Question about 1999 Nissan Maxima

1 Answer

Location of a/t diagnosis communication line - 1999 Nissan Maxima

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 78 Answers

A/t and engine diag port are the same. It is the OBD II cable port. and is located under the dash on the drivers side. black or silver plug.

Posted on May 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

C0899 U1026 U1064 P0300 P0506 P0446


Best Manuals I don't know abut your model but i'm sure this lady here can help you

Oct 26, 2017 | Cars & Trucks

1 Answer

2006 gmc canyon will not go into 4 wheeldrive after 5 minutes of driving


The first place to start is have it checked for codes an to see if a scan tool will communicate with the 4X4 control module !
Diagnostic Starting Point - Transfer Case
Begin the system diagnosis with the Diagnostic System Check - Vehicle . The Diagnostic System Check will provide the following information:
?€¢
The identification of the control module or modules that command the system.


?€¢
The ability of the control module or modules to communicate through the serial data circuit.


?€¢
The identification of any stored diagnostic trouble codes (DTCs) and the status of the codes.

The use of the Diagnostic System Check - Vehicle will identify the correct procedure for diagnosing the system and where the procedure is located.
Install a scan tool.
Does the scan tool power up?
Go to Step 3
Go to Scan Tool Does Not Power Up

3

  1. Turn ON the ignition, with the engine OFF.
  2. Attempt to establish communication with all of the control modules on the vehicle. Refer to Scan Tool Does Not Communicate with Class 2 Device for the modules you should expect to observe.
Does the scan tool communicate with all of the expected vehicle control modules?
If you don't have a scan tool that will communicate with all modules on the vehicle or understand this , your best bet is to take it to a ASE certified repair shop or the dealer .

Jan 07, 2016 | 2006 GMC Canyon Crew

1 Answer

Is there a drain valve for a 2001 Olds Alero gas tank?


No however, you can unplug the fuel line from the injector rail and apply 12v power to the fuel pump diagnosis wire located on the drivers side fender and that will allow you to pump it out through the fuel line.

Sep 10, 2012 | Oldsmobile Cars & Trucks

2 Answers

Nissan sentra 4cyld


Hi, you have provided trouble codes p0100 AND p1605.


Trouble Code: P0100


Mass Airflow Sensor Circuit Malfunction
Possible Causes:



Air Intake leaks located after the MAF sensor assembly MAF sensor signal circuit is open, shorted to ground or power MAF sensor has failed PCM has failed


Trouble Code: P1605

A/T Diagnosis Communication Line Malfunction

Possible Causes:


TCM communication line circuit is open or shorted to ground TCM communication line circuit shorted to VREF or power (B+) TCM or PCM has failed TSB 01-004 (01/01) contains information related to this code
For the P0100, check the connector on top of the MAF sesnor for looseness or corrosion. Connector is on top in piocture below. jturcotte_361.jpg

Mar 25, 2011 | 2000 Nissan Sentra

1 Answer

I have a 1994 lincoln continental car. Hoe do I replace the suspention drier?


why do you want to replace it? As air is exhausted through it, it dires it out for the next use. it's part of compressor assembly.

1996 cont'l The air suspension system includes the following major components:
  • Air compressor to supply air to the air springs (part of front spring and shock and rear spring and shock absorber assemblies
  • Front spring and shock (3C098) and rear spring and shock absorber (5A965) at each corner of the vehicle
  • Four linear air suspension height sensors (5359): two rear and two front height sensors to maintain the vehicle at the proper ride height; only LH rear height sensor is used for air suspension.
  • Dual-mode front spring and shock and rear shock absorber assemblies with internal actuator.
All system functions are controlled by vehicle dynamics control module (5A919). This control module receives inputs from several different sources. These inputs include:
  • vehicle speed via multiplex communication network
  • ignition switch position
  • door position via multiplex communication network
  • height sensor position
  • air suspension service switch
  • engine rpm via multiplex communication network
  • ride and steering personality settings via multiplex communications network
Communications monitor system operation and allow diagnosis of any concerns that may develop in the system. System monitoring for the driver's use is provided through the instrument panel mounted message center indicator (10D898).
  • Diagnosis communication for the service technician is provided through the data link connector (14489) (DLC) under the instrument panel and Rotunda New Generation Star (NGS) Tester 007-00500 or equivalent.
The message center indicator will display AIR LEVELING DISABLED or CHECK RIDE CONTROL if the suspension system is not turned on or the vehicle dynamics control module detects a concern. If air leveling system disabled is displayed, check that air suspension service switch is in the ON position.
----------------------------------------------------------
Solenoid Valve Vent The vent solenoid valve operates as follows:
  • The vent solenoid valve allows air to escape from the system during venting corrections.
  • The valve is located in the air compressor cylinder head and shares a common electrical connector with the motor.
  • The valve is enclosed in the cylinder head casting, which forms an integral valve housing that allows the valve tip to enter the pressurized side of the system.
  • Air leakage past the valve tip is prevented by an O-ring seal.
  • The vent solenoid valve opens when a corner of the vehicle is high and the vehicle dynamics control module (5A919) determines lowering is required.
  • When the vent solenoid valve is opened, it provides an escape route for pressurized air.
  • However, the vehicle will not lower unless the air spring solenoid valves (5311) are also opened to allow air to leave the springs.
  • Lowering the vehicle corners requires the vehicle dynamics control module to open two solenoid valves, the vent and one air spring solenoid.
  • Air is exhausted from the spring and vents through the compressor air drier (5346).
---------------------------------------------------------------------------------------------
Section 04-05: Suspension, Computer Controlled 1996 Continental Workshop Manual
REMOVAL AND INSTALLATION Air Compressor and Drier Assembly Removal
  1. Turn air suspension service switch OFF.
  1. Disconnect electrical connector located on the air compressor.
  1. Disconnect two air lines from compressor air drier.
  1. Remove three fasteners retaining air compressor and drier assembly to radiator support, frame rail and fender apron.

Dec 22, 2009 | 1994 Lincoln Continental

1 Answer

I have a 2001 Ford Focus. The service engine light came on. The diagnosis was I need to repalce the EGR value. Where is it located and can I do this myself. Also how do you determine if it is a SOHC or...


Not sure what your diagnosis was but usually it is not the valve that goes bad. Its usually the DPFE sensor. Both these parts are easty to replace. The EGR valve looks like a flying saucer on top of the engine with a vacuum line going to it. Its most likely green line. The DPFE isnt far away from it. There are two lines going to it and an electrical connector.

Jul 15, 2009 | 2001 Ford Focus

1 Answer

05 Altima, car will not go when the accelerator is pressed


Have you had the battery and alternator checked yet? If not, you should. It may be that the control units connected to the CAN aren't being supplied the correct voltage(too low) to operate properly.

CAN COMMUNICATION
System Description
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle multiplex communication line with high data communication speed and excellent error detection ability. Many electronic control units are equipped onto a vehicle, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with 2 communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.

Component Parts and Harness Connector Location
1a3d150.jpg
1. ABS actuator and electric unit (control
unit) E125 (with ABS)
2. IPDM E/R E121
3. Display control unit M95 (with NAVI)
4. BCM M18 5. Combination meter M24
6. Data link connector M22
7. TCM F56 (with A/T) 8. ECM F54

Jan 10, 2009 | 2005 Nissan Altima

2 Answers

Hi... i'm new to the foreign car market...


1st check the #4 fuse (10A) and #10 fuse (7.5A) on the 'under-dash' fuse block.
then #9 fuse (10A) on the 'engine bay' fuse block.

if the fuses are good, the gauge assembly has has "self-diagnostic" feature.

Self-diagnostic Procedure

The gauge assembly has a self-diagnosis function.
. The beeper drive circuit check
. The indicator drive circuit check
. The LCD segments check
. The gauges drive circuit check (speedometer, tachometer, fuel gauge, coolant temperature gauge)
. The communication line check (the coolant temperature signal line between the gauge and ECM/PCM)


Entering the Self-diagnosis Function:
1. Push and hold the trip/reset button.
2. Turn the lighting switch ON.
3. Turn the ignition switch ON (ll).
4. Within 5 sec., turn the lighting switch OFF, then ON and OFF again.
5. Within 5 sec., release the trip/reset button, then push and release the button four times repeatedly.

NOTE:
. While in the self-diagnosis mode, the dash lights brightness controller operates normally.
. While in the self-diagnosis mode, the trip/reset button is used to start the beeper drive circuit test and the gauge drive circuit check.
. lf the vehicle speed exceeds 1.2 mph (2 km/h) or the ignition switch is turned OFF, the self-diagnosis mode ends.

The Beeper Drive Circuit Check:
When entering the self-diagnosis mode, the beeper sounds five times.

The Indicator Drive Circuit Check:
When entering the self-diagnosis mode. the indicators lights (such as: Seat belt indicator light, Door/hatch indicator light, Brake system light. Charging system light, Low fuel indicator light, maintenance required light) blink.

The LCD Segment Check:
When entering the self-diagnosis mode, the odo/trip segment blinks five times.

The Gauge Drive Circuit Check:
When entering the self-diagnosis mode, the speedometer, the tachometer, the fuel gauge, and the coolant
temperature gauge needles go from the minimum position to maximum position, then return to the minimum position.
NOTE:
After the beeper stops sounding and the gauge needles return to the minimum position, pushing the trip/reset button, starts the beeper drive circuit check {one beep), and the gauge drive circuit check again.
The check cannot be started until the gauge needles return to the minimum position.

The Communication Line Gheck:
In the seif-diagnosis mode, after the odo/trip LCD segments check, the self-diagnosis starts the communication line check.
lf all segments comes on, the communication line is OK.
lf the word" Error" is indicated, there is a malfunction in the communication line between the gauge assembly, the multiplex control unit, and the ECM/PCM,
f4a412b.jpgc169609.jpg
Ending the Self-diagnosis Function:
Turn the ignition switch OFF.

Note: lf the vehicle speed exceeds 1 .2 mph (2 km/h), the self-diagnosis function ends.
-----------------------

If everything works correctly during the check, check your VSS (vehicle speed sensor)



Aug 03, 2008 | 2004 Honda Accord

Not finding what you are looking for?
1999 Nissan Maxima Logo

Related Topics:

204 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...