Question about 2002 Mitsubishi Lancer

1 Answer

Trouble code is gen fr.

Mitsubishi lancer. Model is ck2 engine is 4g 15. Trouble code is gen fr.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

It's your alternator (64)
1 Engine control module malfunction
11 O2 sensor malfunction (Car usually runs weak when this code appears) (If a V6 this relates to the O2 sensor on the drivers side In a 4x4 Or the one at the back of the engine on a Galant)
12 Mass air flow sensor circuit malfinction
13 Intake air temperature sensor (Comes on if you have chucked the sensor away to fit some big fancy K&N induction kit!)
14 Throttle position sensor fault
21 Engine temp sensor malfunction (Check the spark plugs too because they carbon up if this sensor is causing the car to run rich)
22 Crankshaft position sensor (Try cleaning the dirt off the end before replacing)
23 Camshaft position/distributor hall sensor (Common on Galant 1800)
24 Vehicle speed sensor
25 Barometric pressure sensor (Another name for the MAP sensor)
31 Knock sensor circuit
36 Ignition timing adjustment connector fault
41 Injectors circuit malfunction
44 Ignition coil/ignition amplifier cylinders 1 and 4
52 As above for 2 and 5 (on a V6)
53 As above for 3 and 6 (On a V6 too)
54 Immobiliser control module to engine control module malfunction (comes on if you have changed one or the other and not had them programmed in by Mitsi)
55 Idle speed control actuator malfunction (A good injector cleaner and a thrash up the motorway usually fixes this!)
59 O2 sensor (if you have a V6 this is the sensor on the passenger side ona 4x4 and the one at the front on a Galant etc.)
61 Transmission control module/engine control malfunction
62 Intake manifold air control actuator/position sensor malfunction
64 Alternator malfunction (remember to check under load and when revved up)
71 Traction control vacuum solenoid malfunction (check the pipes for leaks)
72 Traction control vent solenoid malfunction (usually blocked with dirt)

Posted on Jan 26, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 328 Answers

SOURCE: my ck2 lancer hard starts

its an injectors nozzles problem im sure of it
might be dirty nozzles needs to be cleaned and clogged up
or the nozzles are getting wider spraying hole so rather than spry the fuel it dripping it causing such a start up problems
but the sure thing is you need just check the injectors nozzles
have a nice day

Posted on May 30, 2011

  • 1 Answer

SOURCE: i have a 2000 lancer ck2 engine or 4G13 1.3, my

there's a regulator which adjusts the car rpm when ac is on
or it could be a vacuum hose check hoses

Posted on Sep 16, 2010

  • 1 Answer

SOURCE: what oil type

10W40 IS IF YOUR CAR IS OVER 120K 10W30 DURING WARM MONTHS 5W30 IN THE COLD MONTHS BUT I USE 15W30 SPECIFIED FOR HIGH REV ENGINES SUCH AS A FIVE SPEED OR MANY FOREIGN MOTORS ARE DEPENDING ON THE DRIVERS ACCELERATOR HABITS

Posted on Nov 22, 2008

  • 20 Answers

SOURCE: Mitsubishi

The following is verbatum from the mitsu engine overhaul manual... Steps 7 and 8 are a bit cryptic, but it seems like after you tighten the bolts to 20nm in the CORRECT PATTERN... you then go around tightening 1/4 turn through the pattern, then a final 1/4 turn through the pattern... do NOT tighten each bolt to 20, the 1/4 then another 1/4 before going to the next bolt, the idea is to get EVEN tightening across the head, so tighten her three times around the pattern! Now for the verbiage from Mitsu's overhaul manual...


(1) When installing the cylinder head bolts, check that the
shank length of each bolt meets the limit. If the limit is
exceeded, replace the bolt. - Limit: Max. 96.4 mm (3.79 in.)
(2) Install the washers.
(3) Apply engine oil to the bolt threads and washers.
(4) According to the tightening sequence, tighten the bolts to
75 Nm (54 ft.lbs.).
(5) Loosen the bolts completely.
(6) Torque the bolts to 20 Nm (14.5 -ft.lbs.)
(7) Tighten the bolts l/4 turns (90”) more.
(8) Tighten the bolts l/4 turns (90”) additionally.

Posted on Feb 15, 2009

  • 136 Answers

SOURCE: my mitsubishi lancer 2005 model

Engine vibrate because of broken engine mounts. Loose belts. Brakes( during stops). Basics check them out

Posted on Oct 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mitsubishi lancer ck2 engine knock is coming when engine heat comes to normal level


I would need to hear this knock to try and guess what it is. sorry.

Sep 23, 2016 | 2000 Mitsubishi Lancer

1 Answer

How to replace the hood release cable for Mitsubishi lancer ck2 1998


If your not particular mechanically inclined, than do not attempt this.
You probably will not have the tools.
I would go to a friend who happens to have a LOT of mechanical tools and ask for help.
This is something that would be simple for someone good with their hands.

Jan 07, 2015 | 1998 Mitsubishi Lancer

1 Answer

How do i change to hood release cable on the ck2 lancer


Cut the handle end off, use gorilla tape to attach new cable to the old one, then very carefully pull it through the firewall.

Jan 07, 2015 | 1998 Mitsubishi Lancer

1 Answer

Lancer Ck2 N light indicator blinks while on drive when get to stuck on gear3


the blinking of a nuetral light usually means overheating of the trans fluid. it says to pull over an let it ( the fluid ) cool down..... hope that helps

Oct 16, 2014 | 2002 Mitsubishi Lancer

1 Answer

Whats the name of the 2004 lancer engine?


It is Charlie These numbers are to verify liter size 4 meaning number of cylinders g meaning gas engine 15 meaning 1.5 liters other letters are t meaning turbo charge. The cars VIN # number breaks it down for you and the dealer can tell you what engine you have.

Apr 28, 2014 | 2004 Mitsubishi Lancer

2 Answers

I have a 2000 lancer ck2 engine or 4G13 1.3, my problem is whenever i engage the airconditon the rpm falls rapidly, help please.


there's a regulator which adjusts the car rpm when ac is on
or it could be a vacuum hose check hoses

Jun 08, 2010 | 2002 Mitsubishi Lancer

Not finding what you are looking for?
2002 Mitsubishi Lancer Logo

510 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...