Question about 1999 Chevrolet Silverado 1500

1 Answer

Left rear tire drags in 4wd

When I shift the transfer case into 4 high or 4 low and the transmission is in drive or reverse it seems like the left rear tire drags, almost as if it wants to go in the other direction. I have a 1981 chevy 4x4 1/2 ton pick-up.

Posted by on

  • Anonymous Mar 28, 2014

    driving straight -no problem. When backing up left tiretoes in and right tire toes out real bad. I end up dragging wheels when in reverse . whats the problem and how do I Fix

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 453 Answers

Check the fluid in the the axle. Also make sure the brake isn't locking up. You might want to take the axle gear cover off and see if the "C" clip came off or is broken on the gear assembly. Almost sounds like the differentials is locking up.

Posted on May 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 ford ranger - Where is the 4x4 actuator located


On the transfer case
Transfer Case - Electronic Shift
The four-wheel drive electronic shift-on-the-fly feature electrically shifts the vehicle transfer case between 2WD, 4WD HIGH, and 4WD LOW. The system mode is selected by the operator through the mode select switch (MSS) on the instrument panel. The operator is informed which mode the system is in by two instrument cluster indicators: one for 4WD HIGH which appears as 4WD, and one for 4WD LOW, which appears as 4WD LOW. Shifts into 4WD HIGH can be made at any speed. When shifting into 4WD HIGH with the vehicle stationary, tooth blockage may occur preventing shift completion. When the vehicle is driven above 8 km/h (5 mph) the shift will complete. When shifting in or out of 4WD LOW, the four-wheel drive (4WD) control module requires that the vehicle speed be less than 5 km/h (3 mph), the brake pedal be applied, and the transmission be in NEUTRAL (automatic transmission) or the clutch pedal be depressed (manual transmission).
The gearmotor encoder assembly is mounted externally on the transfer case. It drives a rotary cam which moves the mode fork and range fork within the transfer case between the 4WD HIGH, 4WD LOW, and 2WD range positions.
The four-wheel drive (4WD) control module controls the gearmotor encoder assembly that shifts between 4WD HIGH, 4WD LOW, and 2WD modes.

Mar 17, 2017 | Ford Cars & Trucks

1 Answer

How do I repair the four wheel drive on a 1999 Ford Ranger XLT?


It depends on what is wrong , is the 4x4 light flashing ? Are you aware of the complexity of the 4x4 system ? Has a electronic control module , has the ability to set an store DTC'S - diagnostic trouble codes !
Transfer Case The four wheel drive system is an electronic shift 4X4 system that allows the operator to choose between three different modes. The operator can switch 4X4 HIGH modes at any speed. To engage or disengage 4X4 LOW the vehicle speed must be less than 5 kph (3 mph), the brake depressed, and the transmission must be in NEUTRAL.
The shift motor sense plate, an integral part of the electronic shift motor, informs the generic electronic module (GEM) of the transfer case shift motor and contact plates A, B, C and D position.
The digital transmission range (TR) sensor is located on the LH side of the transmission, and informs the GEM when the transmission is in the NEUTRAL position.
The electronic shift motor is mounted externally at the rear of the transfer case. It drives a rotary cam which moves the mode fork and range fork within the transfer case between the 4X4 HIGH, 4X4 LOW and 2WD range positions.
When the GEM verifies the completion of the transfer case shift from 2WD to 4X4 HIGH (reading the contact plate positions), the GEM will then energize both pulse vacuum hublock (PVH) solenoids (supplying ground for 45 seconds). The PVH solenoid will allow a HIGH flow of intake manifold vacuum to the "wheel end hublocks", engaging the wheel end hubs to the front differential and transfer case to achieve four wheel drive.
Here are just a few DTC'S the system can set an store in the module !
P1804 4WD High Indicator Circuit Failure GEM GO to Pinpoint Test C . P1806 4WD High Indicator Short to Battery GEM GO to Pinpoint Test C . P1808 4WD Low Indicator Circuit Failure GEM GO to Pinpoint Test C . P1810 4WD Low Indicator Short to Power GEM GO to Pinpoint Test C . P1812 4WD Mode Select Switch Circuit Failure GEM GO to Pinpoint Test A . P1815 4WD Mode Select Switch Circuit Short to Ground GEM GO to Pinpoint Test A . P1820 Transfer Case CW Shift Relay Circuit - Failure GEM GO to Pinpoint Test A . P1822 Transfer Case CW Shift Relay Coil Short to Power GEM GO to Pinpoint Test A . P1824 4WD Electric Clutch Relay Circuit Failure GEM GO to Pinpoint Test A . P1826 4WD Low Clutch Relay Short to Power GEM GO to Pinpoint Test A . P1828 Transfer Case CCW Shift Relay Coil Circuit Failure GEM GO to Pinpoint Test A . P1830 Transfer Case CCW Shift Relay Coil Short to Battery GEM GO to Pinpoint Test A . P1838 Transfer Case Shift Motor Circuit Failure GEM GO to Pinpoint Test A . P1846 Transfer Case CONTACT PLATE "A" Circuit Failure GEM GO to Pinpoint Test A . Now are you sure you really want to mess with this ? You would need a factory diagnostic scan tool to check this out before you start replacing parts !
Here

