Question about 1992 Oldsmobile Cutlass Ciera

1 Answer

1992 cutlass supreme power steering line leaks

What is the easiest way to replace the high pressure power steering line on this car? I crawled under my Dad's cutlass and could barely see the hydraulic lines let alone reach them. What is the best way to get at them?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Oldsmobile Master
  • 14,036 Answers

You have to remove the driver side wheel and splash shield .its a very tight spot to get your arms and hands.if you got 3.1 engine remove the alternator .could help some.

Posted on May 13, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Why is oil in the breather hose?

Thats not oil more than likely its fuel and that would mean that the diaphram in the fuel pressure regulator is leaking.Pull the vacuum hose off the regulator and look for fuel if any runs out of it then replace the fuel pressure regulator.If regulator is leaking it will usally cause the engine idle high.

May 24, 2011 | 1992 Oldsmobile Cutlass Supreme

1 Answer

How Long to replace a power steering pressure hose? Labor cost?

6 cylinder engine remove and replace pressure power steering hose.

2.2 hrs X there shop labor rate = your labor cost.

Pre Mitchell labor guide

Jun 11, 2010 | 1992 Oldsmobile Cutlass Supreme

1 Answer

Power steering high pressure hose needs to be replaced on my 1991 oldsmobile cutlass supreme, 3.1L engine. However, I am unable to find repair guide.

The end going to power steering pump is easily accessible, however the end connected to the steering system is not as accessible. You will need an 18mm crows foot wrench and a long extension. Or since the line is being replaced anyway, cut the metal part of the hose as close to the nut that screws into the steering as possible so that you can use a deep-well socket on a two foot extension with a swivel. The steering mechanism is located approximately below your break booster and the high pressure line is the one closest to the fire wall.

May 30, 2010 | 1991 Oldsmobile Cutlass Supreme

1 Answer

My 92 cutlass supreme is spitting antifreeze e from water pump?

could be the upper hose best way to know it use a pressure test on the raidator

May 05, 2010 | 1992 Oldsmobile Cutlass Supreme

4 Answers

On a 1994 olds cutlass supreme SL can i put a regular rubber hose over a leak on the power steerings high pressure hose to buy myself time before i can afford to replace it? i plan on hose clamping it...

If it is a small leak you might be able to wrap it with a rubber hose and apply several clamps to put a band-aid on it. However, this is only temporary at best and could still cause problems depending on where it is leaking. One possible alternative to a new hose - if you take the hose to a shop like The Hoseman (or equivalent) they can rebuild the hose cheaper than buying a new one.

Jan 30, 2010 | 1994 Oldsmobile Cutlass Supreme

2 Answers

Power steering fluid leaking;

Fill it up. Have a helper hold the steering wheel to all the way to the stop while you check for leaks. Especially the high pressure hose.

May 04, 2009 | 1992 Buick Regal

1 Answer

My 1992 Cutlass Supreme SL Olds failed emissions.

High NOX readings indicate a somewhat lean condition IE: hot exhaust. Possible causes are cracked and leaking vacuum lines or lazy oxygen sensors. If possible have a reputable garage with engine electronics scanner services check the sensor to see if its helping to create the lean condition

Apr 25, 2009 | 1992 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
1992 Oldsmobile Cutlass Ciera Logo

192 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts


Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides