Question about 1994 GMC Jimmy

1 Answer

Cadge cluster 1994 GMC Jimmy the spedomter is not working i cant tell what speed I'm on the cadge is digtel its in same aria with the turn signals

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Call junkyards for a new 1. had the same prob n had to b replaced

Posted on Sep 18, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

A 2001 jimmy gmc my speedometer dose not work and my transmision will not shift i changed the sensor and it didnt fix the problem i changed the filter didnt help what else could cause this problem

What sensor did you change . VSS - vehicle speed sensor or output speed sensor .
The ideal what to find the problem would be to hook up a factory scan tool to see the VSS is put out a signal to the PCM/ECM , then see if the PCM /ECM is sending info to the instrument cluster ,. And knowing how these this work couldn't hurt either .

The IPC displays the vehicle speed based on the information from the PCM. The PCM converts the data from the vehicle speed sensor to a 4000 pulses/mile signal. The IPC uses the vehicle speed signal circuit from the PCM in order to calculate the vehicle speed. The speedometer defaults to 0 km/h (0 mph) if a malfunction in the vehicle speed signal circuit exists.

Have the vehicle checked for DTC"S - diagnostic trouble codes . No all code's turn on the check engine light .
DTC P0608
The PCM creates the vehicle speed output signal by pulsing the circuit to ground. The PCM pulses the circuit at the same rate as the vehicle speed signal input. The PCM monitors the voltage on the vehicle speed signal circuit. If the PCM determines the voltage is out of the normal operating range, a DTC sets.

Install a scan tool.
Raise the vehicle's drive wheels. Refer to Lifting and Jacking the Vehicle in General Information.
Start the engine.
Place the transmission into drive for an automatic transmission or third gear for a manual transmission.
With the scan tool, observe the Vehicle Speed Sensor parameter in the PCM data list.
Does the Vehicle Speed Sensor parameter match the speedometer display?

This is something best taken to a qualified repair shop . This could be a wiring issue , or the PCM or the instrument cluster .

Feb 14, 2017 | GMC Jimmy Cars & Trucks

1 Answer

1994 GMC 2500 pickup with wiper/turn signal/headlight problem.

sounds like you have rats in your dash,or someone has been doing some rewiring,there has to be wires shorted together wired together

Jan 10, 2013 | 1994 GMC Jimmy

1 Answer

Turn Signal Lever is Loose

Just fit a new one the ball bearing spring loaded thingy ahd broke away

Dec 19, 2012 | 1994 GMC Jimmy

1 Answer

1999 jimmy no dash light and signal indicators on

Usually a ground problem - - the lights that are on are grounding thru the cluster.

Jul 03, 2012 | 1997 GMC Jimmy

1 Answer

Instructions on how to replace an odometer cable on a 1994 GMC Jimmy 4x4 with a V6 Vortec motor?

There is no cable,it is all electric.If your speedometer works but no odometer then you have a problem in the intrument cluster.If neither works then you have a vehilcle speed sensor problem which is in the tail housing of the transfer case.

Mar 02, 2011 | 1994 GMC Jimmy

1 Answer

94 Gmc Jimmy left turn signals work, but righr turn signal won't. I replaced bulbs front and rear but they will not flash.

If they come on when turned to the right but don't flash I would say flasher unit. I've seen it before. If they don't even come on most likely switch is culprit.

Aug 19, 2009 | 1994 GMC Jimmy

1 Answer

I have a 89 gmc jimmy s15 everything works on the except the spee

if it is cable driven, then unplug it at the trans an spin the inside of the cable with a drill at slow speed and see if the speed moves, if not then change the cable.

Aug 14, 2009 | 1988 GMC S-15

1 Answer

1997 GMC Jimmy braking problem

the abs control unit controls the speedo (tach) also tells the cruise signal. abs should be fixed or replaced for any of these to work properly with the abs system not working you have no signal to the ecu to say what fuel air mix is for the speed you are doing and will think you are idling.

Jun 07, 2017 | 1997 GMC Jimmy

Not finding what you are looking for?
1994 GMC Jimmy Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

76132 Answers


Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides