An expert who has achieved level 3 by getting 1000 points
An expert that got 10 achievements.
An expert that got 5 achievements.
An expert whose answer got voted for 100 times.
Re: Looking for cambelt timing marks/ positions please, ...
These bend valves if belt breaks while running
Align the timing marks on the camshaft gears to the notches on the camshaft cover, using the intake gear mark for the intake gear and the exhaust gear mark for the exhaust gear.
Align the mark on the crankshaft gear with the
notch at the bottom of the rear timing belt cover.
Re: Looking for cambelt timing marks/ positions please, ...
Search you tube for daewoo timing belt. on the right on other option it shows a suzuki which is identicle engine and set up. if your belt broke you have no choice but to replace the head also. i am on mine now...wish me luck
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need. Goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Hi, I have pasted instructions below from autozone.com. The instructions call for the use of special tools. You can improvise with alternate tools, but please make sure your timing is right before closing the cover. Please let me know if you have questions, and thanks for using FixYa.
1.9L Diesel Engine Some special tools are required to
perform this procedure properly. A flat bar, VW tool 2065A is used to
secure the camshaft in position. A pin, VW tool 2064 is used to fix the
pump position while the timing belt is removed. The camshaft and pump
work against spring pressure and will move out of position when the
timing belt is removed. It is not difficult to find substitutes but do
not remove the timing belt without these tools.
Do not turn the engine or camshaft with the timing belt removed.
The pistons will contact the valves and cause internal engine damage.
Disconnect the negative battery cable and remove the accessory
drive belts, crankshaft pulley and the timing belt cover(s). Remove the
camshaft cover and rubber plug at the back end of the camshaft.
Temporarily reinstall the crankshaft pulley bolt and turn the
crankshaft to Top Dead Center (TDC) of No. 1 piston. The mark on the
camshaft sprocket should be aligned with the mark on the inner timing
belt cover or the edge of the cylinder head.
With the engine at TDC, insert the bar into the slot at the back
of the camshaft. The bar rests on the cylinder head to will hold the
camshaft in position.
Insert the pin into the injection pump drive sprocket to hold the pump in position.
Loosen the locknut on the tensioner pulley and turn the tensioner
counterclockwise to relieve the tension on the timing belt. Slide the
timing belt from the sprockets.
Fig. Use the VW tool to lock the camshaft at TDC for timing belt replacement-Volkswagen 1.9L Diesel engines
Fig. Locking the injection pump with the VW tool as shown-Volkswagen 1.9L Diesel engines
Install the new timing belt and adjust the tension so the belt can
be twisted 45 degrees at the halfway point between the camshaft and
pump sprockets. Tighten the tensioner nut to 33 ft. lbs. (45 Nm).
Remove the holding tools.
Turn the engine 2 full revolutions to return to TDC for the No. 1
cylinder. Recheck belt tension and timing mark alignment, readjust as
Install the belt cover and accessory drive belts.
If the belt is too tight, there will be a growling noise that rises and falls with engine speed.
hi from uk the cambelt timing marks at TDC are as follows--the crank gear mark is lined up with mark on front of engineblock at approx 10-30 am position the marks are clear as you look ? the cam coghas a dot/pop mark just below teeth this mark is at top ie 12-0'clock position now on cam cog you will also see s hole drilledon the cog web also at 12-o/clock if you look thro this hole (use a mirror ?) the hole lines up to a grooved vertical line at the rear which is on front of engine at this point you fit belt fron crank pully anti clockwise round cam cig then reset tensioner when marks are rechecked with belt fitted/tensioned ? turn engine manually two full rotations clockwise then recheck all mark line up again ? then re assemble ? c/shaft pully bolt tightens to=170-180 Nm hope you notice that the new belt is marked as to its rotation with arrows hope this helps ?best wishes from uk
the cambelt timing marks for clio 1.4 are = the crankshaft cog alignes withmark at 6 o/clock position at TDC No 1 cyl and the cam cog alignes with mark on cyl head at rear of cog at 12 o/clock position belt is fitted anti clockwise from crank then w/pump and then cam cog hope this helps ?
put number one cyl to tdc take out plug put long screwdriver down to check this if you are not sure /check marks on cam pulleys are correct at this point you need to use locking tool to hold pulleys still .if used before you would not have had a problem re fit belt tension turn over 2 times re check marks re check belt tension should be ok now unless valve has got bent moral always lock the camshafs on twin cam engines
hi from uk the cambelt timing marks you req are as follows the crank cog has a dot indent on it and it has to align with same mark on the engine front at approx 12-30 pm position? it is clearly visible then the cam cog you will see a small drilled hole on the cog between the outer toothed and the centre securing bolt ? this hole in cog has to be positioned at top 12 o'clock position then look through this hole and you will see it lines up with a V indent on cyl head this too is clearly visible and advise setting this up b4 fitting c/head for ease ? with these marks set up the engine is at T D C number 1 firing just a note! if you arefitting new belt? it is advisable to replace the tensioner too ! as a kit here in uk belt+tensioner costs £50 if you wish? i can scan and e mail full instructions on cambelt+tensioner strip+renewal proceedure plus detailed diagram of belt set up and relevent marks and tensioner proceedure if you send an e mail address best wishes from n/west uk