May 30, 2015 | Ford Ranger Cars & Trucks

1 Answer

How is four wheel drive used on a 1999 durango


Hi Ralph.

I do not own a Durango, but have owned many 4WD vehicles and can offer tips for proper usage.

The "L" and "H" after the 4 and 2 stand for "Low" and "High" ranges. The 2 and 4 stand for the number of wheels that can receive power from the engine and transmission. Most 4WD vehicles only provide power to 1 wheel on each axle (front at rear for a total of just 2 wheels powered) at any given time (but for purposes of discussion, we'll call it 2WD & 4WD, as advertised).

Generally, "2WD" is only offered as a High range and is the same as a "normal" 2WD car or truck. I haven't seen a car or small truck that offers 2L (but I haven't seen a Durango - so I don't know), but generally 2WD traction can be increased easily enough by simply shifting the transmission to a lower gear (From "D" to "2" or "2" to "1", etc.).

4WD is designed to provide additional traction whenever 2WD isn't sufficient. This can be when surfaces are slippery such as sand, mud, snow and ice or, when pulling a heavy load such as a trailer and tires are not gripping the surface well. Shifting from 2WD to 4WD High will provide more traction at the same tire speed. Maximum power from the engine does not come at low RPMs, so in order to get more pulling power from the engine with out increasing speed (or spinning tires), the transmission should shifted into a lower gear. This is especially helpful when pulling a trailer up a wet incline, etc. If 4WD High in 1st gear is still allowing tires to spin or not providing enough pulling power, then shifting the transfer case from 4WD High to 4WD Low will allow the engine speed to increase (providing more power) without increasing the speed of the wheels (reducing the chances of spinning tires).

4WD should never be used while operating on dry pavement. Since tires wear at different rates, and turning left or right slows the inside tire and speeds up the outside tire when compared to the rear tires, a certain amount of slip is required. Wet surfaces provide this necessary amount of slip - as does sand, mud, snow, ice, dirt, gravel, etc. You should take the time to see how each selection of High and Low affects engine speed and vehicle speed and how the surface and any trailer further changes traction. With a little experimentation, you'll see how it works and be able to choose the right range with little thought.

Don't forget to have the transfer case & front differential fluids checked and changed as per the manual. Neglecting this simple service intervals can leave you stranded when you need 4WD and can be very expensive to repair.

I hope this helps & good luck!

Aug 24, 2012 | 1999 Dodge Durango

1 Answer

4X4 ok on drive position but disengage in rear


Regarding 4 Wheel Drive problems,
Always follow Owners Manual for when and how to utilize 4 Wheel Drive. In most cases it should not be activated when vehicle is moving. Automatic Transmissions with 4 Wheel Drive have a Transfer Case similar to that used with Manual Transmissions. Shifting between LOW 4WD and HIGH 4WD should be selected while the vehicle is stopped. Again, follow Owners Manual Instructions. If you hear strange Grinding Noises have a Certified Technician check out your vehicle immediately.

Sorry that you are having troubles but, it sounds like the problem is more than a simple fix to me. If your Vehicle has Manual Locking Hubs make sure they are in the correct position for use in 4WD.

Dec 20, 2011 | Dodge Ram Cars & Trucks

1 Answer

How do I turn 4wd on?


    • 1 Start your Dodge truck's engine.
    • 2 Turn the electronic transfer case from "2WD" to "4WD Lock" to engage the high range 4WD, if the dodge truck is equipped with an electronic transfer case; otherwise, shift the transfer case lever from "2H" to "4H." The electronic transfer case is located on the instrument panel and is marked with "2WD," "4WD Lock" and 4WD Low." The lever-equipped transfer case is located to the right of your leg and is marked with "2H," "4H" and "4L."
    • 3 Shift the transmission into "Neutral" while the vehicle is either stopped or rolling at 2 to 3 mph to begin engaging in the low range 4WD. Turn the electronic transfer case to "4WD Low," if the Dodge truck is equipped with an electronic transfer case; otherwise, shift the transfer case lever from "2H" or "4H" to "4L."
    Tips & Warnings
    • Indicator lights will come on and alert you that your vehicle is in either the high or low range of 4WD.
    • Do not engage in the low range of 4WD drive if the transmission is in gear; you must shift to "Neutral" first.
    • Many Dodge trucks allow you to shift from 2-wheel drive to the high range of 4WD at up to 55 mph--consult your truck's manual to ensure that this is possible. Do not exceed 55 mph while engaged in the high range of 4WD. Do not exceed 25 mph while engaged in the low range of 4WD.
    • Do not engage in 4WD unless you are on slipper or rocky roads.

Sep 02, 2011 | 2005 Dodge Dakota

2 Answers

4wd does not work


Electronic Shift On the Fly (ESOF) Operation
The ESOF system is an electronic shift 4x4 system that allows the operator to choose between two different 4x4 modes as well as 2-wheel drive. The operator can switch between 2WD and 4WD HIGH mode at speed. To engage or disengage LOW Range, the vehicle speed must be less than 5 kph, the brake depressed, and the transmission must be in NEUTRAL.

The transfer case is equipped with an electromagnetic clutch which is located inside the case. This clutch is used to spin up the front drive-line when shifting from 2WD to 4x4 High mode at speed. When the control switch on the instrument panel is turned, the generic electronic module (GEM) recognizes that a shift has been requested and activates the electromagnetic clutch and the relays which power the transfer case shift motor. When the shift motor reaches the desired position as determined by the contact plate position inputs to the GEM, power to the shift relays and motors will be removed. When the transfer case front and rear output shafts are synchronized, the spring loaded lockup collar mechanically engages the main-shaft hub to the drive sprocket. Finally, the front axle collar is engaged and the electromagnetic clutch is deactivated.

Shift Between 2WD and 4x4 HIGH:
Shifts between 2WD and 4x4 HIGH can be made at speed. Listed below are the inputs and outputs needed by the GEM to execute a change between any of these modes.

Feature Inputs:
*4WD Mode Switch (Various resistances).
*Contact Plate Position Inputs A, B, C, D (grounded when closed, open circuit when open).

Feature Outputs:
*4x4 Shift Motor Relay Outputs
*Transfer Case Clutch Relay (grounded when relay is on, open circuit when relay is off).
*4x2/4x4 Vacuum Solenoid (grounded when activated, open circuit when deactivated).
*Cluster Indicators (ground when activated, open circuit when deactivated).

