Question about 1992 Mazda 929

1 Answer

Need to troubleshoot a no spark condition on a 92 mazda 929 just replaced t/belt need to know parameters and how to test crank pos sens cam pos sens. coil anything that might cause ignition to not work

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hello, was it working before your replaced the timing belt?

Posted on Jun 25, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1993 Mazda 929 checked battery and starter is good turns over but wont start?


problems include
cam/ crank sensor failures
immobilizer not operational
flat fob key battery
broken timing belt /chain
ecm problem
no fuel pressure
run the fault codes to find the area ans sensors at fault

Jan 08, 2017 | 1993 Mazda 929

1 Answer

How to replace the timing belt on a 1994 mazda 929 3.0 dohc 24 valve engine


Choose:

1994 Mazda MPV timing belt replacement, 6 cylinder DOHC ...

? 3:46
https://www.youtube.com/watch?v=sD2G-NzycvU
Aug 11, 2011 - Uploaded by rsarp
1994 Mazda MPV timing belt replacement, 6 cylinder DOHC 3.0... engine so the valves would not be bent ...

How to replace the timing belt on a 1994 mazda 929 3.0 ...

www.fixya.com/.../t25991928-replace_timing_belt_1994_mazda_929_3...
4 hours ago - how to replace the timing belt on a 1994 mazda 929 3.0 dohc 24 valve... I have a 2000 Mazda 626 4cyl 2.0 liter DOHC engine replacing the timing belt, what ... 2004 6s, 3l. where is the canister purge valve solenoid located?

Where are the timing marks on a 1994 mazda 929 3.0l - Fixya

www.fixya.com/cars/t25991952-timing_marks_1994_mazda_929_3_0l
4 hours ago - where are the timing marks on a 1994 mazda 929 3.0l - Mazda Cars ...1994 Mazda E2000 Cam Timing Mark Positions to Replace Timing Belt ... on a 1994mazda v6 dohc 24 valve engine How to align the timing mark on the ...

Mazda Timing Belt Replacement



Dec 03, 2015 | Mazda Cars & Trucks

1 Answer

Why is my Mazda not cranking up?


There is no magic "fix" button for this kind of issue. You will need to perform standard diagnostics on the vehicle to determine the fault.
Begin by reading out stored codes from the ECU to see which sensors were detecting an out-of-parameter condition, then begin your diagnosis from that point.
Things to check:
  • Timing belt;
  • Throttle Position Sensor;
  • Fuel pressure at rail (after changing fuel filter, of course);
  • Condition of spark plug wires;
  • Condition of spark plugs;
  • Operation and condition of coil pack(s);
  • Operation of fuel injectors;
  • Fuel condition (replace ALL FUEL if you suspect contamination).

May 21, 2015 | 2002 Mazda 626

1 Answer

I have a 03 mits endevour 3.8litre pwr steering belt broke had both belts replaced tried start the vhicle.cranks but won't start.


Check at the area of where the belt snapped what sensors and plugs and wiring could be affected. Most probably either a broken wire or broken or unplugged any connector.or any sensitive sensor has been damaged.

Mar 03, 2014 | 2002 Kia Sportage

1 Answer

03 mitsubishi eclipse 2.4 4 cyl miss fire on 2 and 4 cyl going by the firing order they are not getting fuel the car was running fine shut it off went back 2 hours later and that's when it started...


If you know for a fact the injectors are not opening, you would need to check for voltage and a ground signal from the computer. The computer grounds the injectors to open them based on the crank and cam sensors.

Jan 03, 2013 | Cars & Trucks

1 Answer

I need to replace the 100 amp fuse for a '92 Mazda


Hi, The biggest fuse to be replaced is a 30amp. I don't know what you have that is that big. Could be a relay you have. Usually under the steering wheel and left. Good luck.

Mar 11, 2012 | 1992 Mazda 929

1 Answer

My 1995 Mazda Protege 1.5L was running fine. We were driving home and the car cutoff, will turnover but will not crank. I can take the oil cap off and see one of the CAM's turning and turning freely


if you can see the cam shaft turning then the timing belt is ok
run the fault codes and check for crank position or cam shaft position sensor failures
one or the other or both are candidates for your problem

May 18, 2017 | 1997 Mazda Protege

1 Answer

Car went totally dead, while driving. check spark plugs, there no spark at all. replaced, coil, crank sens, cam sens. still no spark


did you check all fuses with test light, find out if that vehicle has a fuel shut off switch, call dealer. Check those relays and ecm fuses

Feb 02, 2011 | 2000 Dodge Neon

1 Answer

Need timing belt markings for 1989 mazda 929


check aboutauto.com they might have it

Mar 30, 2009 | 1989 Mazda 929

Not finding what you are looking for?
1992 Mazda 929 Logo

Related Topics:

251 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...