Question about 1981 Ford F 100

1 Answer

Why would a Toyota truck spark plug wire catch on

My Toyota truck overheated with a hole in a hose. I lifted the hood and found a spark plug wire on fire and a heater hose on fire. The truck constantly over heats. Why?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 957 Answers

No circulation, stuck thermostat, pump, or collapsed hose.

Posted on May 13, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Toyota 4runner washer fluid does not come out


Open the hood and listen when some helper operated the "squirters".
You should hear a high-pitch whine that the washer pump makes.
No noise? Bad pump or bad wiring or corrosion at the terminals of the pump.
Noise heard?
Hoses are plugged up.OR the hose fell off the bottle and the bottle is empty.
You can use a small wire from a wire brush to un plug the squirt nozzles on the hood.Use pliers to feed the wire into the nozzles-you may poke your finger(sharp!).
Un plug the hoses that lead to the hood and apply air pressure to the hose from the windshield washer bottle.
Washer fluid is not toxic in small doses.

Feb 22, 2013 | Toyota 4Runner Cars & Trucks

Tip

Toyota Highlander_ How to change plugs


The Toyota Highlander is available in three different engine sizes: 2.4, 3.0 and 3.3 liter. The basic technique for replacing spark plugs is used for both engine sizes, but depending on the engine size you need to remove different parts from the Toyota Highlander to gain access to the spark plugs.
  1. 1 Pull the hood release and raise the hood on the Highlander. Allow the engine plenty of time to cool.
  2. 2 Remove some components to reach the spark plugs. On a 3.3 liter engine, unscrew and remove the V-bank cover and intake air tank. On a 2.4 and 3.0 liter engine, remove the number one engine cover.
  3. 3 Locate the ignition coils and spark plug wires that connect directly to the spark plugs or directly to the engine in the Toyota Highlander. In 2001 and 2002 models, theses are on the front and back of the engine. On models made after 2002, the spark plugs are along the sides. Grab the ignition coils or spark plug wires by the thick plastic piece at the end of the wire. Squeeze the end and turn it to release it from the spark plug. Pull back to remove the plug from the engine.
  4. 4 Slide the spark plug socket over the spark plug. The most common size of spark plug socket used on a Toyota Highlander is 16mm. Turn the socket to the left to unscrew and remove the spark plug from the cylinder well.
  5. 5 Apply a thin coat of anti-seize compound to the spark plug thread and into the wire boot to reduce the chance of sticking.
  6. 6 Insert the spark plug into the well and manually turn the plug into place. If you cannot reach the plug well manually, insert the plug into the socket and extension and use the extension to turn the plug into place. Do not use a socket wrench or flexible extension for this process because their force damages the spark plug.
  7. 7 Connect the ignition coil or spark plug wire to the spark plug. Turn to lock it into place.
  8. 8 Continue this process for the rest of the spark plugs. Replace any removed items onto the engine and lower the hood.



on Jan 26, 2011 | Toyota Highlander Cars & Trucks

1 Answer

What do you remove to have access to spark plugs


Tools you will need before you start1. 1/4" ratchet2. 1/4" extention3. 10 mm socket, 1/4" drive4. small flat bladed screwdriver5. 3/8" ratchet6. 3/8" long extention7. 5/8" spark plug socket, 3/8 " drive8. air compressor with blow gun or can of compressed air9. long needle nose pliers10. 1/4" internal diameter rubber hose 8 inches long11. wire coat hanger12. neverseez lubricantProcedure1. Remove the two 10 mm cap nuts on the top plastic housing over the engine2. Remove the two fasteners on the back of the housing and remove the plastic cover3. You will see four plastic blocks with four wire clips on each block. These blocks are individual coils for each sparkplug.4. Use compressed air to blow out debris around the blocks5. Use the small flat bladed screwdriver to carefully lift up on the tab that holds the electrical connector onto the block and slide the wire clip off the block.6. Remove the 10 mm bolt that holds the plastic block onto the engine. Use the needle pliers to firmly grasp the plastic screw and pull straight up to remove it
7. Loosen the 10 mm nut on end of the plastic rail that holds the wiring harness for the blocks so that the round plastic washer on the bottom of the block will not break when you pull off the block8. Carefully pull the plastic block out of the engine. There is a 4 inch tube attached to the block that extends into the engine to the spark plug. It will take some twisting and pulling but you must be careful not to catch the back part of the round plastic washer that you cannot see, on the bottom of the plastic wiring harness.9. The spark plug is at the bottom of the 4 inch hole.10. Blow compressed air down the hole to remove debris11. Use a 5/8 sparkplug socket with a rubber collar on the 3/8" extention to remove the spark plug. The rubber collar will hold onto the spark plug as it is removed.12. The NGK website recommends making sure the spark plugs have the correct gap .044 but the spark plug box says not to adust the gap because you might damage the needle point iridium tip. The new spark plug has a protective cardboard tube that is removed.13. Spark plugs can stick inside aluminum heads and break off when you try remove them, leaving only the threads of the plug inside the engine which will necessitate removing the head to remove broken spark plug. Putting neverseez on the threads of the new spark plug will prevent that in future spark plug changes14. Now comes an interesting choice. You can use the rubber tube over the neck of the spark plug to slowly drop it down the hole and hand tighten it or you can use the spark plug socket with the rubber collar. If you use the spark plug socket, the rubber collar will stick to the plug and you will pull off the extention, leaving the socket in the hole. A pair of long needlenose pliers will reach into the hole and remove the socket, but the rubber collar may remain on the plug and you will have to bend a piece of coathanger with a short 90 degree tip to reach into the hole and pull out the rubber collar. The rubber collar is there to prevent you from cocking a regular 5/8" deep socket at an angle which will break off the neck of the sparkplug, necessitating another 10 dollars and another trip to the auto parts store.15. After the spark plug is hand tight, give it 1/2 turn more.16. Replace the square block, being sure that the black silicone gasket on the bottom of the round plastic washer does not get bound up on the engine post where the 10 mm bolt goes. Tighten the bolt17. replace the electrical clip.18. Go to the next spark plug and repeat the procedure.19. After the last spark plug is done, be sure to retighten the 10 mm nut on the wiring harness rail20. Replace the plastic cover over the engine and you are done

