Question about Ford Escort

1 Answer

Escort Mk2 1600 valve and torques settings what are they

I want to know the valve clearances on a Mk2 1600 Escort cross flow engine and also cylinder bolt torque settings

Posted by on

  • Anonymous Mar 21, 2014

    torque on cylinder head bolts

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 54 Answers

Cylinder bolt torque settings stage 1 15 ft pounds
stage 2 50 ft pounds
stage 3 85 ft pounds

valve clearences 0.15 - 0.20mm inlet
0.22 - 0.27mm exhaust
these are the figures i have been supplied with, you can also use

cylinder bolts stage 1 10 ft pounds
stage 2 50 ft pounds
stage 3 + 90deg.
with my exp, i would use the first guide as the degree method has a tendancy to snap head bolts, especially on older vehicles.

Posted on May 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cylinder Head bolt torque and tappet settings to suit a , Ford Anglia 1964 105E Engine


Hi valve clearance inlet 0.010 in (0.254 mm). Exhaust 0.017 in (0.432 mm) normal running temperature .. Cylinder head bolts Torque 65 - 70 lb/ft.,.. Cheers

Jan 10, 2017 | Ford Cars & Trucks

1 Answer

Cylinder head torque settings and valve clearance


Hi David:
May I suggest that you Google search the make and model of the engine.with the key words Cylinder head torque settings and valve clearance Odds are you'll find the answer.
Cheers

Feb 19, 2016 | Cars & Trucks

1 Answer

ENGINE TORQUE SETTING FOR ASSEMBLY ON MAINS,BIGENDS AND CYLINDER HEAD AND VALVE CLEARANCE


As you have not specified what engine , I suggest that a workshop manual for the engine would be a good idea as it will have all these details and other information that you will need down the track.

Sep 12, 2014 | Cars & Trucks

1 Answer

Engine torque settings


I don't have those specs, but you can get them here www.alldatadiy.com

Mar 19, 2014 | 1991 Mercedes-Benz 350

2 Answers

Please assist with Cylinder Head Torque and Valve Clearance Specs for Tata Indica 1.4 LXi


i need the head talk settings & valve clearance for tata indica lxi

Apr 20, 2013 | 2006 Tata Indica LXi

1 Answer

Torque settingsfor head on lister petter mini6 engine


I have just rebuilt one for our Westerly 21. This is from my Petter 'A' range workshop manual:-
The water cooled engines (AC1W etc.) are:cylinder head nuts: 30NM (22 lbft) except 32.5NM (24 lbft) for the one that also holds the rocker.
Valve clearances are 0.1mm (0.004") COLDReset valve clearance after one hours running since torquing the head.
Retorque head and set valve clearance after initial 20 hours running
I believe Mini-6 refers to the water cooled engines but just in case, the air cooled engines are 27N (20 lbft)

Mar 27, 2012 | Cars & Trucks

1 Answer

There is a tapping noise in the motor but its not knocking I think its a lifter it hasent lost any power and its really not getting worse I would like to know what the spec is for tighing down the lifter...


Depends on which engine you have. If you have


ADJUSTMENT Although it is sometimes possible to reuse an old cylinder head cover gasket, in most cases it makes more sense to purchase a new one before beginning the procedure. Some vehicles may require the use of silicone sealant either with or without a new cover gasket. For more details, please refer to the cylinder head cover procedures in Engine & Engine Overhaul of this repair guide and refer to the gasket manufacturer's instructions.

Z24i Engine
See Figures 1, 2 and 3
For the intake valves: 1-4-5-8 valve clearance is 0.012 in. (0.30mm). For the exhaust valves: 2-3-6-7 valve clearance is 0.012 in. (0.30mm). The pivot locknut torque specification is 12-16 ft. lbs. (16-22 Nm).

  1. The valves must be adjusted with the engine warm, so start the truck and run the engine until the needle on the temperature gauge reaches the middle setting. After the engine is warm, shut it off.
  2. Note the location of any wires and hoses which may interfere with cylinder head cover removal, disconnect them and move them to one side. Remove the bolts holding the cylinder head cover in place and remove the cover. Remember, the engine will be hot, so be careful!

fb38656.gif


Fig. Fig. 1: Check the valve clearance with a flat feeler gauge-Z24i engine





e459ab8.gif

Fig. Fig. 2: Loosen the locknut and turn the adjusting screw to adjust the valve clearance-Z24i engine


1c1d35c.gif


Fig. Fig. 3: With the No. 1 piston at TDC, adjust the top set of valves FIRST; with the No. 4 piston at TDC, adjust the bottom set of valves SECOND-Z24i engine

  1. Rotate the crankshaft until the timing marks indicate that the No. 1 piston is at TDC of the compression stroke. If you're not sure of which stroke you're on, remove the No. 1 spark plug and hold your thumb over the hole. Pressure will be felt as the piston starts up on the compression stroke.
  2. Refer to the accompanying illustration (upper part), then check valves (1), (2), (4) and (6) using a flat bladed feeler gauge. The feeler gauge should pass between the valve stem end and the rocker arm screw with a very slight drag. Insert the feeler gauge straight, not at an angle.
  3. If the clearance is not within the specified value, loosen the rocker arm lock nut and turn the rocker arm screw to obtain the proper clearance. After correct clearance is obtained, tighten the locknut.
  4. Rotate the crankshaft until the timing marks indicate that the No. 4 piston is at TDC of the compression stroke. If you're not sure of which stroke you're on, remove the No. 4 spark plug and hold your thumb over the hole. Pressure will be felt as the piston starts up on the compression stroke.
  5. See the illustration (lower part), then check valves (3), (5), (7) and (8). Check and adjust valve clearance as necessary.
  6. Install the cylinder head cover gasket, the cover itself and any wires or hoses which were removed. Check the engine oil level.

KA24E, VG30i and VG30E Engines
See Figures 4 and 5
These models utilize hydraulic valve lifters. Periodic adjustment is neither necessary or possible. There is however a bleed down procedure that is necessary when the valve train has been disassembled.
HYDRAULIC LIFTER BLEED DOWN
  1. Remove the cylinder head cover.
  2. Check the lifters for proper operation by pushing hard on each lifter with fingertip pressure.
  3. If the valve lifter moves more than 0.04 in. (1mm), air may be inside it. Make sure the rocker arm is not on the cam lobe when making this check.
  4. Install the cylinder head cover.
  5. If there was air in the lifters, bleed the air by running the engine at 1000 rpm for 10 minutes.


4df22a2.gif


Fig. Fig. 4: Cross-sectional view of an installed hydraulic valve lifter-4 cylinder engine


6e01bb3.gif


Fig. Fig. 5: Cross-sectional view of an installed hydraulic valve lifter-6 cylinder engine

Oct 29, 2010 | 1989 Nissan Hardbody King

1 Answer

Whats the valve clearance for toyota 4k engines and the torque for cylinder head bolts?


valve clearance is .20mm for the intake and .30mm for the exhaust. Will try to find cylinder head torque for you.

Jan 25, 2010 | 1983 Toyota Celica

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,271 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...