Question about 1998 Toyota Corolla

1 Answer

Vent control light out.

How do I get to the bulb?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Expert
  • 173 Answers

Pop the radio cover off, remove the radio, and you should be able to reach back there and twist out the light harness, if not, you can take the hole assembly off by popping out the plastic center console cover. good luck

Posted on Mar 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Daytime running lights don't come on. fuses are good changed module, bulbs are good. no power at the bulb plug. Checked with meter.


Day time running lights(DRL) are controlled by the BCM(body control module). There is a sensor in the upper dash that can be bad. Where the defrost vent is, this is where the sensor is. The defrost vent pops out with a screw driver. You have already replaced good parts. I would get it on a scanner to see whats wrong, before replacing another good part

Mar 14, 2015 | 2005 Toyota Matrix

1 Answer

Where is the fuse for the shifter bulb on a 2002 toyota camry


Most shifter lighting is not a standard bulb. It's similar to a thin belt that has electronic components. this is located in the shifter itself. Might want to remove the cover and check to see is you can replace the item your self.

Sep 21, 2012 | 2002 Toyota Camry

1 Answer

How do I replace the light in the dash for the heating knob ( vent, defroster, etc)


The tiny incandescent light bulb is behind the knob soldered to the circuit board, you must remove the climate control head unit and take it apart to access the knobs back light bulb on the circuit board. You can buy the replacement bulb at Radio Shack, the part number is 7219 Micro Lamp.

Dec 05, 2011 | 2006 Chevrolet Equinox

1 Answer

I need to fix Dash air vent light -Left side - that goes on and off- How due I remove the bulb and check the wiring?


Check out the "Instrument Cluster Light Bulbs" section below:

2002 Volkswagen Passat - Repair Manual - Chassis Electrical (excerpt)

Dome/Map/Cargo Light

  1. Disconnect the negative battery cable.
  2. Remove the bulb from its retaining clip contacts. If the bulb has tapered ends, gently depress the spring clip/metal contact and disengage the light bulb, then pull it free of the two metal contacts.

To install:
  1. Before installing the light bulb into the metal contacts, ensure that all electrical conducting surfaces are free of corrosion or dirt.
  2. Insert the bulb into the holder. If the contacts have small holes, be sure that the tapered ends of the bulb are situated in them.
  3. To ensure that the replacement bulb functions properly, activate the applicable switch to illuminate the bulb which was just replaced. If the replacement light bulb does not illuminate, either it is faulty or there is a problem in the bulb circuit or switch. Correct as necessary.
  4. Install the cover until its retaining tabs are properly engaged.
  5. Connect the negative battery cable.

Instrument Cluster Light Bulbs
The instrument clusters installed on these models are one of 2 types and distinguished by the instrument lighting color, either green or blue.
On models with green instrumentation, only the control light bulbs are replaceable. Should any other failure occur, the instrument cluster must be replaced.
On models with blue instrumentation, none of the components are replaceable. Should a failure occur, the instrument cluster must be replaced.

Map Lights
  1. Disconnect the negative battery cable.
  2. Remove the bulb from its electrical connector.
  3. Installation is the reverse of removal.

Feb 19, 2011 | 2002 Volkswagen Passat

1 Answer

How to replace dash light bulb of 1991 Toyota Previa van


pop fuse cover, remove vent housing, remove speedo upper cover, remove 4 bolts holding speedo remove speedo, change bulb

Mar 31, 2010 | 1991 Toyota Previa

1 Answer

Need to replace dash board backlights - 2004 hyundai elantra


trying to do the same on my 01. ready to change the bulb but can't find it anywhere.
anyhow, here's how you do it:

remove the dash by taking out 2 screws behind the ashtray and 2 above the instrument cluster
begin prying off the dash from the ashtray up, when you reach the heater vents stop. next take a flat head screwdriver and pry off the dash from the left side with the door open. work left to right till you reach the heater vents and it'll come right off. you don't necessarily have to unplug any of the electric connectors if you don't want to, but you;ll have to reach around the dash while working. all you need to do now is remove the heater control unit via the 4 screws around it, then unplug the electric harnesses from the back of it. make sure you remember which goes where. the bulbs are the 3 white (or is it 2 white and 1 grey) circles on the back of the control unit. just turn them with a flathead screwdriver and turn it over and give it a little bump to get 'em to fall out (or grab 'em with a needle nose pliers if necessary). anyhow, that's how it's done, question is, where do ya find the bulbs?

Dec 31, 2008 | 2004 Hyundai Elantra

1 Answer

'01 volvo v70 t5 instrument bulbs


Talking the cluster out of the dash isn't easy, Thats why the Dealer wants so much to do this SIMPLE task. You can do this yourself if you have the time and the patience. remember where all the screws go. some screws are in glove box and others are inside of vents when u can access by gently prying the side of the vent cover with a small flat screwdriver, then look around the cluster fro screws oh and don't forget the screws under speaker covers on dash.

Nov 25, 2008 | 2001 Volvo S60

1 Answer

HEATER LIGHTS IN CONTROL PUSH BUTTONS ON 200 BUCIK LESABRE


I finally replaced the Backlights, using a guide from a person at www.answerbag.com
who wrote:

(i've got an 04 limited. i just soldered in new bulbs for the lighting controls panel (5 #272-1092) and the digital HVAC panel (1 #272-1092 and 5 #272-1154). steering wheel control bulbs are next. )

Just buying a cheap Used one may be the best, if you are not good with dis-assembly and soldering small electric bulbs
Depending on the style you can get a Used One from an online junkyard for 25-50 USD
Check LKQonline out..
http://stores.ebay.com/LKQonline

The most difficult part is getting the Climate Control Module out of the dash, to make the soldering new bulbs repair. The wood-grain Bezel needs to come off, BE CAREFULL, its long and flexible and can crack easy if the wrong pressure is applied or its cold outside or cold in the car cab. Its held in the dash with GM friction clips ( pain in the %$#) and 2 Phillpis screws behing Glove Box door. I worked the pull- pressure from the A/C vent on Right, left-ward to the center, and from Steering Column right-ward toward the center. Once the Bezel is removed, the Climate Control Module is seen, with 4 push-tabs on each corner. BE CAREFULL pushing in the tabs....I broke off one as in pushed too hard. Pry out Right side while pushing 2 right-side tabs gently together. Repeat for the Left Side, while pushing 2 left-side tabs together gently. The Climate Control Module should pop out. Use a 3/8inch Nut Driver to remove the headless screws that hold the Climate Control Module PushButton plate to the box. This will expose the Printed Circuit Board for solder replacement of the Bulbs.

Nov 25, 2008 | 2000 Buick LeSabre

1 Answer

Instrument panel lights


i just recently replaced mine and the temp control had burned . the dash fascia needs to be removed. the vents must come out and then remove the screws that hold it on..there are probably 10 screws.. under the vents , behind the ashtray, and behind the cruise control switch and dimmer switch.. once this is done you need to remove the 4 screws that hold the heater control unit in. the bulb that needs to be replaced lights up temp control and fan speed...you may be able to download an exploded veiw of the dash fascia...this is an involved job...but worth it at night!

Oct 17, 2008 | 1992 Honda Accord

Not finding what you are looking for?
1998 Toyota Corolla Logo

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...