Question about 1993 Mazda Protege

1 Answer

I have a 1999 mazda 626. a/c works with blower on 1-3 but doesn`t blow, blower works on 4 but a/c goes off ? blower on its own only works on 4 ?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,392 Answers

Needs a blower motor resistor.

Posted on May 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Code p0141, bank 1 sensor 2 heater circuit. Where is this sensor located on a 1999 mazda 626 automatic 4 cylinder.


starting at the tail pipe go towards the engine and the first one you come to is sensor 2. Replace it period.

Oct 06, 2016 | 1999 Mazda 626

2 Answers

If air conditioner system not working cause 1999 Mazda 626 2.0L to overheat


No this wont cause an overheat problem. Check the coolant level , check to see if the fans come on after it heats up. when the car is warming up you can check the thermostat, by touching the top radiator hose, after a few minutes the hose should get hot, this indicates that the thermostat opened up and is working. If it doesn't replace the thermostat. If it doesn't over heat until you start driving , then suspect the water pump. The impellers can slip on the shaft and not have enough flow to keep it cool.

Aug 26, 2011 | 1999 Mazda 626

1 Answer

Heater has stopped working


(1) possible blown fuse.
Note that fuses blow for a reason - seek out the reason, or it will blow its new fuse too.

The main fuse block is located inside the left side of the engine compartment near the battery. There is also an interior fuse panel located just above the left side kick panel.

Interior Fuse Panel
The interior fuses simply unplug from the fuse panel. Use the fuse puller tool provided with your car to remove fuses from the panel. The tool is located on the back of the interior fuse panel cover.


(2) possible blower motor dead. See maintenance manual excerpt below.

(3) possible blower motor relay faulty. Location of Blower relay:
Under hood, drivers side, front engine area,rear of headlight housing; relay mounted on drivers side of radiator shroud.


1990-92 Mazda 626 and MX-6
See Figure below

archaeology_8.jpg
  1. Disconnect the negative battery cable.
  2. Remove the glove box and the underdash cover.
  3. Detach the electrical connectors from the blower unit.
  4. Remove the blower unit-to-fire wall attaching bolts and remove the blower unit assembly.
  5. Remove the blower motor fan-to-motor fastener.
  6. Remove the blower motor-to-unit attaching bolts, then remove the motor.
  7. Installation is the reverse of the removal procedure.

Feb 01, 2011 | 1991 Mazda 626

1 Answer

Fan only works on 4 in my mazda 323f bj modle


this problem is caused by the fan speed control resistor, it is located next to the blower motor in the heater duct work.

Feb 23, 2010 | 1999 Mazda 626

1 Answer

Spark plugs wires order on mazda 626 V6 1997


1 3 5
2 4 6
(Front of engine)
The distributor has the #1 cylinder's wire marked. The rotation is counter-clockwise and goes: 1-2-3-5-4-6

i hope this helps
-matthew

Oct 28, 2009 | 1997 Mazda 626

1 Answer

1991 Mazda 626, the heater/ac/blower isn't working. the controls don't put anything out. the engine does rev up when blower is engaged, but it doesn't blow? what could be possible problems?


The problem is with the Blower regulator. It is a voltage divider to control the blower speed. when it is bad, it causes the circuit open, not deliver a current to the blower, so blower is not working.

Oct 28, 2009 | 1991 Mazda 626

Not finding what you are looking for?
1993 Mazda Protege Logo

Related Topics:

355 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...