Question about 2003 GMC Sierra

1 Answer

Tps I need to know what that is mean ? (p2135 -Accelerator pedal position potentiometer circut incorrect comparison between both tracks.) please .

Posted by on

  • ama_aboali May 12, 2009

    I change the TPS & PCM & ECM , When I click on the throttle, engine speed does not increase what can do please?

    Best wishes

  • ama_aboali May 13, 2009

    dear sir

    I change the TPS on the throttle body and the accelerator

    pedal inside.and ECM. and When I click on the throttle, engine speed does not increase what can do? please.


    Regards,

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GMC Master
  • 1,000 Answers

Your truck has an electronically controlled throttle system. There are (2) TPS sensors located on the accelerator pedal.
Both of the sensors must agree, by way of a voltage signal, to the current position of the throttle. If (1) of the sensors sends a different voltage signal back to the PCM than the other, the PCM will set this fault.
The reason for the (2) sensors is redundancy. In the event a sensor fails, the other will allow the engine to run and not leave you stranded.
A scan tool will be able to determine which sensor is out of sync and then can be replaced.
I hope this satisfies your question. Let me know.
Regards,

Posted on May 12, 2009

  • Bruce Bracey
    Bruce Bracey May 13, 2009

    Did you change the TPS on the throttle body or the accelerator pedal inside.

    Regards,

  • Bruce Bracey
    Bruce Bracey May 14, 2009

    You will need to take it to your favorite vehicle technician who has a vehicle scanner. He will then look at the signal input from the accelerator pedal an see if he is receiving anything to the PCM. Also, he will be able to function the throttle with the scan tool to insure the circuit is correct and perform a PCM reset.

    The only other way would be to pin each wire out with a volt/ohm meter.

    Do you still have the old PCM?

    Good luck, let me know.

    Regards,

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to know the code po120


Throttle Position Sensor/Switch (TPS) A Circuit Malfunction
The TPS (Throttle Position Sensor) is a potentiometer that is mounted to the throttle body. It detects the throttle blade angle. As the throttle blade moves, the TPS sends a signal to the PCM (Powertrain Control Module). Usually a three wire sensor: A 5 volt reference from the PCM to the TPS, a ground from the PCM to the TPS, and a signal return from the TPS to the PCM. The TPS sends the throttle position information back to the PCM on this signal wire. When the throttle is closed the signal is near .45 volts. At WOT (Wide Open Throttle) the TPS signal voltage will approach a full 5 volts. When the PCM sees a voltage that is outside of normal operating range, P0120 will set. NOTE: The PCM knows that any large change in throttle position means a cooresponding change in manifold pressure (MAP). On some models the PCM will monitor MAP and TPS operation for comparison. Meaning that if the PCM sees a large percentage change in throttle position, it expects to see a cooresponding change in manifold pressure and vice versa. If it doesn't see this comparitive change, P0120 may set.

Dec 11, 2014 | 2001 Toyota Sienna

2 Answers

P2135 07 Suzuki swift


fly by wire.
Throttle body failure, clean it and pray.
bad TPS wires at same place.
- Faulty electric throttle control actuator (TP sensor 1 and 2)
- Throttle Position Sensor harness is open or shorted
- Throttle Position Sensor circuit poor connection
- Faulty accelerator pedal position sensor
http://helpforcars.net/obd_codes/p2135_suzuki.html

Oct 15, 2013 | Suzuki Cars & Trucks

3 Answers

Accelerator pedal position sensors


I have a 2006 Honda Accord and I put it on the dealers diagnostic system and it gave the following reading: Acclerator pedal position interrelationship. Does this mean that the throttle body cencor and the accelerator pedal position cencor needs to be syncronized to find each other? Please help

Oct 09, 2013 | Honda Accord Cars & Trucks

1 Answer

Check engine light sensor


DTC P2138: Accelerator Pedal Position (APP) Sensor A/B (Throttle Position Sensor D/E) Incorrect Voltage Correlation.

Accelerator pedal position (APP) sensor A and accelerator pedal position (APP) sensor B are potentiometers, and they are installed in the engine compartment.

The APP sensors A and B are operated via the throttle cable to determine the accelerator opening value when the driver presses the accelerator pedal. The accelerator pedal opening value is converted to a signal in APP sensors A and B and transmitted to the engine control module (ECM)/powertrain control module (PCM) to compute the target position. The target position signal is then transmitted to the throttle actuator control module.

APP sensor A is for the primary control, and APP sensor B is a back-up of APP sensor A in case it malfunctions. Both sensors compare their output voltage to each other for malfunction detection.

When the voltage difference of APP sensor B is out of a fixed range for a set period of time, the ECM/PCM detects a malfunction, and a DTC is stored.

Sep 15, 2013 | 2007 Honda Accord Sedan

2 Answers

Trying to purchase used mercury mountaineer but shows a code of P2135what does that mean and is it expensive to fix? please advise


You may want to check with the dealer or do some internet research on the code - - the generic code means there is a problem with the throttle position switch circuit. It could be different for a Mercury product.

Oct 09, 2012 | 2004 Mercury Mountaineer

3 Answers

Can anyone tell me what does the following codes mean for my 2006 Ford F-150 Pick up 4.6 litre The codes are as follows: P210406, P2111, P2112, and P2135.


code p2111 throttle actuator control system actuator stuck open. throttle actuator control system circuit malfunction. brake vacuum implausible signal. code p2112 throttle actuator control system actuator stuck closed.throttle actuator control system circuit malfunction. code p2135 accelerator pedal position sensor switch a b voltage correlation. throttle position sensor switch a b voltage correlation. electronic throttle position sensor switch 1 implausible signal. did not see code p210406 that code too long.

Apr 15, 2011 | Ford F-150 Cars & Trucks

3 Answers

Eng light code po441 and po122


Code P0441 is the purge solenoid. Examine the fuel system to make sure none of the vapor hoses are cracked or leaking. If the hoses and all connections are as they should be you'll need to replace that purge solenoid.

P0122 is the APPS sensor: The Accelerator Pedal Position Sensor (APPS) is a linear potentiometer. It provides the Engine Control Module (ECM) with a DC voltage signal proportional to the angle, or position of the accelerator pedal. This used to be referred to as the Throttle Position Sensor (TPS). You'll need to check the connections at the sensor and most likely replace.

Nov 14, 2009 | 2004 Dodge Dakota

2 Answers

Pedal position malfunction


You can change the tps alone. You do not have to change the entire throttle body. It shouldn't be riveted in place, it should have screws or bolts on one side or the other. If it's riveted in place, use a dremmel and grind the rivets off. You can replace rivets with screws on the new unit.

May 24, 2009 | 2003 GMC Sierra

Not finding what you are looking for?
2003 GMC Sierra Logo

259 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...