Shifting Into/Out of 4WD LOW:
When shifting into or out of 4WD LOW, the GEM requires that the vehicle speed be less than 5 kph, the brake is applied, and the transmission is in NEUTRAL.

Feature Inputs:
*4WD Mode Switch (Various resistances).
*Contact Plate Position Inputs A, B, C, D (grounded when closed, open circuit when open).
*VSS Sensor (Sinusoid Signal: 0.7V-20V, 2.2 Hz/mph).
Brake Input (battery voltage when brake is depress, open circuit when not activated).
*Transmission Range Sensor (grounded when transmission is in NEUTRAL, open circuit otherwise).
8Start/Clutch Depressed Input

Feature Outputs:
*4x4 Shift Motor Relay Outputs
*4x2/4x4 Vacuum Solenoid (grounded when activated, open circuit when deactivated).
*Cluster Indicators (grounded when activated, open circuit when deactivated).

4WD Mode Switch
A rotary switch allows the vehicle operator to choose between 2WD, 4WD HIGH, and 4WD LOW modes of 4x4 operation.

GEM Module
The Generic Electronic Module (GEM) controls the operation of the 4x4 system

Vehicle Speed Sensor
The vehicle speed sensor (VSS), mounted in the rear of the transfer case, informs the GEM of the vehicle speed.

Transfer Case Shift Motor Sense Plates

The shift motor sense plate, an integral part of the electric shift motor, informs the GEM to the positions of the transfer case

Transmission Range Sensor
Located on the left side of the transmission, this sensor informs the GEM when the transmission is in the NEUTRAL position.

Electric Shift Motor
The electric shift motor, mounted externally at the rear of the transfer case, drives a rotary cam which moves the mode fork and range fork within the transfer case to select between the 2WD, 4WD HIGH, and 4WD LOW positions.

4x4/4x2 Vacuum Solenoids
These two solenoids are attached to the upper RH side of the engine compartment dash, and alternately route vacuum to the vacuum motor which engages/disengages the center axle disconnect collar in the front axle assembly.

4x4 Shift Motor Relay
A module containing two relays which under the control of the GEM, shift the transfer case shift motor between the 2WD, 4WD HIGH, and 4WD LOW modes.

Transfer Case Clutch Relay
An electromechanical relay is used to activate the transfer case clutch within the transfer case.

Good luck and hope this helps,but start with the simple and check the fuses and wire harness. Both white/light blue stripe wires should have 12V in run. The GEM will ground the left side (closest to engine) solenoid to disengage the front axle. It will ground the the right side solenoid (closest to fender) to engage the front axle. If the GEM doesn't see Neutral it will not let the truck come out of 4Lo. If the GEM had water leaking on it it may well be the root of the problem. The shift motor only has power when the GEM sends it a signal to move the shift lever. Once the shift is completed the motor shuts off. There are 2 wires that control the shift motor. A yellow and an orange. The GEM alternates between 12v and Ground to these wires to control which way the motor turns. The GEM uses the transfer case shift relay module to control the power to the motor. There are contact plates inside the shift motor assembly that indicate the position that the shift lever is in. This is what the GEM used to know what the T-case is doing. Any one of these components can fail.







Jan 10, 2010 | 2002 Ford Explorer

1 Answer

1996 ford explorer 4wheel drive will not engage into the hubs need to know how it works


make sure your 4WD switch is working.and fuse is okay.because your 4WD is control by 4 electric shift motors in which drive a rotary cam which moves the mode fork and range fork inside the transfer case to select between 2WD HIGH A4WD - 4WD HIGH AND 4WD LOW RANGE.a shift motor sensing plate on the shift motor monitors the range in which the transfer case is operating a transmission range sensor monitors the gear position of the transmission.which must be in neutral to shift into low.a pair of solenoids one for 2WD one for 4WD.mounted on the upper right firewall route vacuum to the vacuum motor which engages and disengages the center axle disconnect collar in the front axle assembly.a 4 x 4 shift motor relay module contains two GEM controlled relays which shift the transfer case shift motor between 2WD and 4WD modes.a solid state clutch relay activates the A4WDclutch inside the transfer case.

