Question about 1995 Pontiac Grand Prix

1 Answer

Timing marks On a 1995 Pontiac Grand Prix 3.1, where exactly is the timing mark on the cam sprocket? is it the hole?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,669 Answers

There should be a dot stamped in one off the teeth. If this is a used gear, you might need to clean it a little to find the dot.

Posted on May 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Timing marks 1993


spark or cam ?????????????????
and which engine, some cars have up to 10 choices.
most are about 3 or 4.
not of this can i guess.

May 29, 2014 | 1993 Pontiac Grand Prix

1 Answer

Need timing blet diagram 1992 ford ranger 2.3


Hi, the crankshaft marks are on the belt pulley and timing cover, so you have to mate it up to see them. The cam sprocket mark goes on the bottom, and aligns with another mark on the timing cover. There is a plug you pull out and hole to look thru to align the cam sprocket/shaft.


jturcotte_1801.gif


jturcotte_1802.gif


Rotate the engine so that No. 1 cylinder is at TDC on the compression stroke. Check that the timing marks are aligned on the camshaft and crankshaft pulleys. An access plug is provided in the cam belt cover so that the camshaft timing can be checked without removal of the cover or any other parts. Set the crankshaft to TDC by aligning the timing mark on the crank pulley with the TDC mark on the belt cover. Look through the access hole in the belt cover to make sure that the timing mark on the cam drive sprocket is lined up with the pointer on the inner belt cover.

Jun 01, 2011 | Ford Ranger Cars & Trucks

1 Answer

How do i set timing on 2000 dodge intrepid, i had to put water pump on now i need the timing set,


i number 1piston which is the front one on the passenger side has to be all the way up and then 60 degrees past that, there is a mark on the crank that matches up with an arrow on the oil pump housing, the driver side cam sprocket has an arrow on it, and the passenger side cam sprocket has a hole in it which is its timing mark, on the chain there are 4 gold link, a single gold link goes on the crank timing mark, a single gold link goes on the passenger cam sprocket timing mark, and the double gold links match up with the driver side cam sprocket timing mark

Aug 14, 2010 | 2000 Dodge Intrepid

2 Answers

Timming bailt marks for 1990 plym laser rs


REMOVAL & INSTALLATION 1.8L Engine
  1. If possible, position the engine so the No. 1 piston is at TDC.
  2. Disconnect the negative battery cable.
  3. Remove the timing belt covers.
  4. Remove the timing (outer) belt tensioner and remove the outer timing belt.
  5. Remove the outer crankshaft sprocket and flange.
  6. Remove the silent shaft (inner) belt tensioner and remove the belt. Fig. 1: Silent shaft belt timing marks — 1.8L engine 89573g93.gif
    Fig. 2: Checking the silent shafts for proper positioning 89573g94.gif
    Fig. 3: Timing belt timing mark alignment — 1.8L engine 89573g95.gif
    To install:
  7. Align the timing marks of the silent shaft sprockets and the crankshaft sprocket with the timing marks on the front case. Wrap the timing belt around the sprockets so there is no slack in the upper span of the belt and the timing marks are still aligned.
  8. Install the tensioner pulley and move the pulley by hand so the long side of the belt deflects about 1⁄4 in.
  9. Hold the pulley tightly so the pulley cannot rotate when the bolt is tigthened. Tighten the bolt to 15 ft. lbs. (20 Nm) and recheck the deflection amount.
  10. Install the timing belt tensioner fully toward the water pump and tighten the bolts. Place the upper end of the spring against the water pump body.
  11. Align the timing marks of the camshaft, crankshaft and oil pump sprockets with their corresponding marks on the front case or rear cover. NOTE: There is a possibility to align all timing marks and have the oil pump sprocket and silent shaft out of time, causing an engine vibration during operation. If the following step is not followed exactly, there is a 50 percent chance that the silent shaft alignment will be 180 degrees off.
  12. Before installing the timing belt, ensure that the left side (rear) silent shaft (oil pump sprocket) is in the correct position as follows:
    1. Remove the plug from the rear side of the block and insert a tool with shaft diameter of 0.31 in. (8mm) into the hole.
    2. With the timing marks still aligned, the shaft of the tool must be able to go in at least 2 1/2 in. If the tool can only go in about 1 in., the shaft is not in the correct orientation and will cause a vibration during engine operation. Remove the tool from the hole and turn the oil pump sprocket 1 complete revolution. Realign the timing marks and insert the tool. The shaft of the tool must go in at least 2 1/3 in.
    3. Recheck and realign the timing mark.
    4. Leave the tool in place to hold the silent shaft while continuing.
  13. Install the belt to the crankshaft sprocket, oil pump sprocket, then camshaft sprocket, in that order. While doing so, make sure there is no slack between the sprocket except where the tensioner is installed.
  14. Recheck the timing marks' alignment. If all are aligned, loosen the tensioner mounting bolt and allow the tensioner to apply tension to the belt.
  15. Remove the tool that is holding the silent shaft and rotate the crankshaft a distance equal to 2 teeth on the camshaft sprocket. This will allow the tensioner to automatically apply the proper tension on the belt. Do not manually overtigthen the belt or it will howl.
  16. Tigthen the lower mounting bolt first, then the upper spacer bolt.
  17. To verify correct belt tension, check that the deflection at the longest span of the belt is about 1⁄2 in.
  18. Install the timing belt covers and all related items.
  19. Connect the negative battery cable.

