Question about Honda CR-V

1 Answer

Rear wiper motor broke

Rear wiper stopped working, tested fuse, it's good. I think wiper motor burned out, how do I remove it?

Posted by on

  • Stefan Lacaille May 11, 2010

    You will need to open the tail gate and take the handle off with a flat head to start with and then get a No. 2 star head to remove the handle. The garnishing that surrounds the inside of the tail gate just snaps into place...On the edges of it grab with your hands and a small flat head gently but firmly pull down on the garnishing. Once you get the garnishing off you will need a socket set to pull the motor off...There should a lot of patients when doing it.

  • Anonymous Mar 25, 2014

    Trying to find out if there is a relay fuse for this model

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 75 Answers

Well you going to have to open the tailgate up and remove the inside cover that is attached to it. You will need a small flat head and a No. 2 star head screw driver and some gloves so that you don't cut your hands....

First where the handle is remove the caps on the handle and then remove the handle there may be a small pocket around the handle to remove it also with the screw driver....And then remove the garnish from around the tailgate by using the small flat head and your fingers to pry it off with....Remember just to take your time when doing this and wear some safety glasses so that nothing goes in your eyes.

Once you have removed the garnish you should see the wiper motor there should be three bolts that hold it in place and wire wire coupler that it hooked up to it. And before you undo the motor you will need to go on the outside of the tail gate you will need to remove the wiper arm off of the motor and then take the rest off after that.

Posted on May 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear wiper motor does not work fuse is ok honda crv 2003


About rear wiper, if the fuse is OK, I suggest test the switch, the wires and voltage at/from motor; finally, test motor, possible go to bad.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day

Aug 22, 2012 | 2003 Honda CR-V

1 Answer

The rear window won't open or close. the rear wiper dosen't work either. Both stopped at the same time. I can't find a blown fuse. Im not sure where to look next.


If the wiper motor when bad, and stop in any position ,other than its resting position, the rear body ecu disable the window motor, Do this test remove the rear panel and at the same time that the wiper switch is On ,tap the motor with the hammer gently if it gets activated the problem is the motor.

Dec 27, 2010 | 2003 Toyota 4Runner

1 Answer

1993 vw golf rear wiper doesn t work replaced wiper motor tested motor all ok when on car no good


check the fuse for the rear wiper maybe blew when replacing it if not you have a short also check the rear wiper switch make sure working correctly

Sep 24, 2010 | 1997 Volkswagen Golf

1 Answer

I dont have an owners manual for my renault megane w reg, the rear wiper is not working & there is no space in fuse box for a fuse, is there somewhere else for a fuse for this


Rear wiper morors are notorious for developing faults, Access the motor wiring and test for power. I don't think there is a designated fuse for the rear wiper but a call to Renault dealet will clarify. The less frequent use and water ingress is top of suspect problems. Good luck

Apr 05, 2010 | 2000 Renault 181

1 Answer

My rear wiper has stopped working on kia sportage 2006. can hear switch ok and fuse ok, how do i remove trim to get to rear wiper motor


Test for power at motor.


Test for power at motor. If you have power, then replace.wiper motor. trim should be held on with panel clips that can be removed with a special panel removal pliers






if

Mar 11, 2010 | 2002 Hyundai Santa Fe

1 Answer

Rear wiper not working when try to turn it on nothing happens on my jeep liberty


first check fuses if all good remove back hatch panel find wiper motor remove plug . turn the ignition key to on position turn on rear wiper now test wiper plug for power if no power replace wiper motor

Jan 04, 2010 | 2004 Jeep Liberty

2 Answers

I have a 2003 GMC yukon, the rear wiper does not work,the fuses are good, what should I look at?


JUST PUT A NEW GROUND WIRE TO THE REAR WIPER MOTOR............SIMPLE GOOD LUCK

Dec 07, 2009 | 2003 GMC Yukon

2 Answers

Rear Windsreen wiper motor runs continuousley in


The "stop" function is in the motor of the wiper...remove the fuse and call it a day...You shouldn't use it anyway the rear glass is "soft" in these cars and the wiper action will damage the glass over time.
Sorry :o(

Jun 14, 2009 | 2002 Volkswagen Passat

1 Answer

99 Nissan Quest real wiper runs continually when ignition is on


Principles of Operation
Operation of the windshield wiper and washer is controlled by the front wiper/washer amplifier assembly. The front wiper/washer amplifier input comes from the multifunction switch by means of a voltage divider circuit. A constant voltage is applied to the multifunction switch by the front wiper/washer amplifier. When the multifunction switch is moved into the LO, HI, or intermittent position, the voltage is directed through a series of resistors. This results in various voltages being returned to the module for each switch position. The module then grounds the appropriate circuit, based on the voltage signal received back from the multifunction switch. This causes the wipers to run intermittently, or at the appropriate speed. Voltage is supplied to the wiper motor by the CJB fuse F46 (20A).
When the multifunction switch wash button is depressed, it bypasses all of the resistors returning a full voltage signal to the module. The module then grounds the appropriate circuits to operate the windshield washer pump for as long as the switch is depressed. The windshield wiper speed is dependent on the position of the windshield wiper/washer switch.
Voltage for the windshield washer pump is also provided by CJB fuse F46 (20A).
Operation of the rear wiper and washer is controlled by the rear wiper/washer switch.
Voltage is supplied to the rear window wiper motor by the fuse junction panel fuse F44 (10A).
The rear window wiper motor ground is made or broken by the rear wiper/washer switch. When the rear wiper/washer switch is moved into the WIPER position, it grounds the rear window wiper motor circuit, causing the rear window wiper motor to run once every 10-15 seconds.
Voltage to the rear washer pump motor is also supplied by the CJB fuse F44 (10A). The rear washer pump is directly controlled by the rear wiper/washer switch which makes or breaks the ground for the washer pump motor, depending upon its position.
If the vehicle is equipped with a movable liftgate glass, a liftgate glass switch is utilized to prevent rear window wiper operation when the liftgate glass is open. This same switch also causes the rear window wiper to drop down approximately three inches when the liftgate glass latch is released.
------------------------------------------------------------------------------------------
  • The wipers stay on continuously — rear wiper
  • Circuit.
  • Rear wiper/washer switch.
  • GO to Pinpoint Test L .


---------------------------------------------------------------------------------------------
Measure the resistance between rear wiper/washer switch C288 pin 6, component side and rear wiper/washer switch C288 pin 2, component side.
  • Is the resistance less than 5 ohms with the switch depressed, and greater than 10,000 ohms with it released?
sxv~us~en~file=arrow.gif~gen~ref.gifYes GO to L2 .
sxv~us~en~file=arrow.gif~gen~ref.gifNo INSTALL a new rear wiper/washer switch. TEST the system for normal operation.

Measure the resistance between rear wiper/washer switch C288 pin 6, circuit WB08 (BU/YE), harness side and ground.
  • Is the resistance greater than 10,000 ohms?
sxv~us~en~file=arrow.gif~gen~ref.gifYes INSTALL a new rear wiper /washer switch. TEST the system for normal operation.
sxv~us~en~file=arrow.gif~gen~ref.gifNo REPAIR circuit WB08 (BU/YE). TEST the system for normal operation.

65501dd.gif 7e9d21a.gif

Dec 08, 2008 | 1999 Nissan Quest

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

631 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...