Dec 13, 2009 | 1996 Ford Explorer

1 Answer

How to shift into 4wd


Ford has 2 types of 4x4 system engagement. One is a knob on the dash that you just turn to 4wheel drive high or low. The other system is the 4x4 transfer case shift on the transmission tunnel (hump) between the driver and passenger seats. To shift into 4 wheel drive high while driving, just let off the gas and shift transfer case into 4H position, and continue driving. To shift into 4 wheel drive Low, stop the vehicle completely, put transmission in neutral, shift transfer case into 4Low position, put trans. in gear, and start driving. I am assuming before doing the above, you have locked in ( turned the front hubs to 4 wheel drive position.) Any further questions, let me know.

May 16, 2009 | 2003 Ford F150 Regular Cab

1 Answer

Ford 2005 4x4 problem.


2-Speed Torque-On-Demand (TOD) Operation
The automatic 4-wheel drive (A4WD) system is a 2-speed torque-on-demand (TOD) operation that utilizes the following components:
  • Transfer case
  • 4-wheel drive (4WD) control module (integral to the powertrain control module [PCM])
  • Mode select switch (MSS)
  • Gearmotor encoder assembly (part of the transfer case shift motor)
  • Transfer case shift motor
  • Shift motor sense plate (part of the gearmotor encoder assembly)
Principles of Operation
Transfer Case Shift Motor The externally mounted transfer case shift motor, located at the rear of the transfer case, turns the shift cam assembly. As the shift cam assembly turns, it positions the reduction shift fork for desired transfer case operation. An integral position sensor in the shift motor provides shift motor position information to the 4WD control module.
Mode Select Switch (MSS) The push button MSS, mounted on the instrument panel, allows the operator to select the 4x4 Auto, 4x4 High, and 4x4 Low transfer case operating modes. The indicator light, on the instrument cluster push button, will illuminate only when the 4x4 Low position is engaged.
Visual Inspection Chart Mechanical Electrical
  • Axle shafts and CV joints
  • Driveshaft and universal joints
  • Fluid leaks
  • Matching tire sizes
  • Transfer case shift motor
  • Battery junction box (BJB) fuses:
    • 8 (30A)
    • 17 (5A)
    • 18 (20A)
  • Central junction box (CJB) fuses:
    • 12 (5A)
    • 24 (15A)
  • 4x4 module (PCM)
  • Wiring harness
  • Gearmotor encoder contact plate
  • Connector(s)
  • Circuitry
  • Mode indication switch (MSS)

