Question about 1997 Mazda Millenia

1 Answer

Axel or transmission

Car will not move at all

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 19 Answers

Most Likely Transmission, Unless your Brakes are Locked Up.

Posted on May 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

DIY cv axle 2008 chevy aveo


Jack the vehicle up at proper jack points and lower onto jack stand or stands.remove drivers side wheel. Use needle node pliers and a screwdriver to remove the cotter pin in the axel nut and determine the size of the axel nut. It will most likely be metric 28mm to 36mm. Use an impact to remove the axel nut. Now you will need to remove one or both of the ball joints. Start with the bottom one first and hold the axel in place and pull out on the hub. After you have the hub off of the axel note the splines and how the line up. Now turn the hub so that it is out of the way. You may be able to just yank the axel out of the transmission. If it didn't come out easily you will need a crow bar to gently pry the axel out of the case. Be careful not to put too much pressure on the transmission case. It's aluminum and it will crack and break if you beat on it. Just pry gently and with the transmission in neutral ( be sure to chalk the rear wheels so the car won't run you over) slowly rotate the axel and pry until it comes out. If that doesn't work you will need to rent a slide hammer. Thread it to the free end of the axel and forcefully slide the weight out to knock the axel about of the trans. Installation is reverse. DO NOT USE A HAMMER to force the axel back in you will mushroom the threads and never get the nut on.

Dec 06, 2013 | Chevrolet Cars & Trucks

1 Answer

How do I remove the front left axle shaft on a chevy 2007


remove the axle nut first, always took the upper ball joint loose just take the nut off apply some upwards pressure and hit spindle with hammer and it will allow you to move the hub and all out enough to remove axle. the upper ball joint nut has to come off
and seperate the ball joint from the steering knuckle
then plenty of room. good-day ! then just slide axel out,or pry between axel and ****** to pop it loose, it has a locking clip on transmission side. when putting back in make sure axel is locked in ******. and do not forget to torque axel nut when done.

Aug 05, 2011 | 2000 Chevrolet Silverado

1 Answer

Are the threads on the front wheel axles left or right hand threads? having trouble undoing the nut.


Daewoo is'nt using any left hand threads on cars for sale in the USA. The front axel nut's are sussosed to be very tight, ( 250 Ft- Lbs ) I use a 3/4 in inpac air gun that has 1000 ft-lbs take off toque with the wheel still on the ground and the parking brake on with the wheels choclked. You can still get them off with a 1/2 breaker bar the correct socket and a pipe ( that fits over the handle of the breaker bar) and a sheadge hammer. On the drivers side of the car with the breaker bar parrleell to the floor and sticking out the front, put the pipe over the handle and pust down on the end and wack it hard where the handle is inside the pipe. once it turns it'll turn easy, so watch out! The axel will be stuck in the hub and may be very hard to get out. I use an high powered air chiscil with a pointed bit in the very end of the axel with only the axel nut removed with the wheigh of the car still on the ground, it'll push in about an inch with it all put together. Hopefully after it's moved some it'll be able to be pulled out. Remove the wheel and tire assembly and unbolt the lower ball joint. with it separted from the lower control arm the steering knuckle can be pulled away from the car and the axle pulled out of the knuckle while staying in the transmission. The ball joint part of the job needs to be done with both sides of the car jacked off the ground and supported well with jack satands. I ussally do both sides of the car for axels unless one has already been changed or money for the other axel is'nt available. If your just doing the job for yourself and you don't normally do car repair work, The cost of the tools that you only use to change the axel cost alot more than what you should pay to have the axels changed. I charge $100 to change both axels and $75 to change just one. I buy the rebuilt axels at my local auto parts store for $46 or new ones for $75 sometimes the new ones are cheaper in time as you just buy them straight out and theres no core charge and you just but them go home and put them on and go about you bussness.. It's easy to get hurt putting in axels as the car can fall on you. ( not useing good jack stands and a good hard level hard surface to work on. A good floor jack. a ball joint separterater. the correct axel scoket. The impac scocket and the powerful enough air gun to remove the nut, acess to compressed air to run the air tools. Really a lift to raise the car and hold it good enough that it does'nt fall and kill you. a large pry bar to pry the axel out of the transmission and a large hammer to beat the new axel into the transmission and the brawn and strengh to do all this heavy work.

Mar 08, 2011 | Daewoo Lanos Cars & Trucks

2 Answers

There is a popping sound coming from the front end of my car when I accelerate but only when my car is moving, not when it is parked. Any ideas?


Sounds like your half shafts are going bad. Does it make this noise when turning left or right? If it does your half shafts have gone bad.

May 06, 2010 | 1992 Subaru Legacy

1 Answer

How do i change the rh diff axle seal on a hyundia accent 2002 auto


place the vehicle on a lift (preferred) and remove the RH front wheel. Remove the driver axel retaining nut (1 1/4" nut) and washer. Remove the lower ball joint retaining nut (17mm nut). Using a 10 oz hammer, strike the nuckle where the lower ball joint is attached to it (be careful not to strike the grease boot) while applying downward force on the lower control arm until it pops loose. Once loose, pry down on the lower control are while simultaneously moving the strut to one side untill the joint is clear/away from the knuckle. Now remove the drive axel from the the spline of the hub bearing. Using a pry bar, pop loose the axel from the transmission differential. Installation of the new axel is in reverse order.

Sep 01, 2009 | 2002 Hyundai Accent

2 Answers

Won't go into gear, won't move


Sounds like the transmission.. If the axel was broke most likely it would still go into gear quite easy.. Bad axel would cause bad shimmy in front end.. Suggestion would be to take to a transmission shop and have checked out..

Jul 04, 2009 | 2006 Chevrolet Impala

1 Answer

Replaced both front axels and jack shaft and now the car wobbles


Sounds like one of the new CV shafts has a bad inner joint. It isn't the transmission. Is this a 4 cylinder or V6?
'
'

Apr 04, 2009 | 1988 Honda Prelude

1 Answer

Won't go forward


check the caliper if it is stuck and also check out the front axels and the best way to do this put the front end on jack stands support the car in the back and if the wheels move freely then the problem is in the transmission check the fluid and the linkage on the transmission

Jan 13, 2009 | 1999 Ford Windstar

Not finding what you are looking for?
1997 Mazda Millenia Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...