Aug 02, 2010 | 1990 Plymouth Laser

1 Answer

Need timing marks for a 1996 pontiac grand am se 2.4 DOHC


YOU WILL SEE A HOLE IN THE CAM GEAR THAT A 3/8 BOLT WILL FIT INTO. PUT A BOLT INTO THE HOLES OF BOTH CAM GEARS. THEN LINE UP THE CRANK PULLEY KEYWAY AT ABOUT 12 O'CLOCK WITH THE MARK ON THE ENGINE BLOCK.

MAKE SURE TO COMPRESS THE CHAIN TENSIONER AND RELEASE IT WHEN THE CHAIN IS IN POSITION.

May 31, 2009 | 2001 Pontiac Grand Am SE

1 Answer

Where are the timing chain marks ona 2000 pontiac grand am


On a 2.4, there are no timing marks...There are holes in the cam gears that need to be aligned with corresponding holes in the head.
Though it's not terribly difficult to do, it must be done precisely according to instructions or valves will hit the pistons and destroy the engine. You can find instructions for this procedure in haynes and other vehicle service manuals. (too long to write out here).
Remember...this is an exact install...you cannot just get close!!!
Good luck! Post back if you need further specific instructions with any part of the job.

Apr 23, 2009 | Pontiac Grand Am Cars & Trucks

2 Answers

Timing specs


Here is All Lititure But Pictures Wont show up on FixYa for some reason, I can Email it ALL to you Just Send Me A Request to my Nickname here @aol.com


