Question about 2001 GMC Sierra 1500HD

1 Answer

Wont start with remote.light blink one than two

Truck wont start on remote.light flash one than twice.polar start 5 button

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Disconnect battery to reset remote starter





Posted on May 13, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have problem with remote control, my remote control gives me blue light to switch the dashboard on but there is no lights coming on the dashboard. what is the problem


Hi, your remote has probably lost its coding. If you have the owners manual check page 65 learning additional remotes. If not do the following 1. Plug in the 6 pin hopped coded plug to control unit under drivers seat. 2. Press unlock button twice to disarm. 3. Press learn button on hopped coded plug. this erases all pre learnt codes. The led on dash should start blinking once per sec. 4. Press learn button on hopped coded plug again. The led on dash remains on for 4 sec. and then starts blinking faster. Ensure to do step 5 within 25 sec. 5. Press any button thrice on your remote that has a problem. 6. In response led on dash remains on for 4 sec and then blinks once per sec.This indicates that the remote has been learnt. Hope this helps.

Mar 09, 2015 | 2006 Tata Indica LSi

1 Answer

Mazda mx5 2005...alarm coming on when i open door..car starts but hazard lights flash for 5 minutes..drives fine then starts again if i open door...help


The car is in theft mode and if you cant reset it with the remote key, you will need a shop to reset it for you. to try the reset with the remote, just use the lock button by pressing it twice, wait 3 minutes and use the unlock button by pressing twice, this should reset the alarm

Oct 12, 2014 | Cars & Trucks

1 Answer

2000 stratus beeps twice, flashes twice, repeats untill stopped, but it drives


This is usually a good situation to bring to alarm shop and have them take it out and see if you can just keep the remote start or it might need a new brain on the alarm system

Dec 10, 2013 | 2002 Dodge Ram 3500 Truck

1 Answer

Remote control has stopped working. Have tried changing the battery of the remote control but that did not work.


Does the red light on the remote light up when you push any of the button
if no, replace remote
if yes, then try repograming the remote to the car again.
-Have remotes' ready. if you have two then fob#1 and fob#2 (doesn't matter which one is #1 or #2)
-each step has to be done within 5 sec or it will not work, but don't do it super fast.
1.turn key just to the "on" position (not starting) and push "lock button " on fob#1 once and release
2.turn key off
3.turn key just to the "on" position (not starting)and push "lock button " on fob#1 once and release
4.turn key off
5.turn key just to the "on" position (not starting)and push "lock button " on fob#1 once and release
6turn key off
7.turn key just to the "on" position (not starting) and push "lock button " on fob#1 twice (if you only have one fob, then stop here and go to step 8)and push the "lock button" on fob#2 twice.
8.turn key off and remove key from ignition.
if you did it right, remotes' should work again.
good luck

Dec 17, 2010 | 2003 Honda Accord

1 Answer

Do in need a scan tool to program a 2001 cabrio key


Programing the button REMOTE portion of the key is simple.
You do need 2 keys. You must be able to lock the drivers door and have the red led alarm light next to the lock button blink. If it does not blink, the alarm does not know the door is closed and will not go into program mode. Put one key in the ignition switch, turn on, do not start engine. Close the door, use 2nd key, turn door lock and hold in lock position for 10 seconds. Release key to neutral position.
Press a button on the remote, within 2 seconds press the same button again, the turn signal lights will flash,
this indicates your remote matches the car system and is now recognized. Unlock door remove key from ignition.
So don't pay extra 99 cents to $5 for these instructions in hopes of getting the KEY to function with the car.
Instructions are only for the keyless remote, not the key.

May 27, 2010 | 2001 Volkswagen Cabrio

1 Answer

My sl 280 1997 wont start, it turns over ok,the two lights for the alarm in the rear view mirror are flashing red and green is there any way i can bypass the imoberlizer


Point remote at mirror
Press lock/unlock button twice

Within 30 seconds turn ignition to position 2
Should reset if you have no other problems with immobilizer

Jan 04, 2010 | Mercedes-Benz SL-Class Cars & Trucks

2 Answers

Blinking panel lights


To Calibrate , start and warm engine to normal operating temp. with engine idling turn blower switch to high, turn mode switch to panel, open all outlets, move temp lever to full cold.
press and hold rear wash and rear wiper buttons simultaneously for 5 seconds (untill all leds illuminate.) all leds should light up for 5 seconds, rear wiper and intermittent rear wiper button leds will flash alternatly during calibration... after 60 seconds if only rear wiper button led is flashing, cal. is complete

Jun 18, 2009 | 1998 Plymouth Voyager

Not finding what you are looking for?
Cars & Trucks Logo

720 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...