller in the driver's side door.
3. Leave cables connected for at least 5 minutes
4. Re-connect door window controller and locks wiring harness
5. Place the key in the ignition and turn to the run position
6. Connect Battery starting with the negative cable(ensuring not to connect then disconnect, (one swift motion)
7. open drivers side door and turn key to the off position(do not remove)
8. You should hear a series of dings
9 Once dings are heard remove the key from the ignition and you should hear the door lock solenoids activate..
10. Congrats.. Your done and the windows and locks work.
Posted on Mar 24, 2010
I promise this works 'cause I used it:
Put the key in the ignition, move the intermittent wiper control to the middle possition and then turn the key on.
just to clarify it's the ring that controlls the intermittent wiper speed and not the int / low/ high switch.
What this does is it resets the multiplex unit that controlls the accessories such as the power door locks. This problem usually happens once the battery has been removed or disconnected and reconnected. Every once in a while the multiplex systems lock up. Especially on the 98s. That's how you wake em up.
Posted on Mar 31, 2009
remove the switch and make sure there is power going to it .. then if there is, check with a tester light. if there is power going to the switch then there should be power leaving it .. If there is prepare to replace the window regulator motor ... holler if you need more.. Jerry
Posted on Apr 24, 2009
i had same problem on my jeep i disconnected the battery then reconnected everything worked fine after that
Posted on Nov 25, 2008
You can do it yourself.
Couple of times when you replace the remote battery, you might have them not working/ responding but just follow the procedure below.
Stand close to the car, hold down the open and close knobs for about 10 seconds. Press them at the same time for 3 seconds; then press the open button as the car opens.
The above procedure is applicable to a lot of car brands. It does not matter how many knobs you might have on the remote fob.
I have carried this procedure out on a lot of brands ranging from Honda, Toyota, Rover, Ford, etc. and it works perfectly well.
Good luck and Rate this.
Posted on Dec 30, 2009
Tips for a great answer:
Dec 21, 2015 | Cars & Trucks
May 24, 2014 | 2005 Mercury Mountaineer
Mar 08, 2014 | Cars & Trucks
Nov 26, 2012 | Hyundai XG350 Cars & Trucks
Oct 24, 2011 | Cars & Trucks
Aug 26, 2011 | 2009 Chevrolet HHR
Apr 24, 2011 | Lexus RX 350 Cars & Trucks
Apr 05, 2010 | 2004 Ford F150
Jan 16, 2010 | 1995 Acura Integra Coupe
Oct 06, 2009 | 2005 Honda Odyssey
1,192 people viewed this question
Usually answered in minutes!