  1. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
  1. If the concern is not visually evident, connect the diagnostic tool to the data link connector and select the vehicle to be tested from the diagnostic tool menu. If the diagnostic tool does not communicate with the vehicle:
    • check that the program card is correctly installed.
    • check the connections to the vehicle.
    • check the ignition switch position.
  1. If the diagnostic tool still does not communicate with the vehicle, refer to the diagnostic tool operating manual.
  1. Carry out the diagnostic tool data link test. If the diagnostic tool responds with:
    • CAN circuit fault; all electronic control units no response/not equipped, refer to Section 418-00 .
    • No response/not equipped for 4WD module (PCM), Go To Pinpoint Test G .
    • System passed, retrieve and record the continuous diagnostic trouble codes (DTCs), erase the continuous DTCs and carry out the 4WD module (PCM) self test.
  1. If the DTCs retrieved are related to the concern, go to the 4WD Control Module (PCM) Diagnostic Trouble Code (DTC) Index to continue diagnostics. 4WD Control Module (PCM) Diagnostic Trouble Code (DTC) Index
    DTC Description Source Action B1317 Battery Voltage HIGH 4WD Module (PCM) REFER to Section 414-00 . B1318 Battery Voltage LOW 4WD Module (PCM) REFER to Section 414-00 . B1319 Driver Door Ajar Circuit Failure 4WD Module (PCM) Go To Pinpoint Test M . B1322 Driver Door Ajar Circuit Short To Ground 4WD Module (PCM) Go To Pinpoint Test M . B1342 ECU is Defective 4WD Module (PCM) CLEAR the DTCs. REPEAT the 4x4 module (PCM) self test. If DTC B1342 is retrieved, INSTALL a new 4x4 module (PCM). REFER to Section 303-14 . CLEAR the DTCs. REPEAT the self test. B1483 Brake Pedal Input Circuit Failure 4WD Module (PCM) Go To Pinpoint Test M . B1485 Brake Pedal Input Short to Battery 4WD Module (PCM) Go To Pinpoint Test M . C1729 Transfer Case Unable to Transition Between 4H and 4L 4WD Module (PCM) Go To Pinpoint Test K . C1970 4WD Low Mode Switch LED Short to Battery 4WD Module (PCM) Go To Pinpoint Test K . C1971 4WD Low Mode Switch LED Circuit Failure 4WD Module (PCM) Go To Pinpoint Test K . P1707 Transfer Case NEUTRAL or PARK/NEUTRAL Indication Circuit 4WD Module (PCM) Go To Pinpoint Test M . P1812 Transmission 4-Wheel Drive Mode Select Circuit Failure 4WD Module (PCM) Go To Pinpoint Test K . P1815 Transmission 4-Wheel Drive Mode Select Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test K . P1816 Transmission NEUTRAL Safety Switch Circuit Failure 4WD Module (PCM) Go To Pinpoint Test M . P1819 Transmission NEUTRAL Safety Switch Circuit Short to Ground 4WD Module (PCM) Go To Pinpoint Test M . P1820 Transfer Case Clockwise Shift Relay Coil Circuit Failure 4WD Module (PCM) Go To Pinpoint Test K . P1822 Transfer Case Clockwise Shift Relay Coil Circuit Short To Battery 4WD Module (PCM) Go To Pinpoint Test K . P1824 4-Wheel Drive Clutch Relay Circuit Failure 4WD Module (PCM) Go To Pinpoint Test H . P1826 4-Wheel Drive Low Clutch Relay Short Circuit to Battery 4WD Module (PCM) Go To Pinpoint Test H . P1827 4-Wheel Drive Low Clutch Relay Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test H . P1828 Transfer Case Counterclockwise Shift Relay Coil Circuit Failure 4WD Module (PCM) Go To Pinpoint Test K . P1830 Transfer Case Counterclockwise Shift Relay Coil Circuit Short To Battery 4WD Module (PCM) Go To Pinpoint Test K . P1849 Transfer Case Contact Plate A Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test K . P1853 Transfer Case Contact Plate B Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test K . P1857 Transfer Case Contact Plate C Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test K . P1861 Transfer Case Contact Plate D Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test K . P1867 Transfer Case Contact Plate General Circuit Failure 4WD Module (PCM) Go To Pinpoint Test K . P1891 Transfer Case Contact Plate Ground Return Open Circuit 4WD Module (PCM) Go To Pinpoint Test K . U1900 CAN Communication BUS Fault 4WD Module (PCM) REFER to Section 418-00 . U2023 External Node Fault 4WD Module (PCM) REFER to Section 418-00 . U2051 One Or More Calibration Files Missing/Corrupt 4WD Module (PCM) Reprogram/Reflash the 4x4 module. REFER to Section 418-00 . - For All Other DTCs 4WD Module (PCM) REFER to Section 418-00 .
  2. Your best bet mite be to take it to a qualified repair shop !

May 30, 2017 | 2005 Ford Explorer

Not finding what you are looking for?
1999 Chevrolet Silverado 1500 Logo

289 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...