SPECIAL TOOLS REQUIRED (or equivalents)
  • J-36008, Camshaft sprocket timing alignment pins.
  • J-39579, Camshaft sprocket wrench.
CAUTIONS:
  • The timing chain on the 1996 LD9 (VIN T) Twin Cam Engine is not to be replaced with the timing chain from any other model year. The timing sprockets are different on the Twin Cam Engine and the shape of the links matches the sprockets. Engine damage may result if the wrong timing chain is used.
  • The timing chain and crankshaft sprocket MUST be marked so that they are reinstalled with the same side facing out at the time of reassembly.
  • Failure to follow the removal and installation procedures could result in severe engine damage.
REMOVE OR DISCONNECT
  1. Negative battery cable.
  2. Front cover, refer to Timing Cover / Service and Repair .
  3. Rotate crankshaft in clockwise direction until camshaft and crankshaft timing marks are aligned.
  4. Timing chain guides.
  5. Raise and support vehicle.
  6. Ensure slack in timing chain is above tensioner assembly, then remove chain tensioner. The timing chain must be disengaged from grooves in tensioner shoe to permit removal of shoe. Position a suitable screwdriver under timing chain while pulling shoe outward. If difficulty is encountered in removing tensioner shoe, proceed as follows:
    1. Lower vehicle, then while holding the intake camshaft sprocket with J-39579, remove sprocket bolt and washer.
    2. Remove washer, then install bolt into camshaft by hand.
    3. Position a suitable three jaw puller into intake camshaft sprocket relief holes and remove sprocket. CAUTION: Do NOT pry on camshaft sprocket as damage to sprocket or timing chain housing may result.
  1. Tensioner assembly attaching bolts and tensioner assembly.
  2. MARK CRANKSHAFT SPROCKET AND TIMING CHAIN outer surface for reassembly.
  3. Timing chain.
INSTALL OR CONNECT
  1. Intake camshaft sprocket onto camshaft with surface marked during removal showing.
  2. Intake camshaft sprocket retaining bolt and washer, torque to 70 Nm (52 ft lbs) while holding the sprocket with J-39579 (if removed).
  3. Timing pins, J-36008, through holes in camshaft sprockets into holes in timing chain housing to position camshafts for proper timing. If camshafts are out of position and must be rotated more that 1/8 turn to insert timing pins:
    1. Crankshaft MUST be rotated 90°clockwise off of TDC in order to give the valves adequate clearance to open.
    2. Once the camshafts are in position and the timing pins have been installed rotate crankshaft COUNTERCLOCKWISE to TDC. CAUTION: Do NOT rotate the crankshaft clockwise to TDC, valve or piston damage could occur.
  1. Timing chain over exhaust camshaft sprocket, around idler sprocket and around crankshaft sprocket.
  2. Set camshaft sprockets at timed position and install timing chain. Remove timing pin from intake camshaft. Using J-39579, rotate the intake camshaft sprocket counterclockwise until timing chain can be installed over sprocket. Release J-39579 after timing chain has been installed over sprocket. The length of chain between intake and exhaust camshaft sprockets should tighten. The timing pin should easily fit through intake camshaft sprocket timing hole into timing chain housing timing hole. If timing pin does not fully index, the camshafts are NOT timed correctly and the procedure MUST be repeated.
  3. With timing pins installed, raise and support vehicle.
  4. With slack removed from timing chain between intake camshaft sprocket and crankshaft sprocket, timing marks on crankshaft and engine block should be aligned. If the marks are not aligned, move timing chain one tooth forward or rearward to align marks. Remove slack and recheck marks.
  5. Reload tensioner assembly to zero position as follows:
    1. Form a keeper out of heavy gauge wire into a U-shaped piece with a half inch opening.
    2. Apply slight force on tensioner blade to compress plunger.
    3. Insert small screwdriver into reset access hole and pry rachet pawl away from ratchet teeth while forcing the plunger completely in the hole.
    4. Install keeper between access hole and blade.
  1. Tensioner assembly to chain housing and recheck plunger assembly installation, noting long end is toward crankshaft.
  2. Tighten timing chain tensioner bolts to 10 Nm (89 in lbs) .
  3. Lower vehicle to point where timing pins can be removed from camshaft sprockets.
  4. Rotate crankshaft two revolutions in the clockwise direction. Align crankshaft keyway with the mark on cylinder block and reinstall timing pins through camshaft sprockets into housing timing holes. Timing pins should slide easily through timing holes. If timing pins cannot be inserted easily, repeat procedure to properly time engine. CAUTION: If the engine is not correctly timed, severe engine damage could occur.
  5. Timing chain guides.
  6. Engine front cover.
  7. Negative battery cable.

Nov 15, 2008 | 1995 Pontiac Grand Am

Not finding what you are looking for?
1995 Pontiac Grand Prix Logo

Related Topics:

177 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...