Nov 09, 2011 | Toyota Cars & Trucks

1 Answer

I can't find the spark plugs on my 2006 Toyota Solara. Could you tell me where they are located?


that vehicle does not have spark plug wires, you will see a coil for every cylinder, when you do is unplug the coil, remove the bolt holding it in and then lift it out, at the bottom of the hole is the spark plug.

Sep 25, 2011 | 2006 Toyota Solara

1 Answer

I would like to know how to locate the spark plugs on my celica GT.


They are between the cams. On top of the engine there are 4 wire bundles in the center of the valve/cam cover connecting to the spark coils. Undo the connectors and remove the single bolt for each one. Lift up the spark coil assemblies and find the spark plugs in the bottom of the hole underneath good luck.

Feb 19, 2011 | 2000 Toyota Celica

1 Answer

Anyone have picture/illustration of where the spark plug are located on a 2005 highlander?


  1. 1 Pull the hood release and raise the hood on the Highlander. Allow the engine plenty of time to cool.
  2. 2 Remove some components to reach the spark plugs. On a 3.3 liter engine, unscrew and remove the V-bank cover and intake air tank. On a 2.4 and 3.0 liter engine, remove the number one engine cover.
  3. 3 Locate the ignition coils and spark plug wires that connect directly to the spark plugs or directly to the engine in the Toyota Highlander. In 2001 and 2002 models, theses are on the front and back of the engine. On models made after 2002, the spark plugs are along the sides. Grab the ignition coils or spark plug wires by the thick plastic piece at the end of the wire. Squeeze the end and turn it to release it from the spark plug. Pull back to remove the plug from the engine.
  4. 4 Slide the spark plug socket over the spark plug. The most common size of spark plug socket used on a Toyota Highlander is 16mm. Turn the socket to the left to unscrew and remove the spark plug from the cylinder well.
  5. 5 Apply a thin coat of anti-seize compound to the spark plug thread and into the wire boot to reduce the chance of sticking.
  6. 6 Insert the spark plug into the well and manually turn the plug into place. If you cannot reach the plug well manually, insert the plug into the socket and extension and use the extension to turn the plug into place. Do not use a socket wrench or flexible extension for this process because their force damages the spark plug.
  7. 7 Connect the ignition coil or spark plug wire to the spark plug. Turn to lock it into place.
  8. 8 Continue this process for the rest of the spark plugs. Replace any removed items onto the engine and lower the hood.

Read more: How to Replace Spark Plugs in a Toyota Highlander ' eHow.com http://www.ehow.com/how_4484644_replace-spark-plugs-toyota-highlander.html#ixzz1C6Y4k5y2

Jan 26, 2011 | 2005 Toyota Highlander

1 Answer

Where are the spark plugs on a 2007 Toyota 4 cyl Camry. I removed the top cover and found holes with plastic liners which won't come out, but no spark plugs. Help needed.


Just follow the wires from the coil pack mounted on top, there are 4 of them, they will take you to the side of the motor where the spark plugs are hiding. Hope this helps.

Apr 27, 2010 | 2006 Toyota Corolla

1 Answer

I have a le is it a 4 our six celender


could be either, Lift hood....... count spark plugs/ wires

Feb 19, 2010 | 1994 Toyota Camry

1 Answer

Engine compartment got wet now it is missing and


Let a fan blow in the engine compartment for a long while. More importantly, the ignition wiring and plugs need to be dried out. Trace spark plug wires back to their source.Use WD 40 or a wire dry spray (auto parts store). Unplug spark plug wires and spray. Unplug ignition module wires and spray. Unplug all electrical plugs and spray. Also use a air dryer to remove moisture, and to dry out wires.

Jul 18, 2009 | 2002 Toyota Tacoma

1 Answer

Intermittent


Pull the spark plug wires out one by one and check for oil on wire. Sometimes the valve cover spark plug hole gaskets leak oil into the spark plug hole and causes a misfire. If oil found clean with brake or carb cleaner and blow out with compressed air. also when car runs bad listen under hood for snapping noise this would be spark escaping to ground somewere. In a dark garage you might be able to see the spark.

Feb 09, 2009 | 1995 Toyota 4Runner

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...