Question about 1984 Ford LTD

1 Answer

Throttle body carbureator will not rev - 1984 Ford LTD

Posted by on

  • Mike Butler
    Mike Butler May 11, 2010

    Your sure it's not just a carburetor? Year,Make, model, engine please. A little more detail on problem would be good too.

  • its420_us May 11, 2010

    what is the question?

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Expert
  • 63 Answers

Butterfly stuck? jets bad? or carb is shot maybe need to rebuild it does the throttle move

Posted on Apr 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Throttle body float stuck


They are pulling your leg

Only Carburators have Floats

A Throttle Body has Injectors

Could be an issue with the Mass Air Flow Sensor

Wrong reading on air flow you add too much fuel

Dec 13, 2012 | 1985 Chevrolet Monte Carlo

1 Answer

Engine over revs throtle sticking T reg lanos


first off.... does the engine over rev on its own? or only after you press the gas pedal?
does your vehicle have a throttle body that is electronic or cable actuated?..if electronic and revs on own could be one of two issues 1) throttle body itself 2)throttle pedal switch on gas pedal)
if cable and revs after pushing gas pedal ..either there is too much carbon built up on the throttle plate or the throttle cable has begun to fail.. remove the intake tube from the air cleaner to the throttle body and inspect

Jul 28, 2011 | Daewoo Lanos Cars & Trucks

1 Answer

Whare is the TPS sensor located on a huyndai 2007 2.7 L? Does the throttle body have to be replaced along with the TPS sensor. Is the replacement sensor rivited to the throttle body? Scott


on the hyundai the tps rarely fails. so check the pedal sensor on pedal of car. there are 2 sensors on this car, one on side of carburator, and one at accelerater pedal check this one first. the throttle body does not need to be changed to fix the tps. but usually it is located on the throttle body. at the throttle plate.

Jun 26, 2011 | 2004 Hyundai Santa Fe

1 Answer

The eng. will not go over 2000 rpm


disconnect the throttle cable from the throttle body and try to rev the engine

if still cannot rev past 2000 then suspect MAF (mass air flow sensor) or the throttle body...remove the snorkel and check to make sure the throttle plate is moving freely

finally, if when the accelerator cable is removed and rpm's rise above 2000 then suspect the accelerator cable and/or gas pedal

Apr 05, 2010 | 2002 Jeep Liberty

1 Answer

Where are the throttle body plates located


Throttle plates are in your throttle body that open and close to allow more air into intake, Depending on fuel system- multi port fuel injection, Throttle body or carburated. In your case it is fuel injected.

Oct 07, 2009 | 2003 Chevrolet Silverado 1500

2 Answers

My gas pedal is sticking in my 2000 camry


This is due to the throttle flap sticking within the throttle body. The throttle flap is operated by the accelerator cable which turns the semicircular control on the throttle body. Remove the air hose to get access to the throttle body. Use carburetor cleaner to clean out where the flap sits in the body. There'll be lots of black gunk to remove with cleaner on a clean cloth. Reassemble and no more sticking accelerator.

Jun 19, 2009 | 2000 Toyota Camry

1 Answer

My car drives itself, revs high when in park to point of stalling


Bad or dirty IAC( idle control Valve) Romve duct work from air cleaner. Spray throttle cleaner or carburator cleaner with car running at about 1000 -1200 rpms . Aim straight at the IAC inside the throat of the throttle body. It is to the side of the throttle body . Try to aim at the hole and spary 10 seconds into the throttle body. Turn of the engine and let it sit for a few minutes. Then repeat the process. If that does not work, replace the IAC.

Jan 09, 2009 | 1985 Oldsmobile Delta 88

1 Answer

Throttle body on 2001 tahoe


Do this.Remove the air tube from the throttle body.Get some carburator cleaner or equivalent.With one hand,open the throttle,at the same time spray the throttle plate with the cleaner.Clean it well.You might get a missfire for a little while when you start the engine.IT will clear out.This will do the trick.

Oct 03, 2008 | 2001 Chevrolet Tahoe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...