Question about 2004 Ford F150

2 Answers

How do you get the pass code for your exterior keypad

Posted by on


2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

If you remove the back seat and look for the Keyless wiring box and remove it. On the back side of it is the 5 digit factory default. Hope that was help full.

Posted on May 15, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert that has over 500 points.


    An expert whose answer got voted for 20 times.

  • Expert
  • 201 Answers

Hi susan p9,
you should be able to go to ford dealership and have them access the trucks vehicle identification number and either look -up your code or possible program in a new one.hope this helps..chris

Posted on May 13, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2004 Lincoln navigator interior lights don't come on when unlock. Sometimes auto headlights don't come on, seats don't move. Liftgate won't open until vehicle is started. Is this a relay or fuse?

. When you open the door or just unlock the door the lights don't come on ?
Vehicle Security Module The vehicle security module receives inputs from the following:
  • door ajar switches
  • keyless entry keypad
  • ignition switch
  • remote keyless entry transmitter
The vehicle security module uses these inputs to control an output signal to the instrument cluster which controls the battery saver relay and courtesy lamp output.
Interior Lighting Systems The instrument cluster grounds the battery saver relay and supplies the power for courtesy lamps when any door ajar switch is opened, or the interior lamp (headlamp) switch is closed. The instrument cluster then supplies voltage to the interior lamp circuit. Vehicle speed must be less than 24 kph (15 mph) for the instrument cluster module to keep courtesy lamps on. The interior lamps will remain illuminated for up to 25 seconds after all doors are closed unless the instrument cluster module receives an input from any of the following:
  • voltage from the ignition switch
  • a vehicle speed signal
  • input from the keyless entry keypad through the vehicle security module
  • input from the remote keyless entry transmitter lock or panic switch through the vehicle security module
Do you know what body control system DTC'S - diagnostic trouble codes are ?
Instrument Cluster Diagnostic Trouble Code Index DTC Description Source Action B1342 ECU is Defective Instrument Cluster REFER to Section 413-01 . B2499 Courtesy Lamp Output Failure Instrument Cluster Go To Pinpoint Test A . B1320 Driver Door Ajar Circuit Open Instrument Cluster Go To Pinpoint Test A . B1328 Passenger Door Ajar Circuit Open Instrument Cluster Go To Pinpoint Test A . - All Other DTCs Instrument Cluster REFER to Section 419-10 .
Principles of Operation
The autolamp system provides light-sensitive automatic on/off control of the headlamps and parking lamps controlled by the vehicle security module when the headlamp switch is in the autolamps position. When the ignition switch is turned to the RUN or START position with the autolamps feature already enabled and the ambient light level is dark, the vehicle security module will request the headlamps and parking lamps be turned on. When the autolamps are disabled, the vehicle security module will request the headlamps and parking lamps to be turned off, regardless of the ignition switch position. When the vehicle security module has turned on the exterior lamps and the ignition is turned to the OFF or ACCY position, the exterior lamps will remain on for an additional time specified by the customer or the headlamp switch is turned off.
When the autolamps have been enabled and the ignition switch is in the RUN/START position, the vehicle security module will request that the exterior lamps be turned on or off based on ambient light level. If the vehicle enters darkness for at least 15 seconds, the vehicle security module will request the exterior lamps on. If the vehicle enters light for at least 15 seconds, the vehicle security module will request the exterior lamps off. By delaying turning on and off the exterior lamps during short periods of darkness and light, the vehicle security module prevents the exterior lamps from flashing on and off.

  • The autolamps are inoperative - do not operate correctly
  • Circuitry.
  • Photocell.
  • Headlamp switch.
  • Vehicle security module.
  • Go To Pinpoint Test G .

Power Lock
The power lock/unlock feature requests all of the vehicle doors, including the liftgate, be locked or unlocked upon a customer request from any interior door lock switch in the vehicle. The power door locking system functions independently of ignition status or vehicle speed. When the vehicle security module receives an unlock/lock command from any door lock control switch, the vehicle security module will activate relays internal to the module to supply the correct power and grounds for the door lock actuators.
Your best bet , take it to a qualified repair shop .

Feb 25, 2018 | Lincoln Cars & Trucks

1 Answer

How can i get ezpass for out side the car over the license plate,because i can't put inside the car there is a big box with lots of monitoring system on the windshield

Hello, Johnson -

Despite other equipment on the interior windshield of your vehicle, you still don't want to put an E-Z Pass transponder on the exterior of the vehicle. On the exterior of the vehicle it will be easy for someone to steal.

I believe the E-Z Pass transponder is supposed to be placed in the upper part of the interior windshield on the driver's side.

Best wishes.


Feb 12, 2018 | Cars & Trucks

1 Answer

What is code p0496

Evap Emission High Purge Flow Fault. This means that the carbon cannister under the hood that collects fuel tank vapors is no longer operating. You won't pass smog until it's fixed.

Jun 30, 2014 | 2007 GMC Envoy Denali

1 Answer

2008 Lincoln Town Car lost permanent pass code for keypad

The makers hide the code on a sticker in an inconspicuous place. They used to put it on a hinge in the trunk, the hood, or inside the doorjam cavity. You would need the original Code anyway to change to a new chosen one.

Finding this for you is a small service for a Dealer to provide. Your Lincoln is also about 5 years old and has a longer Warranty, but this is a small favor to do for a customer. Ask them if they can find it or if it is linked to your Vin#.

Dec 01, 2013 | 2008 Lincoln Town Car

2 Answers

How can i get the keypad code to unlock my 2005 ford explorer?

The factory keypad code is the bold numbers listed on the side of the keypad module, should be located under the drivers side dash on the left, look for the numbers that are in bold type. Hope this helps, let me know

Dec 14, 2009 | 2005 Ford Explorer Sport Trac

1 Answer

I just bought a 2002 explorer and it has a keypad entry system. There are no books with it. How do I find the code or enter a new code.


To erase any personal code set by the prior owner, use these steps:
1. Use the keypad to enter the factory set code.
2. Within five seconds, press the 7/8 and 9/0 buttons simultaneously.
3. The system will now respond only to the factory set code.

You can program your own personal code via these steps:
1. Use the keypad to enter the factory set code.
2. Within five seconds, press the 1/2 button
3. Within five seconds, begin entering your personal five digit code.
(Each subsequent keypress must be within five seconds of the previous)
4. The system will now respond to both your new personal code and the factory set code.
5. Put the factory set code you wrote down in a safe place. It will always open your door, and it won't do you any good if locked inside your vehicle.

Hope this help

Sep 24, 2009 | 2002 Ford Explorer

1 Answer

94 crown vic how do i find out if car has keyless entry

Easy. Does your Vic have a five number keypad above the driver's side exterior door handle? If so the you got key-less. If not, you do not.

Jun 13, 2009 | 1994 Ford Crown Victoria

1 Answer

Replacing passenger side miror

need to replace the exterior mirror on the passenger side. How do I remove the mirror from the out side. all the wiring is out Just need advice on how to take of the existing mirrow and replace it with a new one. Does the inside panel need to come off, how many bolts are needed for removal.


Dec 29, 2008 | 2007 Chevrolet Tahoe

1 Answer

Reprograming my exterior key pad???

Up under the dashboard to the left of the steering column is the anti-theft module. It is a square box about 4"X4" and should be tan in color. On the cover, there is a sticker with a 5 digit code. This is the keypad code.

May 26, 2008 | 2000 Ford F150 Flareside SuperCab

Not finding what you are looking for?
2004 Ford F150 Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

80407 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides