Question about 1988 Dodge Aries

2 Answers

Codes my 88 dodge is spitting out engine codes 1-2 1-3 5-5 can anyone help?

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 38 Answers

I find no listing for a code 12.
code 13 is due to a "canister purge solenoid circuit" problem
and the code 55 just signals that the message is over. i hope this helps

Posted on May 12, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

After the battery has been disconnected code 12 will appear until after 15 starts. If it persists then the battery is not keeping a charge properly and needs replaced

code 55 = end of file

cite: http://www.allpar.com/fix/codes/index.html

Posted on May 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 2004 Dodge Dakota. Runs great until it accelerates to about 4k rpms and then the motor spits an sputters. Anyone ever have this problem or know what might cause this? Would appreciate any advice!


Need more information. Is there a check engine light on? First thing I would check is the coil but you should have a check engine light on if that's the problem. Get the codes and it will help you alot on fixing your problem.

Sep 29, 2013 | 2004 Dodge Dakota

1 Answer

88 dodge conquest tsi no start has spark has fuel to the injectors but i dont think its pulsating the injectors fuel up to the injectors but not spitting fuel


you can disconnect 1 of the wiring connectors to the fuel injectors one at a time, and hook up a noid light into the wiring connector, and then turn ignition on, and watch for the noid light to flicker, this will show you that there is electricity going to the fuel injector, if this all checks out, then you can also use a mechanics stethoscope , and place the probe onto each fuel injector with the wiring connected, and then crank the engine, to see if you hear a clicking noise coming from the injectors, the injector that has liitle or no sound is the bad one.

Apr 03, 2011 | 1985 Dodge Conquest

1 Answer

Spitting and sputtering dose not go over 20 mph no codes in computer check engine lite goes on and off computer says every thing operating fine according to code book need it fix any suggestions


If your check engine light is going on and off this usually indicates a misfire condition there should be codes inside your computer for the misfire circuit usually it would be PO300 for mulitiple cylinder misfire P0301 would be cylinder 1 and so forth recheck your computer for codes because with a misfire it will definatly set a hard code....

Dec 06, 2010 | 2002 Dodge Neon

1 Answer

I need a radiator. is there any radiators that will inter change


1989 Dodge Omni Radiator

Part Number: 12553SAP0882P
Manufacturer Part Number: w5LDkcOWw5bDkMK7w5PDm8Obw5HCsw==

Part Specifications:
Core Size (in) approx: CU/BR 17-1/4 x 12-1/2 x 1-1/4, 2 ROW
Tank: PLASTIC
Weight: 8

Part Details
2.2L L4 Without Heavy Duty Cooling + Without AC - All Transmission.



This Part Fits:
1983-83 : DODGE OMNI 1.6L L4 98
1984-88 : DODGE OMNI 1.6L L4 98
1984-88 : DODGE OMNI 2.2L L4 135
1989-89 : DODGE OMNI 2.2L L4 135
HOPE IT HELPS

If this helps you resolve your problem, please consider giving a good rating and a quick thanks or good job.It will help me as well Thank you.

Oct 25, 2010 | 1989 Dodge Omni

1 Answer

Check engine light is on and it is idling rough


The code 22 is the ect sensor voltage to low( engine coolant temperature sensor input below minimum acceptable voltage) Code 27 injector #4 control circuit ( injector #4 output driver does not respond properly to control signal). Code 43 ignition coil #3 primary circuit (peak primary circuit current not achieved with maximum dwell time. And code 55 completion of fault code display on check engine lamp. Hope this will help you.

May 29, 2010 | 1996 Dodge Caravan

1 Answer

Engine problems


If my codes are correct 12 is battery disconnected...likely because it was while doing job, 37 is converter clutch malfunction...Don't see a connection between those and your problem, unless a harness is pinched or disconnected. Have the shop that did the work take a look at it first...If they are reputable they will be concerned.

Aug 02, 2009 | 1994 Dodge Ram

2 Answers

Fault code 88 dodge dakota


Replace the mass air flow meter.

Aug 01, 2009 | 2002 Dodge Dakota Club Cab

1 Answer

Engine stalling


Hello doncoth...very low mileage for an 88 aries and i doubt that anything serious is going on.
In 88 these engines were carbureted, not fuel injected & majority of the stalling problems were fuel system related on these cars,
like a broken or split vacuum hoses allowing air to be sucked into the intake manifold. Unmetered air changes the fuel mixture, and can cause a stalling problem..
Since the check engine light is coming on we need to find out what the trouble codes are.
To get the codes, put the key in the ignition and turn the key to the "run" position until all the dash lights come on (DO NOT START) Have your paper and pen ready to take notes.
Turn key back "off",then to "run" again,"off" again and then back to "run " and leave it there.....The check engine light will begin flashing....It will flash a 2 digit code....For instance,2 blinks followed by a pause,then 1 more blink would be code "21"....The last code displayed will be 55 (test is over) From that information we can determine the cause of the condition. The codes can be read here>>>> http://www.allpar.com/fix/codes/index.html the list is at the bottom of the page. Let me know what you find. I'll be glad to help you.
Good luck and i hope this helps.

May 23, 2009 | 1988 Dodge Aries

1 Answer

Codes for 1988 dodge aries


The codes can be pulled from this car by turning the key to off on off on off on then on the forth time leave the key in the on position and observe the check engine light it will blink in two number codes for example 3 blinks then a pause and 2 more blinks would mean code #32. Here is a link to the codes table:

http://www.troublecodes.net/chrysler/95_25sfi.shtml

These codes for a 95 2.5 should be the same for your 88.

Sincerely,

JC

Nov 12, 2008 | 1988 Dodge Aries

2 Answers

96 dodge grand caravan help me please


Check MAP sensor. If PCM gets wrong data from MAP sensor it should offset ignition timing and/or make fuel mixture too lean or too rich.

Nov 05, 2008 | 1996 Dodge Grand Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

246 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...